Friends, this cool idea for angle grinders justified itself and deserves the attention of the audience.
I will show you how to make wood discs for angle grinders from old oil filters with your own hands.
**Video by episode.**
00:00 What can be done with a homemade disk for angle grinders
01:50 Two options for a nut for a homemade disc
02:12 How to make an angle grinder disc from an oil filter
03:42 Testing a disk for an angle grinder from an oil filter
06.30 We try to cut a nail with a homemade disk.
07.25 Recovery disk for angle grinder after a nail
07.36 How to balance a disk for an angle grinder
☑ - Store disk for wood for angle grinders - alli.pub/6fgioy
☑ - My website - 1000ss.ru
💡 - Disc for wood from self-tapping screws - • ДИСК ПО ДЕРЕВУ ИЗ САМО...
💡 - Disk on wood from a grater - • Крутая самоделка из те...
💡 - Metal etching • БОЛЬШОЙ ТОПОР МЯСНИКА ...
💡 - Metal burnishing • ПРОСТО СУПЕР - ВОРОНЕ...
A homemade wood disc for angle grinders is ideal for do-it-yourself wood sampling. This cool angle grinder idea has paid off and will help you make wooden plates, spoons, ax handles and other items effortlessly. This cool idea deserves the attention of viewers for a number of reasons. Homemade does not require costs and it is easy to do. Used oil filters can be found at a car service. Cut a thick metal plate as shown in the video. The rest of the filter can be discarded. And now a life hack. Prepare some self-tapping screws as it was done in the video. And weld the self-tapping screws to the plate from the oil filter with an electrode or semiautomatic device. Excess welding can be cleaned. The landing hole of the cup most likely will not fit the angle grinder nut.
Therefore, in addition, you need to make a nut for the disc from the oil filter.
It took me no more than half an hour to make one disk for angle grinders. That is why this cool idea for angle grinders is worthy of the attention of the audience. But that's not all.
I ran a series of tests. Tried to clean the car. Conducted a series of tests on pine bars. I made an ax handle from a birch log. A large spoon from a dry oak branch. And a deep plate made of oak blanks. Oil filter discs have done a good job of treating wood and can save you a fortune. The grinder did not burrow into the wood and did not overheat. That is why this cool idea for angle grinders justified itself and deserves the attention of the audience. At the end of the video, I did a vandal test. He hammered the hundredth nail into a pine beam.
And I tried to sample. The small disc cut clean wood like butter. When I hit the nail, the grinder worked almost the same way. Except that it was felt that something interferes with making a sample. The nail after a few seconds became 6 millimeters shorter. Self-tapping screws became blunt and began to process wood noticeably worse.
After such tests, the store disk can be thrown away. We simply remove the homemade disk. And as they say again, we can cut a notch on the knee with our own hands with an ordinary metal disk. And keep sampling. How do you like this life hack? This is a really cool craft.
Surely one of the viewers will ask a question about balancing. In a few years, I made 6 different disks for sampling. And none of them had a heartbeat. Although, I don’t know what a beating is from rumors. One of the reasons for the normal balancing of homemade products is the weight of the disk. They are much lighter than the factory ones. And the welded pieces of self-tapping screws are of the same size and light enough. I think that is why there are no problems with balancing.
Those who find it difficult to believe it can check it out for themselves.
Now you know why this cool idea for angle grinders justified itself and deserves the attention of the audience.
The video was prepared for you by the author of the channel 1000 DIY's and Advice - 1000 HOMEMADE AND TIPS See you in new videos!