Man I love how the texture completely helped hide the seams from the prints

"Capybara with Mascara" sounds like a lovely children's book, if you ask me.

Beautiful, just a quick warning. Be *really* careful working around CA glue with hot tools. If you hear up dry CA it can release a bunch of vapours which are *really really* bad for your eyes and lungs.

Okay i pull up

"okay i pull up" - Don Toliver, 2020

Always great to watch your creative approach to extending the possibilities of 3d printing.

I really liked that grass, it really adds to the piece. Great job!

you're in for a treat: with the iron, you can also MIX COLORS! It's like oil painting.

Great video as always. Now I want to try this too, the process looks so calming

Here's another quick tip if you find yourself struggling with aligning the sections: You might've seen some prints with cutouts and extra cubes or cylinders to print as joining pieces, but you don't actually need those extra parts; just cut 1.9 mm diameter holes (that should compensate for the inaccuracy of small printed holes, but this is just for regular 1.75mm filament) into your model (I personally use blender and "boolean subtract" small cylinders from the model) and use small lengths of filament as the "dowels". Either use blind holes (i.e. the spot for the "dowels" isn't accessible from the outside; leaves a nicer surface on organic models) or, for structural parts, consider through-holes and then "rivet" the filament, i.e. use a flat-bladed soldering iron or woodburning tool, on fairly low heat, and just smoosh the filament lengths into the surface; it's got respectable holding power so you might not even need glue, and for flat planes you can sand them so the "rivets" hardly show at all. I've used it loads of times, in fact my motion system on my Ender3 is a custom LR sled and I joined two pieces to keep the layer lines parallel to the pulling force of the timing belt; it's been going smoothly for more than a year now, so I'd say it's much more rigid than you would expect - definitely beats having your print delaminate xD

he really did in fact pull up to the party

I'd love to see you make some super detailed dioramas, using all of those textures and technics to enrich the whole thing, also It'd be nice to see you make some tiny monsters of your own design

I'm actually significantly more impressed with this make.

I think a little acrylic pain and dry brush would really make all the work you did with the heat tools pop!

Excellent video!

Mascarabara!

The capybara fur alone is great but the fuzzy skin samples are a great help. Just in the slicer alone it's not good to see how it's gonna turn out. I'm still gonna print my own samples.

Thats how my grandpa used to stipple his gun grips.

It might be fun to roll the icosahedron and use the resulting texture on a print, like a little game! The two empty sides could be a "roll again" kind of feature.

Love this! Great creative suggestions!

He pulled up fr 😳

A video I can really get behind

Yay, he's back from shorts only! :)

This is Brilliant would love to see more of this!

no age restriction to make art!

Looks great. Definitely going to give it a shot on a couple of projects.

Those fuzzy skin test cubes : "How to make 3d printed ramen" Nice video :)

for the eyes, you could print it with a cylindrical hole there instead, then fill it with a blob of black filament using a 3d pen. I've done this with some models I printed, and it came out great!

CAPYBARA

beautiful carpincho devin!

I always love your videos!

Very great effect, thanks

That's some A grade Dürer stuff right here. NIce!

that test piece could probably work as a fidget toy

thanks for reminding me of the fuzzy skin its actually useful for something im making

Ah fuzzy skin, been using that for a while now in PrusaSlicer. Nice to see some awesome manual methods though! Thank you!

You missed an opportunity to call it a Lovely CapyHaira instead of Lovely Hairy Capybara @ 13:26 but I'll let it slide! Love the sample piece you did at the beginning. Fantastic idea when starting out! Trying a new idea like this is way less likely to mess up your intended target!

"Capybara Mascara" t-shirts when?

Great stuff

You should do a swirl next

Still have my 3D Simo mini, would love to say its going strong, but after a couple of years of heavy use...its time for an upgrade.....if I ever get the time lol

Capybara? Capybaaraaa!

13:18 - I recognize that from the movie poster for Stanley Kubrick's lost treasure, 'A Clockwork Capybara'.

the fumes PLA releases are fully non-poisonous so if you print something in PLA you don't need the ventilation for that

I love your Vids

Try a heated wire brush? could work for animal hair.

Everytime he says "Bear-ah" it kinda kills me on the inside

Ok he pulled up

An alternative brush hack would be to use a tooth Pick. You can proportianate the Paint better. Its also good for very tiny strokes.

While true that the smooth effect from the burner alone isn't what most would consider smooth by printing standards. I bet if you were to print large props at thick layer heights it would be pretty fast to smooth it with a burner and then use a traditional spot putty/smoothing alternative to achieve the classic smoothed 3D print look, or at least faster than sanding, primer, sanding, spot putty, sanding, spot putty, sanding, etc.

you were my inspiration to get into 3d printing for years and years, but I've never quite had the budget to get a 3d printer, but I've finally put my foot down and ordered one, It's arriving on the 3rd

please do one on how to add textures via software.

You can actually use displacment maps eg. in Rhino3D to achieve a fuzzy effect on a per face basis.

This whole video should be a triptophobia warning lol

Does it pull up?

if you cut the model in half along its length and rotate 90 degrees each half you only have to add support for the legs that are the only small parts that leave haging on.

Nice now I can 3d print ramen noodles 🍜

Can you share the correct link to the Woodturning tool you use??

Did you try tue 3dsimo v2?

is the capybara made out of ground or is ground made out of capybara

hi dev!!!!

You triggered my trypophobia waaaayy before the warning.

U need a orange for his head 😂

the CA looks like peanut butter

Delicate work, amazing result

would you please provide a link or at least the exact name of the 3D pen in the description? I've been looking for the right 3d pen for me for a while now. Thanks!

That grass...

capybara 🥺🥺🥺🥺🥺🥺🥺

“Wheaties?” I think you mean shredded mini wheats.

💕👌👍

Give that poor capybara a watermelon

ok i pull up

HEPA filter ....filters particulates NOT fumes unfortunately...activated carbon filters will, but a fume hood/paint booth, suck and redirect elsewhere will be the standard setup

Devin, nothing to do with this video, but have you ever watched any Follygon videos? You both sound exactly the same.

Where are your older videos?

Great video my man!!! But you should totes make some cheese.

Ok I pull up

Ok I'll pull up

OK I PULL UP

High quality horizontally spinning rat?

the way he said capybara ☠️

Thanks for the Trypophobia warning 👍

I pull up

add a texture to yourself maybe scales or octopus suction bois

The mynt3d pen sucks on anything that isn't pla low flow rate compared to the bulky cheap pens that can actually get a lot hotter

ok i pull out

but I’m learning the mobile version

Is this gort or quandale dingle?

Why not make capibara with small holes over all 3d print and then thread some synthetic hair in color of capibara hair?

If anyone can help me with a much needed heel prosthetic, please send me a message. I’ve been dealing with a very particular heel injury due to a bed sore from a hospital stay that has deeply affected my life over the past 5 years, especially considering the shutdowns. If anyone has any advice or can facilitate a modeling and printing of something resembling a reverse scan of my opposite heel, please send me a message. I will absolutely do my best to compensate anyone who’s willing to help me escape the immobility and chronic pain I’ve had.

ADD LASHES!!!

From my personal experience 3DSimo seems like more of a cash-grab rather than a company trying to make a decent product. I got a 3DSimo pro but it quickly started breaking and several features didn't work. The 3D pen function was also painfully slow and you couln't draw anything other than joining plastic. Their customer support is basically non-existant too!

Is it just me or the thumbnail looks like something x-rated going on under the mosaic? Poor capybara😅​

very original ok i pull up joke

capybAra, not capyberaw 🤭

bad move with the big cottonbud "brush", other than that, it's so fun seeing this! It's like sanago doing 3D printing

First?

Trypophobia anyone? 😵‍💫

Whole point of 3D printing is to not do the work yourself. Hoping future printers can simply print that detail at a fast speed.

GROUP FARTING STARTS AT 9PM