8th Gen Civic Si - k20 RBC J35 Port Matching DIY

Рет қаралды 2,244

rcysiFg2

4 жыл бұрын

Decided to drop this video finally, just a quick video on how I port matched my IM to my J35 Throttle body.

Пікірлер: 37

@ahs9583 3 жыл бұрын

Can u do that without removing the intake manifold?

@rcysiFg2 3 жыл бұрын

You Could. But I wouldn't recommend it. You want to be able to flush the intake maniold out of all the debris after porting, before you run the motor.

@zakx2623 4 жыл бұрын

Hey bro I'm changing my k20 manifold to prb/prc and gonna put j35 tb where can I buy the adapter for it

@rcysiFg2 4 жыл бұрын

You're swapping your rbc for the prc?

@zakx2623 4 жыл бұрын

@@rcysiFg2 swapping my RAA TO PRC

@rcysiFg2 4 жыл бұрын

@@zakx2623 oh ok, not sure honestly. But I'd check hybridracing and hardmotion

@zakx2623 4 жыл бұрын

@@rcysiFg2 thanks bro

@faithflores7851 4 жыл бұрын

Where can I find paint

@rcysiFg2 4 жыл бұрын

I got it at autozone.

@faithflores7851 4 жыл бұрын

No primer?

@rcysiFg2 4 жыл бұрын

@@faithflores7851 I didn't honestly. Just wiped it down with scotch bright, than alcohol / grease remover and painted it. Would be good to primer it probably.

@faithflores7851 4 жыл бұрын

For sure I’ll do same steps as you thanks for help 🙏

@rcysiFg2 4 жыл бұрын

@@faithflores7851 Np 👍

@solidstreetrunz3956 4 жыл бұрын

What is the tool called that you used to do this ?

@rcysiFg2 4 жыл бұрын

Dremel... I used a Dremel 200 to be exact.

@solidstreetrunz3956 4 жыл бұрын

rcysiFg2 okay I appreciate the reply ! Also is there different tips? If so which one did you use? I’m not familiar with those tools at all

@rcysiFg2 4 жыл бұрын

@@solidstreetrunz3956 np, ya theres lots of tips. I used the wood sanding bit. You'll go threw a few but with the wood but you wont gouge the metal.

@rcysiFg2 4 жыл бұрын

@@solidstreetrunz3956 www.lowes.com/pd/Dremel-200-17-Piece-2-Speed-Corded-0-86-Amp-Multipurpose-Rotary-Tool/3824377?cm_mmc=shp-_-c-_-prd-_-tol-_-google-_-lia-_-129-_-rotaryandoscillatingtools-_-3824377-_-0&store_code=1693&placeholder=null&gclsrc=aw.ds&&gclid=Cj0KCQiAoIPvBRDgARIsAHsCw08WwHQXYd3FOsaBSSQGzTxcI8CJTTAKqhGxLlNF2E1qf8GIBydiVggaArAfEALw_wcB#

@solidstreetrunz3956 4 жыл бұрын

rcysiFg2 awesome and one last question.. what did you do to clean the manifold out after you ported it ? From all the shredded little metals