Adjusting the Rollers on Your Anlin Sliding Patio Door

Adjusting the Rollers on Your Anlin Sliding Patio Door | Anlin Windows & Doors

Рет қаралды 382,546

7 жыл бұрын

If your sliding patio door is hard to slide while opening and closing, the rollers may need be to adjusted.
Open the door slightly and look at the reveal or gap between the door and the frame.
The roller adjustment screws are located on both ends at the bottom of the sliding patio door.
Use a Philips head screwdriver to adjust the roller adjustment screw. Do not use a screw gun and be careful not to strip the screw. Turn the roller adjustment screw clockwise to raise up the door. Turn the roller adjustment screw counterclockwise to lower down the door. Continue making adjustments until the gap or reveal between the door and the frame is even from top to bottom. Adjust the other roller adjustment screw if needed.
Check to see if the door is sliding smoothly. Repeat these steps if further adjustment is needed.
Routinely clean the track with a vacuum or wipe thoroughly with a damp towel to keep sliding patio doors operating smoothly.
anlin.com/care-maintenance/
#AnlinWindows
Music: www.playonloop.com/2013-music-...

Пікірлер: 28

@AndresGarcia-lz9gg

Excellent video. Thank you and thank you for what you do.

@Navmanz_ 3 жыл бұрын

This really helped me fix my double roller door as it wasn't aligned properly and we had to hold it tight together to get it to lock. It's so much easier now after adjusting the rollers to get it to align. Locks easy and smoother as well. All thanks to this video tutorial.

@Miguel-mq3xp

Thanks!!!

@wihiss

Thank you! Now I have my patio door fixed.

@allisondethloff655 5 жыл бұрын

Thanks! I could hardly open the door at all! After doing what the video said, I also took the door off completely (lift up over track) and was able to clean the track you can't get to on a daily basis, and it had at least a 1/4 " of dirt and hair in there which was also making the door stick and squeek. After I got all the dirt off the entire track, it works like a charm!

@ricklee6196 2 жыл бұрын

Well that Fixed my misaligned door! Thanks

@carolynperry9408 6 жыл бұрын

This is not the brand of my door but the instructions were great and I fixed my door so it glides like a knife through soft butter.

@BibleExposition2022 5 жыл бұрын

Need to advise people to lift the frame of door up to prevent stripping of the screw when making the adjustment because the weight of the door is on the screw when it is turn. Thx

@jasonables8119 3 жыл бұрын

Fixed my door! Thanks.

@manjitsingh-fq5ht 5 жыл бұрын

Thanks for this video , u save my money

@hynesightweddingfilms

Wow, thanks. I hope it works

@stantons9309

In south Africa the screws are retracted inside a hole.

@williamgrissom9022 6 жыл бұрын

My problem is the track cracked. Like the video, it is just thin plastic w/ a stainless steel cap. The moveable Anlin door is 47" wide and double-pane, so apparently too heavy for the track. We have rarely used that door, and much less since it got very hard to close from the broken track. Another Anlin door 37" wide was installed the same time ~2002 and its track is still OK. A lot of manufacturers used these same plastic tracks, but Anlin should have evaluated them more. I am looking for a smarter design to replace, but even getting the original track is proving tedious.

@Drekt666 2 жыл бұрын

i dont have a upper screw in mine, i have a hole on both ends and only a screw at the bottom. how do i adjust that?

@marissakondelik1993 Жыл бұрын

Is it just a simple screw that I can remove and replace? I have one that is completely stripped

@mikesters3532 Жыл бұрын

What does one do if you run out of adjustment and sliding glass door is still not square? Had brand new door wall installed and needless to say they did a less than stellar job. Top of slider leans forward and roller is fully adjusted up and rear fully lowered. Now what?