Nice I like your Bracket that's some good Engineering

I've always liked the pairing between esu loksound and digitrax

I designed my own bracket like this for athern blue box trains. Ill post the .stl files on thingy verse under "athern decoder mounts"

Nice job on the decoder bracket. It's about Tim someone has come up with that for older units and especially the Blue Box versions. I do have a few of those that I have tries to restore with decoders and is near impossible cause of the room in them as u have explained. Curious would you be willing to sell some as I would be interested in buying a few. What would u be willing to sell them for. Would love to hear from you on this. Again exceptional work. Nice job

Awesome bracket. My question would be why not extent the other end as a speaker support? Hope your marketing them bybtime i get my new layout up cause i have a bunch that need coversion that i so want to run DCC

you should be selling that bracket !!!!! Very nice design

First off thank you for doing these videos also I'd be interested in buying a few of those brackets you built for the DCC but I'm interested in did you do any videos on the old blue box 1500 locomotives I run southern Pacific and I want to convert them all over to DCC I like to know what you would recommend but I also want sound thank you very much I look forward to your reply

Great video! I had 6126 as my first engine but it got so old that it probably became impractical to do a DCC upgrade. But I turned to this for an FEC unit I found for next to nothing. This bracket is awesome. I'd love to get a hold of the 3D print of it, but see no links. Can probably do something similar with styrene though. Now my question is how did you wire the iPhone speaker in, and do I need to be careful about it drawing certain amounts of amperage from say a Decoder Buddy? Thanks

Lots of interest in your bracket. Any plans to market either the part or the code to make it? Putting DCC in Athearn Blue Box locos has been an exercise in McGuyvering at my house. Factory add-on brackets with the pigtails are just too d@mmn clunky and big.

I'm also interested in the install bracket. Have you set up marketing them as of yet, or is the software available to print out the bracket?

I just found your videos. Good information. Do you have the decoder bracket for sale anywhere on the internet? I have 15 - 20 blue box locos..

I checked thingverse but did not find the bracket. Could you just supply a drawing for those without 3d printers. I could use styrene to make one?

Can you share the .STL for the bracket? If not, I’ll just make my own, but don’t want to reinvent the wheel

Like d your video on your Athearn Blue Box GP40 install. I was interested in two things: 1) Your design for the 3d printed frame. 2) Wanted a video to hear the sound of the GP40 with the Iphone 5 speaker. Thanks.

Great Bracket. You selling them on Ebay yet? I would be interested in the brackets. I also have a shelf full of the ol' blue boxes that I need to convert to DCC. I hope you copy-right annd sell idea back to Athearn :)

You going to sell the brackets? Thats a great idea!

Nicely done...What decoders did you say you were using? Excel? Also curious where to get those decoder holders you presented. Looks nice! Thanks for sharing.

Great video and tips. Can we hear the XL decoder with an iPhone speaker? Have you done that combo?

Any possibility of selling brackets for athearn blue box SD and GP units? Because I have some Blue box Athearn units that I would like to convert to dcc sound.

Don't see other video listed concerning the led light mounts

Would you kindly post the model of the decoder used? Thanks

How thick is the mount/shelf you created to place the decoder on?

U have stl on thingyverse for decoder mount?

The iPhone 5 , where did you find this speaker. Does EBay have this? Did it come from overseas or was it from state side. In the near future I plan the start going to DCC and sound to me is important.

hi jais 14 years its been 3 years that I have been doing railway modeling I am very interested in your decoder support I would like to have the link to print with my 3d printer would be nice jet a lot of athearn blue box to convert and its brilliant as an invention thank you for your help Xavier

Will you share the 3d print file?

You should sell them! a I would buy them and I'm sure many others would too

Any interest in selling a bracket/light kit? That seems to be the best adapter I’ve come across.

Video of stl?

Do you sell those brackets?

Do you sell the brkt?

Can you share your stl please.

Please sell your printer code - my locos are all bluebox - they just keep working and working with little maintenance. I have access to 3d printer at work but no cad skills at all. Can I buy the code for the adapter and brackets, please? Cheers. Kim Australia

So op never ul a stl of bracket

Not the one in the video

Never mind previous comment. Found the video

Hey can I purchase 6 of those brackets from you. Please