Adding Simple Steps To Your Rock Sliders. (Great Beginner welding Project).

Рет қаралды 505,112

3 жыл бұрын

Let's improve the protection and usability of our rock sliders by adding a small step! This is a great project for folks that are brand new to metal fabrication and you don't need advanced fabrication tools or experience to build these. Any welder, grinder and pipe bender (even the HF pipe kinker) is all that is necessary to build a great set of rock sliders. If you want to spice it up with a dimple die, these can be found at Swag Off-Road, sold in single die or even Ebay! Unlock a little creativity and build one of a kind parts for your 4x4! Rocker protection is a great way to start!
EMPIRE ABRASIVED 10% OFF: "dirtlifestyle" lddy.no/qf79
AMAZON ITEMS!!! www.amazon.com/shop/dirtlifes...
(Amazon Affiliate Links)
BARNES 4WD COUPON CODE: "dirtlifestyle" 10% off
NORTH RIDGE 4X4 CODE: "dirtlifestyle" up to 20% off www.northridge4x4.com
EMPIRE ABRASIVE CODE: "dirtlifestyle" 10% off lddy.no/qf79
YANKUM ROPES: yankum.com?afmc=1l
ONX MAPS: webmap.onxmaps.com/account-pu...
MIDLAND RADIOS: bit.ly/2IjmlZD
STEP 22:
EVOLUTION POWER TOOLS CODE: "dirtlifestyle" store.evolutionpowertools.com/
JOOLCA HOT WATER HEATER: bit.ly/37qLgEp
Shirts & Hats on our website!!
www.thedirtlifestyle.com
Support us on Patreon! / dirtlifestyle
Follow me on social media!!
Instagram: / dirtlifestylenate
Facebook: / dirtlifestylenate
DISCLAIMER:
Due to factors out of the control of Dirt Lifestyle, we cannot guarantee against improper use or unauthorized modifications of this information. Dirt Lifestyle assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Dirt Lifestyle recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Dirt Lifestyle. Be safe!
This video and description contains affiliate links, which means that if you click on one of the product links, I'll receive a small commission.
#metalfabrication #welding #4x4

Пікірлер: 428

@brianpardee1281 3 жыл бұрын

So glad you went full time on this you have my favorite offroad KZfaq channel and the fab is top notch

@DirtLifestyle 3 жыл бұрын

Thank you! I'm honored!

@David-rj1ru 3 жыл бұрын

i'll pay

@jizzler1418 3 жыл бұрын

I was writing my letter to Santa for Christmas and number 3 is to fabricate like Dirty Nate from KZfaq. I’ll keep my fingers crossed. Great video again man!

@DirtLifestyle 3 жыл бұрын

Lol awesome

@mikekeran8661 3 жыл бұрын

Always quality content and fabrication!

@DirtLifestyle 3 жыл бұрын

Thanks!

@Jakeex 3 жыл бұрын

best channel out. love how detailed your explanations are and how you tell us the alternatives to what you choose to do. and always good to see you use the ‘backyarder’ type tools too, good to see you don’t need all the expensive stuff to still produce good quality work 👌🏼👌🏼

@codylee5132 3 жыл бұрын

Can't wait to get a welder and start working on projects like this! Thanks for the video!

@blackhawkinternationalsecu6962 3 жыл бұрын

Awesome sliders. Gives me some ideas to try for running boards for my van.

@chrisdenning9816 3 жыл бұрын

Thanks Nate. Appreciate the explanation for the design you chose. I need to build mine for the FJ60.

@ebalmes 3 жыл бұрын

Awesome timing. Sliders are the next step for my XJ. Can’t wait to get some more stuff built.

@bransencortez7353 3 жыл бұрын

That was really cool, i cant wait to start on my new comanche project and make a simmilar style front bumper as the low Buck

@finnishfatman 2 жыл бұрын

Been eyeballing these rock slider DIY videos of yours lately and they are pretty damn nice, filled with tips and how to do things. I'm fairly confident I could now start fabricating sliders to my Jeep WK and even make them look decent 😁

@aaronyoung8028 3 жыл бұрын

Hi Nate, I was planning on building rock sliders soon, and those dimple dies turn it from functional to awesome. Thanks 🍻 Cheers Aaron

@bquade70 3 жыл бұрын

Excellent, just fabbing up my sliders for my RAM 1500. Keep up the great content 👍👍

@ayost62 3 жыл бұрын

Awesome video! This is what I'm going to be doing to my XJ very soon after I fix the rust issues lol.

@jeremymcclain3241 3 жыл бұрын

Very Very nice!! Less is more! And those sliders are perfect! I like the fact that you picked a weld pattern for them. Practiced and achievement!

@jonathanharmon23 2 жыл бұрын

Design on the fly is completely my fabrication style! Love it!

@pointblankyt9878 3 жыл бұрын

Your such a Inspiration for me your fabrication work is amazing and love the Channel

@fish_built 3 жыл бұрын

Always interesting seeing other perspectives on armor. I would never be worried about/never seen getting a tree stuck between tire and slider (being in the desert) but my kickout sliders have pushed me away from walls and rocks loads of times, I would never not have a kickout for the wheeling I do. PNW wheeling is so different than the Utah desert.

@kidgokuxl 3 жыл бұрын

That was great! I wish they were on my Jeep. Thanks for the video! 🇺🇸

@momobadilak 3 жыл бұрын

I love the fabrication content paired with the offload experience stories - very cool

@kakarote2277 3 жыл бұрын

You just made what I'm thinking of making. You solved /answered many of my questions. 👍👍👍🇺🇸🇺🇸

@kevinwatt5629 3 жыл бұрын

Good call on not reversing the dimple dye! Works with the roof rack way better. I would ryno liner type paint to off set the loss of traction.

@xmo552 3 жыл бұрын

That sticker is.... awesome. "I'm walking on sunshine! Oh oh" 😁

@theclaydoking 3 жыл бұрын

Thanks for the awesome ideas in this video I was just going to make some rock sliders in the coming week thanks alot from Australia

@gertc3240 3 жыл бұрын

Love the fabrication mindset! Those welds looks amazing! This is my go to channel for Disco mods! Keep up the good content!👍🏻

@andremuscat181 3 жыл бұрын

I really enjoy watching your work on your disco.. I am rebuilding one from scratch aswell for expedition .. all d way from Malta ! really good work !

@benjaminreinhardt259 3 жыл бұрын

I take my jeep on the beach a lot. The dimple dies like you have them are more friendly on bare feet. Looks good.

@zachheindl8619 2 жыл бұрын

Subscribed.....got a 1990 Bronco im gonna combine your instruction on DIY Rock Sliders and this video with the step to make a set of sliders for it. I cant wait!

@TheSprinkle27 3 жыл бұрын

Man, I ABSOLUTELY LOVE & RESPECT YOUR WORK.

@ATEMOFFROAD 3 жыл бұрын

Sweet setup! Good info! Might consider this for an add on, cheers

@jasongoulart3697 3 жыл бұрын

Good timing for this video. In the process of making sliders for my YJ. Thanks

@DirtLifestyle 3 жыл бұрын

Nice! Good luck with the YJ! 🤘

@cliffordsmithey464 3 жыл бұрын

Thank you for the good examples on different techniques on The dimple dies could you oh maybe done one or two in certain areas the opposite direction to give yourself a step and still have that look

@joshsmith4488 3 жыл бұрын

Your videos are so entertaining, I real enjoy how you answered the questions that I have in the episode. I honestly doubt I will ever build anything like what you can do but I like watching you build them. 👍🏻

@DirtLifestyle 3 жыл бұрын

I appreciate it my friend 👍

@brandonjohnson8914 3 жыл бұрын

Just want to say thank you for doing what you do I try to watch every video I can you do a great job of explaining things I'm just starting out in the Fab keep it up

@dylansyjadventures3148 3 жыл бұрын

Man! You’re edits have always been great but this is movie like!! Great for you man!

@abrahamespinosa2297 3 жыл бұрын

Saludos amigo desde Antofagasta Chile mi amigo 🇨🇱siempre veo todos los vídeos son muy buenos y se aprende mucho gracias por enseñar lo que sabe 👍👍👍👍👍👍👍👍👍👍👍👍

@WeekendWrenchTurner 3 жыл бұрын

Good stuff, going to do this to my sliders in the future so saving this as a reference. Thank you!! 🍺

@willhikearizona 3 жыл бұрын

Like the dimples. You could also powder coat with some grit for traction.

@MrL0Single 3 жыл бұрын

Gha, Nate... You are just killing it! The quality is 👌. All of the shot setup... Yee yee! Thanks for taking the time... We appreciate it more than you know!

@DirtLifestyle 3 жыл бұрын

Thank you! Much appreciated!

@OrdnanceTV 3 жыл бұрын

Buying my first welder this weekend. This will absolutely be my first project. By the way, LOVE the depth of field in your product shots 👍👍 Thank you!! Love your videos.

@DirtLifestyle 3 жыл бұрын

Nice! It can be frustrating at first but enjoy yourself and take your time! You will love 🤘

@jshoffner67 3 жыл бұрын

Great job Nate. Always enjoy watching your mad fabrication skills!

@DirtLifestyle 3 жыл бұрын

Thank you!

@ronthoman7138 3 жыл бұрын

AWESOME! Thank you Nate ~ Excellent detail and craftsmanship as usual!

@DirtLifestyle 3 жыл бұрын

Thank you!

@itsajeepthing3856 3 жыл бұрын

Well crap now I want to take my sliders that are exactly like the old classics from 15 years ago with the three center supports and add some webbing to them. I had been using some traction tape but that stuff wears and looks like crap after a season. With two young kids and a wife riding around in my TJ with me getting them in and out safely is important. This was awesome and thanks for inspiring a beginning fabricator!

@banzaiib 2 жыл бұрын

thanks! Your shots have solidified the design i'm going for. I snagged a flux core welder and have been practicing on 1/8 plate. Just bought a bunch of 1018 dom and square tube and am starting on the build for my '19 ranger. The FCAW welder doesn't make particularly pretty welds (can't stack dimes because of the flux), but i'm making some strong stringers and will just grind smooth anything too ugly :)

@BigfootTJ 3 жыл бұрын

Your barnes code has saved me about $100 so far on my 1 ton swap, and that's just the front axle. Thank you!

@soulsurfer8797 3 жыл бұрын

Your ability to teach is unparalleled. You should consider writing how to guides and create a full didactic guide compiled into sub sync series in order or arrange your videos on here to act as a how to guide which tells a full build in order. Truly thank you for sharing Nate!!!

@DirtLifestyle 3 жыл бұрын

Thank you very much, that is a giant compliment and I appreciate it 👍

@chrisandshazza01 3 жыл бұрын

Could watch welding all day. Beautiful work👌👌

@MichaelGalletly 3 жыл бұрын

From watching you, I've decided to try some of this stuff myself. I have a basic drill press and standing bandsaw. need to buy a welder, but not sure what to get to start.

@uncletoddsgarage 3 жыл бұрын

Wow! Those are awesome! Can’t wait to make some for my Rzr on my channel. Your fab videos are quickly becoming some of my favorites to watch! I learn so much!

@samb2636 2 жыл бұрын

Love your videos & your disco. Keep up the great work 👌

@FlawedOffroad 3 жыл бұрын

These turned out great!

@chrisandshazza01 2 жыл бұрын

Beautiful work and agree with the dimples facing down👌👌🤘

@psyekl 3 жыл бұрын

Looks fantastic. We had the same HF bender in our shop without the power assist (we added length to the handle) and it was definitely a workout. I tend to overbuild so the only thing I would have done different is add pieces of tubing at either end of the plate for added bracing (though admittedly, it wouldn't have looked as good).

@eddaeges9309 3 жыл бұрын

Its fantastic to see the quality and great ideas with simple tools. Not a $4000 tube bender but things a Do it yourselfer can purchase at the local Harbor Freight and it works. Great channel.

@rubenvor 10 ай бұрын

That's some nice fab man! Thanks for sharing ☺

@chriswoodroffe7762 3 жыл бұрын

Hi Nate, Great video, as always. I love that you explain how to get the same result without having all the expensive tools. I’m new to fabrication and am learning a huge amount from your no bullshit videos, thank you. Have you ever done a video fabricating a swing away tyre mount? It’s my next project and I’d like to see how you would do it.

@briandetrick2688 3 жыл бұрын

Bro you just got a subscriber.and patron.just sent you ahondo.love your ch.realy itsyor presents.deminior.your just a normal guy.thats figured things out.1 thing I like is family videoes.like y'all go 4x4ing to a camping spot.we goabout 6weekends ayear.i love seeing families in to this.and your wife is kick ass she's got your back bro.

@davidroyle5552 2 жыл бұрын

Now that's just great....more stuff I have to buy. I just got the welder you have. I want to get the finger brake and the dimple die and punch set. Piece by piece it will happen. Just keep it up and I will keep buying stuff and having fun in the shop. I'm gonna be in soooo much trouble with the wife. LOL

@cincybrian5177 3 жыл бұрын

Fantastic, Nate! Big help. 👍

@kasperhauser3731 2 жыл бұрын

Another excellent video. Thank you.

@TwistedEngines 3 жыл бұрын

Well done as always man !

@702cyco 3 жыл бұрын

Good stuff, as always!!!

@mrmidnight32 3 жыл бұрын

Paint the step and apply some non skid or soft sand to the top. Love how far your channel has come btw man! I remember watching your first build years ago. Stay humble and ride the success train. Don’t have any 4x4 rigs but I enjoy watching your builds as if they were my own.

@DirtLifestyle 3 жыл бұрын

Thank you!

@davidzarazua8441 3 жыл бұрын

Hands down one of the best fabrication channels here on KZfaq. I'm always impressed on the quality of work both in fabing up stuff and video editing. Keep up the great work 👍

@DirtLifestyle 3 жыл бұрын

Thank you! Much appreciated!

@F4izzle 9 ай бұрын

Looks really good!

@MrRICK244808 3 жыл бұрын

Awesome video im just getting in to doing fabrication on my avalanche so this help out alot 👍

@erikandersen4811 3 жыл бұрын

Thank you for the video! I intend to do steps like this on my old truck now. 😀

@erikandersen4811 3 жыл бұрын

It’s an beater of a truck that is a total sleeper. No one realizes it’s a muscle truck when they look at it. I think the steps will just help it look like more of the bad ass that it is while maintaining a low profile. 😀

@hipairbrush1053 3 жыл бұрын

Another nice build my friend. Very informative.

@ceshadow76 3 жыл бұрын

Congratulations, excellent video greetings from Peru

@shanes_bs2659 3 жыл бұрын

Another great how to vid. Always very informative!

@bowmaster24 3 жыл бұрын

On the back porch, whiskey in hand, and watching Dirt Lifestyle. Hard to beat!

@robertmcnear204 3 жыл бұрын

Always awesome info and knowledge. Keep up the hard work, favorite channel by far hands down

@DirtLifestyle 3 жыл бұрын

Thanks!

@p0tat0c0mp 3 жыл бұрын

I can't wait for the episode when you dimple all the body panels on one of your rides! haha Great videos, editing and super helpful info for someone who doesn't know what they're doing (me). Keep it up dude!

@DirtLifestyle 3 жыл бұрын

Lol thanks man!

@zuk4wd 3 жыл бұрын

That looks incredible !

@JoeGarofaloII 3 жыл бұрын

This is like watching Michaelangelo working through his sculpting process. well done sir, cant wait to incorporate this into a future build of mine!

@DirtLifestyle 3 жыл бұрын

Thanks Joe 🤘

@slateslavens 3 жыл бұрын

He definitely is a fab artist.

@ZjOverlander Жыл бұрын

Clean work man!

@nickleewein6142 3 жыл бұрын

As Always an amazing video to pass the time and to encourage my imagination

@johnjosephswain9230 2 жыл бұрын

Absolutely brilliant.. Luv n best of luck from India

@LJ_Jeff 3 жыл бұрын

Man you make this stuff look so easy haha. Not that it's a really hard task but its seems so easy watching your videos. Another quality video! Keep up the great work man.

@plank407 3 жыл бұрын

You made a good move with your own channel. Really enjoy your work.

@basskickinredneck 3 жыл бұрын

Those look so dope. Great work Nate

@gocoastgaurd721 3 жыл бұрын

I love this channel. This is what overlanding is all about, not buying every piece of custom gear under the sun. Make your own and having fun! Too many $150K rigs on youtube and far too few really really cool custom ones!

@luzgonzalez2838 3 жыл бұрын

Enjoy it a lot.Thanks for your videos.Adsome.GBY!

@dorsk84 3 жыл бұрын

I would just make that kick out, all the way up to the tire. But I do understand exactly why you chose your design.

@TheBibleExplorer 3 жыл бұрын

Those turned out great,I am looking forward to seeing all you have in the works for the Disco, it's looking awesome brother 👍

@DirtLifestyle 3 жыл бұрын

Thanks buddy!

@imedina619 3 жыл бұрын

love the work man !

@zacharysmith5947 3 жыл бұрын

Now I have to follow you, LR3! Very Nice Additions!

@dannyprovencher7862 Жыл бұрын

I really like your work, great stuff

@moabwheeling 3 жыл бұрын

You never disappoint Nate . Great job my friend . Looks amazing and very strong . Take care and be safe my friend.

@DirtLifestyle 3 жыл бұрын

Thanks brother 🤘

@craigfuller6187 3 жыл бұрын

Great video. I’m going to add this to my Jeep.

@joerowland7350 2 жыл бұрын

I like it I going make a set soon just got get the dimple die I'm thinking of puting sand on wet paint in 2 layers I'll try it on scrap first

@ryandeweese363 3 жыл бұрын

Hey, to combat the compromise of going with the traditional dimple direction, instead of inverted for more traction, after paint, you could "Tread" the dimpled center section with grip tape!! You get the look,And traction!! Awesome videos man, keep up the good work!!

@VictorVectorJKU 3 жыл бұрын

Great Video Nate! Super clean side steps and well laid out and thorough thought on the process! Also really killer meeting you last weekend at Tahuya in the wife’s Disco!

@Wooskii1 3 жыл бұрын

Another great video 👍Coming from ATV's I love "tree kickers". I've been in situations where I would have bent the rear axle, or much worse, from sliding into or grazing trees. I get how 4x4's are different, but I think you can build them right if you don't plan on changing tire size or suspension. I really want to build a set but I already have the 2x4 mod on my XJ, and I don't know how to incorporate them into the 2x4s and fenders...

@cbchevy74 3 жыл бұрын

Nate you motivate me. I have the tools, but I don’t have the 220v power in the garage. Now I guess I need to go wire up a plug and get to work. I just hate welding on new rigs. (I have an 18 4runner and 19 Cummins)

@KnightDriveTV 3 жыл бұрын

I worked over 10yrs to accumulate my tooling...chassis dyno, TIG/MIG/Plasma/benders/fab tables/lifts.....but unfortunately I lost it all. Working hard to get back and started my youtube channel 10mo ago...would love to get back to fabbin...for now I'll watch you do it. I used to fabricate all custom forced induction systems, headers, intake mani's, etc. Hard work, but sick when it's done.