Thank you

Thank you and thank you for watching.

Thank you!

are you high?

I saw the sub company’s documentary and noticed the extension on their gamepad and copied it. 😁

Hi. I never owned an orange cube but based on my understanding and experience of gps guided drones, their accuracy is about of a few feet, depending on the number of satellites received. You can observe it during rtl. It never goes back on the exact spot. You need to at least supplement it with a vision system to guide your vehicle to exact path.

Hi. It is an old mobius camera I have connected to a 5.8ghz standard video transmitter. On the receiver end is just a standard 5.8 ghz video receiver from my groundcontrol station build video. Pretty basic fpv video setup.

Update: i wasnt able to get my ppm encoder working, but I was able to get it working with a different reciever that just supported sbus 🤷‍♂️

May I know what motor driver you are using?

I am using two ESCs.

@@user-wj8li4fe2c The motor drivers I’m using are for dc motors. They are capable of reversing the polarity going to dc motors making them turn the opposite direction. You are not using ESC for brushless motors (drone motors) are you? If you are, I’m not familiar of any capable of reversing.

SyRen 10A. It's already obsolete. You can replace it with newer versions and higher amperage. Thank you for watching

Hi Hariharan. I lived here in the US. I bought these parts either in amazon or the local hardware store. For Autonomous Lawn mower. I don't advise you use the tracked rover as they work on skid steering. That means they need to skid just to turn. This is difficult on grassy surface and you need to have very powerful motors and mechanical parts to do this. You will be better off using the separate thrust and steering method like the ones they use on electric wheelchair. If you could afford to purchase those used ones the better.

Thank you sir..now I have improvement in idea Without flysky remote control ,is the possible to drive rover in auto mode by using mission planner..

Please, share me a cost estimation for what's you done in above video. Please share me a link to be the full setup requirement to buy ... Your kind reply.. helps me to achieve my major project for academic

@@Hariharan.K.03 yes. As you can see in the video, I’m not using an rc radio. I’m only using the telemetry radio and the mission planner.

Yes sir... i review that you using with mission planner Thank you sir...

Thank you for watching. Yes, ardurover is a ground drone. I use pixhawk in my other videos for quadcopter as well.

Bro liked your video . But can you make a rover with a small budget yet fully functional

Hi, you don’t need an arduino to perform autonomous missions. Pixhawk is capable of saving and running missions on its own. Watched your video and saw your build. Pretty cool. I may use cytron controller also in the future. Thank you for sharing.

Thank you for helping me with my doubts, I built it to help my father in the field since I broke my back, I am a professional driver and due to my injury they cannot operate on me and it is over for my international truck trailer trip I hope when you make more things I can see them and if you see I can improve mine even more I will be happy I wanted to make it prettier but I don't solder and the drawing on paper to do it physically changes everything a lot I wanted to make a body that stands up like a hood so it looks like a truck With the Tesla one I wanted to do something like that but I don't understand nor do I have any practice with fiber or polyester resin. For me this is now economically impossible for me but hey at least I don't lose the hope of doing good things to entertain myself while!@@LyndonsWorkshop

Yes. Unfortunately I don’t have a safe place to test missions as cars pass by the area every few minutes.

​@@LyndonsWorkshopThanks for the reply. Could you give me the model name/item name of the motor controller? Can I use a Esc driver for dc motor. This is pwm control. Thanks in advance

@@surflaweb Hi. I’m using a SyRen motor controller. Choose an amperage higher than your motor current draw. As for the esc, I don’t think you can use an esc (the ones used on quadcopters) as it is for 3 phased winding inside the brushless motor. While brushed dc motors only have 2 wires.

@@LyndonsWorkshop ok I see that this is currently discontinued, for small dc motors can I use a l298n driver?

@@surflaweb Hi. I did a quick look on l298n motor controller. It seems to need a pwm to control the speed and separate signal to control the direction. I don’t think its compatible with pixhawk. As pixhawk only sends pwm to control both speed and direction.

Hi user-fv9hc6py2o. I didn't test how much load it can accommodate. Depending on your application, you can replace it with more powerful drill motors. I am only using 12v drill motors with 10A motor drivers. This build was just a proof of concept and meant for demo in a science project setting. Do you have a particular load in mind?

Maximum load 500-600 kg. 100-150 kg the frame and the main construction and other will be an external load. Is this pixhawk board capable of working bigger loads if we increase the power of the electric motors in watt?

@@user-fv9hc6py2o this setup definitely cannot accommodate that amount of load. I was initially thinking of recommending you the electric wheelchair setup as the mechanical design and motors already designed for heavy load but that one also is not enough for your requirement. The pixhawk microcontroller will output pwm signal to control the motors. It is the motor drivers and the motors you should change to accommodate your load.

Thank you very much for you immediate and very helpful answers! Thank you also for your very interesting video’s!!

You don’t have to program ardurover. Just install the firmware and play with some settings. It’s easy once you know how.