Not bad.a better converter would help alot

I bought a new Lentech Aod. It comes with a solid 1 piece Input shaft. Which is the aod weak link. You definitely need that if you plan to keep the aod. The other stuff isnt as important but it comes with a new valve body that gives you the ability to shift all 3 gears. It has a switch for overdrive so it doesn't go into overdrive while racing also the shifts are nice and crisp

Just to add to my earlier post. You dont have to get a lentech Trans. You could just get the valve body and bring your trans to a shop that does work with high performance parts. They will know what to do with the one piece shaft and put better clutches and other parts in the trans. Wait for converter till you figure what cam you are using

@@91lxaod53 are u doing the Aod shuffle

@@willsilversurfinharris6239 No. I have a lentech built AoD which gives me the ability to shift 1st to 2nd then 3rd. Overdrive is now electronic. I have to switch it on and off

@@91lxaod53 nice my car is the same way. I go 1 2 3 then a switch for od. It has a stand alone gen 1 quick shift controller. I was told the car has a Aod shell with 4r75w billet internals. Its chirps seconds and 3rd gear. 331 boss block 70mm on3 car.

No I haven't had any problems. I put a B&M transmission cooler on it the biggest size and a deeper B& M pan. I also don't drive the car that much either. I do drive it to the track though

@@91lxaod53 if you would have daily drive down it & only took it on the track on the weekends, do you think it would have lasted well on the factory modified AOD?

@Oscar Villarreal it would be fine just install a temp gauge and change the fluid once a year. My friend made 750 hp with a built aod and drove it to the track

@@91lxaod53 Wow...! Really! I was wondering how high you can push a stock AOD. I also like it cause its lighter than other Race performance transmissions. How long has he been pushing 750 hp. With that AOD?

@@91lxaod53 & would you happen to know what kind of transmission internals does he have? Did he put a heavy duty kit or did he put 4R70W?

What mods to the trans? The 355 may be a little to high at east 373.

@@91lxaod53 I thought 355 gears are lower than the 373? In videos people say the highest gear you should put if you want to daily drive your Fox is 355. If you do a 373 and above that's more for drag racing.

@@91lxaod53 Mods like a shift kit, the valves, a cooler... Etc. For the stock AOD?

@@awee5816 you're right 355 gears are better for daily driving but they may hurt you from getting in the 12's with the combo you want to use.

@@awee5816 you will need to replace the 2 piece input shaft to a solid one. A new valve body would be good and of course a new torque converter.? How many miles are on your transmission

At that time 265. I've since changed the combo a little

Check my page I have the info on there about the car. I will try to get more videos up thanks

I think it was 8.01

It's the street terminator from Lemtech. It has the wide gear ratio set electronic overdrive and 1 piece input shaft

12.62 . It's not heavily modified.

I does have heads cam Intake 373 gears lentech trans with 3000 stall converter

@@91lxaod53 very nice. I’ll be happy if mine gets into the 12s. What heads

@@KS-89LX at that time Ford aluminium gt40 x305 heads 58cc. With trick flow stage 1cam and trick flow street heat intake 65mm 75 mm mass air. Actually changing heads this weekend to trick flow twisted wedge 11r heads

@@91lxaod53 that’s awesome. Putting a edge 3400 in my car currently. Ported gt40 heads long tube headers explorer Intakes 65mm TB a cam very similar to TFS1 4.10 gears I’ll be happy with anything 12.xx for now

I wish it was a bracket race. That vette is alot faster than my car

@@91lxaod53 you were moving pretty good there sir! Are you still running the stock torque converter?

No I am not I have a 3k stall 9inch converter

Wow. I'm sure that torque converter helps get the car moving .I have a 91 GT with an AOD. It had HCI and 373 gears. I'm going to try a converter next

I have a lentech transmission in my car with a one piece input shaft. Becareful adding a losser converter. Those things are none to break