Can this sad broken C64 be saved?

  Рет қаралды 548,935

Adrian's Digital Basement

Adrian's Digital Basement

4 жыл бұрын

This Commodore 64 main board had so many things wrong with it, it was a fun challenge to get it working again. Previous owner(s) had caused damage to the board by removing chips, which adds an extra layer of difficulty to troubleshooting. It all starts with the dead test cartridge doing nothing.
In this video, I show my techniques for troubleshooting and fixing all of the problems.
--- Video Links
Special thanks to IZ8DWF who has given me great advice on repairs:
/ @iz8dwf
C64 main board schematics:
www.zimmers.net/anonftp/pub/cb...
Diode Symbols:
www.rapidtables.com/electric/...
--- Tools
Deoxit D5:
amzn.to/2VvOKy1
store.caig.com/s.nl/it.A/id.16...
Jonard Tools EX-2 Chip Extractor:
amzn.to/2VazxDS
www.jonard.com/Products/EX-2-...
Wiha Chip Lifter:
amzn.to/3a9ftWw
www.wihatools.com/precision-c...
O-Ring Pick Set: (I use these to lift chips off boards)
amzn.to/3a9x54J
Elenco Electronics LP-560 Logic Probe:
amzn.to/2VrT5lW
Hakko FR301 Desoldering Iron:
amzn.to/2ye6xC0
Rigol DS1054Z Four Channel Oscilloscope:
www.rigolna.com/products/digi...
Head Worn Magnifying Goggles / Dual Lens Flip-In Head Magnifier:
amzn.to/3adRbuy
TL866II Plus Chip Tester and EPROM programmer: (The MiniPro)
amzn.to/2wG4tlP
www.aliexpress.com/item/33000...
TS100 Soldering Iron:
amzn.to/2K36dJ5
www.ebay.com/itm/TS100-65W-MI...
EEVBlog 121GW Multimeter:
www.eevblog.com/product/121gw/
DSLogic Basic Logic Analyzer:
amzn.to/2RDSDQw
www.ebay.com/itm/USB-Logic-DS...
Magnetic Screw Holder:
amzn.to/3b8LOhG
www.harborfreight.com/4-inch-...
Universal ZIP sockets: (clones, used on my ZIF-64 test machine)
www.ebay.com/itm/14-16-18-20-...
RetroTink 2X Upconverter: (to hook up something like a C64 to HDMI)
www.retrotink.com/
Plato (Clone) Side Cutters: (order five)
www.ebay.com/itm/1-2-5-10PCS-...
Heat Sinks:
www.aliexpress.com/item/32537...
Little squeezy bottles: (available elsewhere too)
amzn.to/3b8LOOI
--- Links
My GitHub repository:
github.com/misterblack1?tab=r...
Commodore Computer Club (of Portland, Oregon and Vancouver, Washington)
www.commodorecomputerclub.com/
Tivoo Pixel Art Display seen in my videos:
www.amazon.com/Divoom-Tivoo-r...
--- C64 Stuff
JaffyDOS:
blog.worldofjani.com/?p=3544
C64 Test Harness I use:
• Building a Commodore 6...
C64 Homebrew cartridge PCB: (used for the DeadTest / Diag Cart I use)
www.ebay.com/itm/Commodore-64...
EasyFlash 3 Multi-Cart:
store.go4retro.com/easyflash-3/
--- Instructional videos
My video on damage-free chip removal:
• How to remove chips wi...
--- Music
Intro music by:
Nathan Divino
@itsnathandivino
Outro Music:
Abyss by | e s c p | escp-music.bandcamp.com
Music promoted by www.free-stock-music.com
Attribution 4.0 International (CC BY 4.0)
creativecommons.org/licenses/...
--- Image Credits
None

Пікірлер: 1 400
@brianv2871
@brianv2871 4 жыл бұрын
Well, it's nice to see that C64 finally fixed. I had given up, and after watching that video, i'm sure i'd have never gotten it fixed on my own, so thanks! I have a Zener diode to fix that cassette port from a (would you believe) worse parts board. Also another SID chip (I might have put the flaky one i had in there because I didn't want to risk a good one in that board). Just need to track down a PLA chip (or PLAnkton).
@LeftoverBeefcake
@LeftoverBeefcake 4 жыл бұрын
Go for the PLAnkton! I have one in my original C64 from '83 and one in my SX-64 and they work wonderfully, and run very cool. I would never again want to use an original-type PLA chip when they are basically time bombs.
@DrTofu83
@DrTofu83 4 жыл бұрын
Agreed. A PLAnkton runs colder, doesn't die on you and has the potential to outlast the C64 board :)
@brianv2871
@brianv2871 4 жыл бұрын
Adrian has something he's testing that might be a cheap alternative to pla's or Plankton's so I'm waiting to see how that goes.
@DrTofu83
@DrTofu83 4 жыл бұрын
@@brianv2871 I'll be waiting for the magic Bell Icon too. I'm really interested of anything able to replace a PLA
@alteregos8949
@alteregos8949 4 жыл бұрын
@Jayson Cowan at this stage of the game we are well past the early on point that’s for sure. 37 years and still locating working ones is getting harder and harder these days.
@gregghernandez2714
@gregghernandez2714 4 жыл бұрын
This is one of those videos where about half way into it I wonder to myself: "Why on Earth am I watching this, I have never owned or will ever repair a Commodore 64 computer." Then it dawns on me, just like when I watched a guy construct a scarf joint on a large wooden beam....there is something very satisfying about watching true masters work at something, and continue to work on it until it is done. Okay now on to watch some glass blowing expert. LOL.
@PeterJaquesMusic
@PeterJaquesMusic 4 жыл бұрын
same, though i did used to own a c64 (even into college!). i would never repair one, but it was just super engaging to watch the mystery unfold
@thomaswilson9780
@thomaswilson9780 4 жыл бұрын
I actually could have written this comment!!
@psour33
@psour33 4 жыл бұрын
I strongly agree :)
@kaczan3
@kaczan3 4 жыл бұрын
I'd recommend to you channels about renovating old metal tools and knives.
@martynlewis5901
@martynlewis5901 4 жыл бұрын
I work on domestic gas equipment (boilers, fires & cookers etc) in the uk. I’ve always been fascinated/interested in computing and owned a ZX Spectrum (amongst others) back in the day. I would love to get into this sort of thing but wouldn’t know where to start. I frequently use a multimeter for working on boilers but this is a whole different skill set.
@olafwagner
@olafwagner 4 жыл бұрын
"total novice" is being way too hard on yourself - this is some 'level 7 - chip ninja' stuff you are pulling off. very impressive and well done for your tenacity in getting it done.
@SpaceButler010
@SpaceButler010 4 жыл бұрын
Anyone who can repair that thing is not a total novice. This was a ton of work that needed know-how, investigation and skill.
@StrapMerf
@StrapMerf 4 жыл бұрын
experience trumps training anyday.. a few minor things would have helped with formal training, and knowledge of failure modes, but they would have saved a few minutes at most.. training makes gaining experience slightly less painful.
@Mike3DPro
@Mike3DPro 4 жыл бұрын
Novice?! you have scopes laying around AND a bald head! That pretty much makes you god mode by itself 😎
@metesev
@metesev 4 жыл бұрын
Someone having an oscilloscope and using it to test the chips ain't a novice :) Novice is someone like me only using the solder iron or doing some point-to-point tests :)
@jdryyz
@jdryyz 4 жыл бұрын
Have to agree. You're definitely above the Novice stage. More like Advanced.
@Seafox0011
@Seafox0011 4 жыл бұрын
This is better than watching a TV drama - so many unforeseen twists and turns as the narrative unfolds. Puzzle logic is indeed fascinating.
@radiofreak0
@radiofreak0 4 жыл бұрын
Wow, I've just sat here for 40minutes not knowing what the hell was going on,but utterly transfixed😃
@RichardCatto
@RichardCatto 4 жыл бұрын
yeah, me too. I just wanted to see if he could get it working again. pretty amazing to watch actually.
@normanbates19
@normanbates19 4 жыл бұрын
Hahahaha me too! I love watching electronics repair videos, but have absolutely no bloody idea what it going on
@MrAndroidData
@MrAndroidData 4 жыл бұрын
same here
@VamosConLaPeli
@VamosConLaPeli 4 жыл бұрын
Guys, there are good electronics tutorials on the web, you might want to check out www.electronics-tutorials.ws/ or simply throw into duckduckgo.com the words "electronics tutorials". And you might also want to get familiar with the Arduino IDE (implies also learning C++), which allows to program many different microcontroller boards of different architectures (AVR [e.g. ProMini or ProMicro], ARM [e.g. STM32F103C8T6], or some wi-fi connected ones like NodeMCU ESP8266...). You might also decide to put that together with what you learnt in the electronics tutorials and design some extra hardware to use with your microcontroller board, you'll have to test it on protoboards and then maybe use KiCAD to make a PCB (you might buy a budget oscilloscope like Hantek DSO5102P and a KKmoon dual channel signal generator, both great value for the money... or maybe something more expensive). I've come to watch this one because I have been a C64er for quite some years, also doing some assembly coding on it :D and of course I remember some great whole-summer-night videogame sessions with my brother, we are now living in different continents.
@themetalmicky
@themetalmicky 4 жыл бұрын
me too, im bamboozled
@Sypaka
@Sypaka 4 жыл бұрын
KZfaq; "Yo, you like electronic diagnostics and repairs?" Me: "Well, kinda." KZfaq: "Then just look at this, yo!" Was not disappointed.
@bloeckmoep
@bloeckmoep 4 жыл бұрын
Hmm, I only have a tip for you, when dealing with bad sockets and chips, cut the legs of that bad socket or chip, then use a desoldering iron vacuum pump. Lets you get rid of each individual leg of the socket or chip without putting much stress on the pad and trace. Just a tip, not a must.
@hesed012
@hesed012 11 ай бұрын
Hi Adrian, I am a former owner of C64. I used it to create my college papers while I was attending the University of Guam in the 80s. It ran fine until the monitor was broken and I did not have your channel back then to learn how to fix it, so I threw it away all together. Watching your video took me back to thirty-eight years ago. Thanks.
@laurencevanhelsuwe3052
@laurencevanhelsuwe3052 4 жыл бұрын
It's fantastic to see how much love these old machines still get almost 40 years later. I just found my original C64 again after "losing" it for decades.. :-)
@forevercomputing
@forevercomputing 4 жыл бұрын
If someone says, "it's fine" TEST it anyway.
@Baerchenization
@Baerchenization 4 жыл бұрын
My mother said the radio of their stereo system stopped working. So I Ebay-ed them a replacement. When I finally went over to my parents' place this Xmas, it turned out the radio was perfectly fine and instead it was the amplifier that had stopped working :) So yeah, never listen to other peoples' diagnosis ! Her comment: she calls the entire stereo system " the radio". Cheers, mum :)
@MickeyMousePark
@MickeyMousePark 4 жыл бұрын
@@Baerchenization I worked in the computer hardware repair industry in the 1980's the first lesson they taught us was: Listen very carefully to what the customer thinks the problem is and what they think will fix it..after the customer leaves ignore everything they just told you... On side note our troubleshooting skills in hardware repair was make sure you have good power to the board then start at the CPU checking all input and output signals and work from there..we were lucky our schematics had OScope images of all pins of all logic chips on the board... 10 years later i worked at Microsoft internal IT (software) and first thing they taught us was: Listen very carefully to what the customer (these were MS employees) thinks the problem is and what they think will fix it..after the customer leaves ignore everything they just told you...
@someguystudios23
@someguystudios23 3 жыл бұрын
My dad is an electrician and he always says, "if someone says the circuit is off, test the circuit. ALWAYS TEST THE CIRCUIT."
@codprocamp4690
@codprocamp4690 3 жыл бұрын
Especially when she doesn't bring condoms
@kriswillems5661
@kriswillems5661 4 жыл бұрын
I am an electronics engineer and I think your troubleshooting was just fine. I liked that you used the scope. I am not sure I would have done as well as you. You're very experienced in debugging c64 hardware.
@keithwalter1241
@keithwalter1241 3 жыл бұрын
I have two solid years of electronics training and over 30 years of experience, and know very little about the C-64 inter workings, I own two, and used to program them in Commodore basic. You did an awesome job of troubleshooting the board, and had real tenacity in diagnosing each and every problem. You have better patience than I do. Very well done repair and video. I learned a lot about the C-64 watching your video. Thanks!!
@AZAce1064
@AZAce1064 4 жыл бұрын
15 years ago when I moved I gave away 2 Vic 20s , 2 64s cassette drive floppy drive monitor all cords software galore and even a printer to a friend who passed since then. I had packed all of it up in the 80s with foam, desiccant, and glad wrap in heavy boxes and stored it in closets for all those years. He said everything was working except the printer no ribbon or ink available and most of the cassettes and floppy’s had magnetic degradation. When he passed awayI hope his new wife found that stuff a good home and not the dumpster. This video brought back memories.
@adriansdigitalbasement
@adriansdigitalbasement 4 жыл бұрын
Oh that's great -- so much of it was thrown away. So a good home is a good thing.
@AZAce1064
@AZAce1064 4 жыл бұрын
Adrian's Digital Basement I wish I still had it now that my life long friend has passed away we used to be one of the first kids to ever have what they call gamer parties or something like that. When we were kids we would bring the whole setups to each others houses next door and program for days. Then we got dial up modems and typed messages back and forth. This was before internet.
@Ben-eu4il
@Ben-eu4il 4 жыл бұрын
I did not realize that "Total Novice" equaled Jedi Master electrical/digital Tech!!! Amazing sir! I have worked in computer software & hardware for 30 years. I found this very relaxing & appreciated your troubleshooting skills! Awesome job in your electrical trouble shooting!! Big LIKE & new Subscriber!
@pmgodfrey
@pmgodfrey 4 жыл бұрын
KZfaq: Do you want to watch this? Me: ...maybe? Very thorough diagnostic and repair. And now I forgot what I came to KZfaq for, but feel compelled to go get some C64's and fix them! Nice work!
@Kerveros1904
@Kerveros1904 4 жыл бұрын
Says total novice while the background behind him is full of electronics material, revealing a work of decades. Excellent video by all means, i was very happy to watch it. Definitely this is a material for a seminar in electronics.
@Kerveros1904
@Kerveros1904 4 жыл бұрын
@@adriansdigitalbasement you are very good with what you are doing and most important is that you are persistent, you do not give up easily. Too bad that all these bad c64s cannot be fixed by their owners because this is an expensive task as it could take several days even for an experienced electrotechnician.
@daibach5378
@daibach5378 4 жыл бұрын
wow this takes me back, back in the late 80's i used to fix these for a living, a repair company in Monmouth UK called Mills, cant remember having a cool diagnostic cartridge, but i can remember on blank screen faults removing all the top row roms and chips along side of it and using the game Jupiter Lander cartridge game, this game didnt need any of the top row installed and if it worked you knew the fault lay in the chips you had taken out, also piggy backing ram chips, sometimes you could find a duff ram chip by putting a new chip on top of the old one, (just squeezed on top), All this and you didnt need good eyes to work, now I am replacing tiny SMD stuff which i need a mag lamp, Nice work again mate, took me back 30 years with that video
@15743_Hertz
@15743_Hertz 4 жыл бұрын
Personally, I don't see all that many flubs with your repair. It takes a while to develop good practices for troubleshooting and different people use slightly different methods. You're doing just fine.
@TheBananaPlug
@TheBananaPlug 4 жыл бұрын
Agreed, no sure fire 'one best way', all repair guys I have known approach problems from different angles/perspectives.
@azzajohnson2123
@azzajohnson2123 4 жыл бұрын
We all learn from adrians learnings and that’s why we all find this so interesting to watch. We have all been there when troubleshooting.
@Spazilton1
@Spazilton1 4 жыл бұрын
From someone who has worked in Electronics repair for 20+ years in the private sector and the US Navy, your methods are just fine.
@ahndeux
@ahndeux 4 жыл бұрын
I saw one huge flub. He should have replaced that last botched wire job at 14:22. He fixed all the other wires and left one raggedy yellow wire. I was cringing when he left it on.
@Knaeckebrotsaege
@Knaeckebrotsaege 4 жыл бұрын
calls himself a complete novice, already has much better test equipment than what I'm dealing with... damn
@jeromeygreen4788
@jeromeygreen4788 4 жыл бұрын
I feel this in my soul
@stifledvoice
@stifledvoice 4 жыл бұрын
I got a free multimeter from Harbor Freight and barely enough smarts to follow a diagram to wire an arduino to a breadboard, so this guy is lightyears ahead
@borayurt66
@borayurt66 4 жыл бұрын
There is a saying which I strongly support in electronics, both for design and repair work: "If it works, it ain't stupid." Nice work!
@bswfcw
@bswfcw 4 жыл бұрын
I grew up fixing video games for arcades as a business in the early 80's. All professional arcade machines were designed and built like this. I developed the exact same skills you used to fix this on my own so you are spot on with your troubleshooting and diagnostics approach !
@siskodata
@siskodata 4 жыл бұрын
41 minutes just fly when you are watching something fun. Besides that why not make a tutorial for testing different components using different tools (multi meter. oscilloscope, probe etc...) I prefer it coming from a non technical person as my self then from an electronics engineer. Thanks and happy holidays.
@leandrotami
@leandrotami 4 жыл бұрын
I didn't realize that the video was that long!
@5Breaker
@5Breaker 4 жыл бұрын
*instant realisation* Wait what? That was 41 Minutes?
@snwdwg1
@snwdwg1 4 жыл бұрын
novice, are joking your the type of guy whose method gets written into tech journals. very good work
@garydunken7934
@garydunken7934 4 жыл бұрын
41mins of pure joy of fault diagnosis.
@Huzzahgamers_inc
@Huzzahgamers_inc 4 жыл бұрын
Good rule to stick to, If you see a bad socket... Just replace it. Clean up all your solder leads and make sure to double check all traces. * to remove bad sockets, if you can reach the leads, snip them all and then remove the plastic and then remove each snipped piece of snipped legs and clean and resolder the pads. ***But! I want to make certain to say, Great Job! It was a real treat to watch you work on that board and your logic about troubleshooting the issues was very well thought out. Good work and keep it up!
@Maxxarcade
@Maxxarcade 4 жыл бұрын
Gotta love working on a board that someone has messed with and pulled up traces. Having a good desoldering iron with the proper tip is essential to prevent trace damage. For most of my vintage boards, I use the Hakko A1002 nozzle with the 0.8mm diameter. And it's also important to maintain the pump and seals so you get enough vacuum.
@shawbros
@shawbros 4 жыл бұрын
The best scenarios are when you know who caused the problem(s), and after fixing the problems, you can explain them all to the person, so they realize their incompetence.
@nicepush2574
@nicepush2574 4 жыл бұрын
The 113 thumbs down were the previous owners of that CPU board 😂😂😂
@treadmillrepair754
@treadmillrepair754 3 жыл бұрын
I bought a damage Commodore 64 7 years ago and I fixied with my son, now he is a computer engineer. tgis video bring back memories. Best Regards.
@jjock3239
@jjock3239 9 ай бұрын
I enjoyed watching you struggle your way through the repair, simply because someone had butchered the motherboard. I particularly liked your logical approach, and your perseverance. It all paid off..
@anotheruser9876
@anotheruser9876 4 жыл бұрын
"Look How They Massacred My Boy" Good job on reviving it.
@Hertog_von_Berkshire
@Hertog_von_Berkshire 4 жыл бұрын
Desoldering can be a real pleasure with the right tools. I worked with a guy who was a total expert at it. He swore by braid, and modestly quipped that he learned to desolder from the need to undo lots of his own work.
@disgruntledtoons
@disgruntledtoons 2 жыл бұрын
When I first trained as an Air Force electronics maintenance technician in 1984, we were still troubleshooting problems down to the component level, like we see in this video. Within a decade we troubleshot down to the circuit card only, and we did not repair them; we went the card to supply and in time we received a replacement. Back when the C64 was a new machine, this much time to repair a defective unit was not economical; it was cheaper to simply throw it out and buy a new one.
@PeowPeowPeowLasers
@PeowPeowPeowLasers 4 жыл бұрын
"piece of crap socket" - **looks nervously at the sockets I've installed in my PET**
@raven4k998
@raven4k998 4 жыл бұрын
heres a pat on the back it'll be fine my brother it'll be fine don't worry
@hullinstruments
@hullinstruments 4 жыл бұрын
AUGAT brand sockets my man!!! They are the best! Usually $5-$15 each but if you watch eBay you can get some deals. I just bought a lot of 20 beautiful gold plated brand new in the package AUGAT sockets for $7 shipped! There a special type, and I could flip those bad boys for $15 each but I’ll hold onto them! I love collecting vintage IC and transistor sockets. There are some really beautiful examples out there that bring crazy money.
@sivalley
@sivalley 4 жыл бұрын
Can't blame yourself if you don't know better!
@jeromeygreen4788
@jeromeygreen4788 4 жыл бұрын
Can't be that bad in the grand scheme of things, I fix cars and motorcycles as a hobby and the amount of dirt cheap, questionable components that I've used on them with no issues is amazing. If you can convince it to work where it's supposed to the majority of the time it just works, no matter how jankey it is.
@Calphool222
@Calphool222 4 жыл бұрын
Some people say double leaf sockets, but I say machined pin is the way to go. I've used thousands of them, and *never* had a problem with machined pin sockets. Double leaf sockets aren't *terrible*, but I've had a few get crusty and fail. Single leaf sockets are the devil and should never have even been imagined.
@360hikes8
@360hikes8 4 жыл бұрын
My Dad bought his C64 when I was about 4 years old. I'm 40 now. He still has it and it still works. It's never needed serviced or repaired.
@adamw.8579
@adamw.8579 4 жыл бұрын
These was good times when "programmed wearing" was unknown term. Proper engineering and equipment was made for years (sometimes for decades).
@jimviau327
@jimviau327 4 жыл бұрын
If it is true that you have no experience in electronic and you can demonstrate this level of intuition and intelligence you definitely have a gift. I have seen electronic engineers not able to come close to that level of expertise.
@UltromanTheTacoman
@UltromanTheTacoman 4 жыл бұрын
I don't know anything about hardware repair and I only ever played a C64 once in my life, not really connecting with it, since I had my Sega MD 2 already...and yet, I can't stop watching. I guess I just love watching people who know their craft do what's magic to me :) And also, I admire people who resort to fixing things instead of just buying new things. It's not like I'm a "no waste" person, but there's a happy middle-ground where you at least TRY to fix, e.g., the ripped pocket on your jacket, instead of throwing it out.
@area73blog
@area73blog 4 жыл бұрын
This was like watching a very gripping 41 minute mystery show. Great work!
@MattsCreative
@MattsCreative 4 жыл бұрын
jesus just saw it was 41 mins long but felt like 10 mins wow nice work
@lutzweb
@lutzweb 4 жыл бұрын
Best moment when you say, I am an electronic NOVICE (you are not)... and you guess that emittor and collector should not be shorted together! you are great guy, well done this resurrection of that glorious c64 board
@rivlezz
@rivlezz 4 жыл бұрын
I'm 37 and grew up with a C64C. You make me want to buy another C64. Great video man, I thoroughly enjoyed it.
@Jerkwad152
@Jerkwad152 4 жыл бұрын
Your videos are always an education.
@Jerkwad152
@Jerkwad152 4 жыл бұрын
Yes, I think so. :3
@jbucata
@jbucata 4 жыл бұрын
@23:42 "So to recap..." Me: "Oh, you're going to replace all the capacitors next???"
@raygud
@raygud 4 жыл бұрын
a lot of leaking capacitors there...
@samuellourenco1050
@samuellourenco1050 4 жыл бұрын
The machined sockets are much better than those that were used on that poor C64. Anyway, great troubleshooting!
@brooknet
@brooknet 4 жыл бұрын
A great bit of detective work - very entertaining. It's almost as if the faulty '64 has a mind of its own and is thinking "right, what trick can I pull now to get this guy to give up?"
@SteveJones172pilot
@SteveJones172pilot 4 жыл бұрын
"This socket is a piece of crap!" - Yeah.. as soon as you pulled that chip, I said the same thing in my head.. I hate those sockets too!
@throttlebottle5906
@throttlebottle5906 4 жыл бұрын
they cause more issues than they fix, I've had to remove many from all sorts of equipment a bad one is 8 pin op-amps in amplifier early stages, had them go intermittent and drive output stages to near full DC rail voltage and cook speaker coils!
@SteveJones172pilot
@SteveJones172pilot 4 жыл бұрын
@@throttlebottle5906 Interesting! I hadn't considered a scenario where a failure like that could cascade to another failure but that's a good thing to remember! I generally run into them on old vintage arcade machines (PacMan and Williams pinball machine boards, specifically..) where it may cause something not to work, but I've never seen it break something else!!!
@mikeh4775
@mikeh4775 4 жыл бұрын
I own a Donkey Kong arcade machine and have had issues with IC sockets as well
@andyknowles666
@andyknowles666 4 жыл бұрын
I was out of ideas before you were 5 minutes in.
@Jim-sq9mq
@Jim-sq9mq 4 жыл бұрын
I've repaired thousands of C64 motherboards in 80's and that was just painful to watch. Lol. Glad you finally got it working.
@johnpossum556
@johnpossum556 4 жыл бұрын
You've got the best skills to do effective troubleshooting. Sheer tenacity and mental focus. Also, like a Dr you do no harm. The fact that you diagnosed & repaired it down to the component level of even components you don't know proves that. And this comes from some one who was trained in one of the best electronic colleges in the country. Most troubleshooting comes down to two methods. Divide & conquer. Or signal tracing. The largest percentage of repairs are mostly PSUs and what you did was much more complex.
@Aruneh
@Aruneh 4 жыл бұрын
I have never cared for Commodores, growing up at the tail end of that era, but this video was very interesting! Good job getting it working right.
@joeyr9876
@joeyr9876 4 жыл бұрын
My gosh you were determined to get that fixed. I think my patience would have given out quite awhile in to the project and I would have declared it a parts machine. Good job!
@deltekkie7646
@deltekkie7646 4 жыл бұрын
Good video. I run an R&D lab where we build electromechanical test equipment. I mentor Electrical Interns often and also have technicians who work for me. One thing I train my people to do when they are troubleshooting a problematic circuit board is to use a known good board, save the scope image of the different signals for the data lines you need to troubleshoot to a library on your PC. This way when you are troubleshooting the bad board you need only to pull the images up for the pins to see what the data lines SHOULD look like to know if what you suspect is bad is correct. This has saved me a lot of time over the years.
@peterromano1911
@peterromano1911 4 жыл бұрын
Wow, what a walk down memory lane !!! I started my electronics career in the early to mid 1990s and my first gig was working for a Commodore Dealer. Since I was good at soldering, the owner made me his #1 troubleshooting tech for C64 and Commodore Amiga computers. It has been so long since I have toyed with any of these computers but your video brought back a lot of memories and your techniques for troubleshooting were great !!! Yes, A diagnostic schematic is a Tech's best friend ALWAYS !!! I would love to watch more videos like this !!! Thank you for the memories ! Pete...
@Turnbull50
@Turnbull50 4 жыл бұрын
I ended up watching for the whole length waiting with baited breath each time you switched the power on.
@CraigAB69
@CraigAB69 4 жыл бұрын
It is interesting to see that the test harness, whilst very useful, can only go so far. Then you are back to reading the schematics. Thank you for reminding me of the important lesson of looking at the board first for 1) Broken traces 2) Bad/broken/dry solder joints. It is just so easy to jump in and start de-soldering components.
@stefanocrespi5424
@stefanocrespi5424 4 жыл бұрын
@@adriansdigitalbasement but it wouldn't have given us a full 41 minutes long good entertaining!
@OldAussieAds
@OldAussieAds Жыл бұрын
I had a black screened C64 that I was researching how to fix. I ended up taking it to a guy who swapped out the whole main board, due to the original board having too many chips blown (He in turn would have salvaged the working chips from my old board for future repairs). I now know that if I had have attempted the repair myself, I would have torn my hair out and probably would never have got there in the end. This video solidifies my thoughts.
@Twigleaf
@Twigleaf 4 жыл бұрын
My Winter AC went out. I was told to come to this video. Was told these things would double as a heat furnace during Winter. Heat up house very fast.
@Alexis_du_60
@Alexis_du_60 4 жыл бұрын
Oh dear, this poor Commodore sure has seen better days, it's always satisfying to see a machine fire up and just work after you spend countless hours tackling its problems. ------------------------------------------------ Aye, while it's not as impressive, I too, got my hands dirty and started tackling a project: my friend's Amstrad CPC 6128, it won't read any disk, and the floppy drive makes weird noises... And it has a intermittent fault where the keyboard intermittently stops responding. For now, I've dismantled the drive and found out that the belt is gone (it has melted away, and trust me, cleaning melted rubber is a pain, thankfully I had rubbing alcohol on hand, it more or less worked fine), for now I haven't put it back and will need to order a new belt. After that I'll move onto the keyboard issue...
@ct92404
@ct92404 4 жыл бұрын
Yikes! It sounds like you definitely have a lot of work ahead of you! It's great though that people are fixing vintage computers and bringing them back to life. In a way, it definitely is helping to preserve a part of history.
@Alexis_du_60
@Alexis_du_60 4 жыл бұрын
@@ct92404 yeha in a way, it feels like restoring preserving a ancient artifact from the past, so it doesn't fade into the abyss of the forgotten things. That aside, this Amstrad is quite a simple machine, it's just yet another Zilog Z80-based computer, nothing too far-fetched, they were built to be cheap (from what I heard about them), but surprisingly the one I'm restoring has held up pretty well (save for the drive belt melting and the keyboard ribbon connector being flaky), though on the outside it's near mint, save for a few blemishes, but hey, it adds a bit of character to the machine, right?
@ronniepirtlejr2606
@ronniepirtlejr2606 4 жыл бұрын
I enjoyed watching you diagnose this computer. I am also a novice at Electronics. I would say you are about a year ahead of me or so. I have learned quite a bit by watching you. I've noticed that the schematics are starting to look a lot easier to me. (they make a lot more sense). I would imagine as with any new language, it all seems overwhelming at first, but after a while things just start falling into place! :-)
@wa4aos
@wa4aos 4 жыл бұрын
Just a few comments. I owned a PC shop in Charlotte NC in the 80's and did component level work on MANY types of computers and peripherals. I suspect I and my employees, repaired more than 500 Commodore boxes, mostly C64's but also some VIc 20's, C128's and others. The C64 was a great unit and provided a lot of bang for the buck back then. A business associate turned me on to the AIRVAC handheld desoldering tool and the day we got the first one was a fantastic day. The tool required a shop compressor which turned ~90psi to ~20" of vac at the tip. For removing IC's and sockets it was so good, often just turning the board upside down, the IC would fall off. We took time each day to clean out the solder trap and it would work very well for the day. I still have several of them in my lab. Once the trap starts getting about half full, the performance drops quickly. I also have a Hakko which is better for larger ground planes but for IC's, transistors the AirVac is outstanding.. They are still sold, not cheap but it will pay for itself quickly. You should remove the shorted zener diode since it will be pulling current and heating up. Here is the link for the AirVac tool I use. Oh, keep an eye on ebay for used units at a lower price. www.air-vac-store.com/mm5/merchant.mvc?Screen=CTGY&Store_Code=AS&Category_Code=PVSG Regards, Glenn DSM Labs
@samsta10000
@samsta10000 4 жыл бұрын
"It's fixed!!" "Oh wait no it's not." "There that's it working!"" "Hahaha nope." "Alright, finally, it's working!" "Hahahaha think again!" That's some incredible dedication to fixing things you have. Great job!
@bonuscreature
@bonuscreature 4 жыл бұрын
Enjoyed this immensely. I would attribute your aversion to novice status to the Dunning-Kruger effect. Bookmarked The Pictorial C64 Fault Guide. Hopefully it will help with my C64 character ROM issue.
@leandrotami
@leandrotami 4 жыл бұрын
Don't you mean the imposter syndrome? This is a case of a person who clearly knows what it's doing but is saying otherwise. Still... as any expert on any field keeps learning new stuff, they become more and more aware of all those things that they ignore. Therefore you have Socrates there saying 'I only know that I know nothing'.
@bonuscreature
@bonuscreature 4 жыл бұрын
Leandro Tami Dunning-Kruger effect is about both novices overestimating their ability AND more knowledgeable people underestimating theirs.
@FakeButt
@FakeButt 4 жыл бұрын
Great video! I usually watch random electronics repair videos late at night so I can fall asleep but I had to pause yours and find another one to watch last night because it was so interesting :) I watched it today and subscribed.
@matsnilson7727
@matsnilson7727 4 жыл бұрын
Impressive! A lot of comments have already mentioned the "novice" thing, but I would probably describe you as a magician when it comes to this stuff. My knowledge completely ends with knowing it requires electricity to run.
@JAHomeRenos
@JAHomeRenos 4 жыл бұрын
Nice repair. You know it's funny how many people these days think Mario's first appearance was in super mario for nintendo but they completely forget it was actually Donkey Kong.
@earthlydescent
@earthlydescent 4 жыл бұрын
You may go around things differently, but you're my favorite KZfaq channel. Folks like you, LGR and the 8 Bit Guy are the best. Merry Christmas and Happy New Year to you.
@happyday2678
@happyday2678 4 жыл бұрын
Adrian was trying to be humble but the effect of that humorous "total novice" depiction likely sounds too detached from the stunt so much so that 98% of his audience would be left feeling they don't even qualify for the title of "novice" anymore.
@Ben31337l
@Ben31337l 4 жыл бұрын
I think that amateur might be a better description for us common folk.
@chriskarson4881
@chriskarson4881 3 жыл бұрын
I'm not buying the "I'm a novice" schtick. Adrian you are a very good troubleshooter and very humble...
@wynandmentz9532
@wynandmentz9532 4 жыл бұрын
You give yourself way to little credit and I have repaired similar Atari Products in the 80's myself. Nothing wrong with your troubleshooting skills and you are NO novice. Well Done- that was great to see it all come alive. Best for the future.
@abar1120
@abar1120 4 жыл бұрын
This video was amazing! Your tenacity during the troubleshooting process was very impressive. If you are at all interested in attempting to repair a faulty Atari 1040 STf please let me know. I've had the machine for about 1 year and can't get video to display. Big fan of your videos!
@brianv2871
@brianv2871 4 жыл бұрын
Have you picked up the Diagnostic cartridge? I think BEST sells one, which is where i got mine. I ended up having to just pick up another 1040STF and do chip swapping.. once you figure out the chip, you can just resell the 2nd computer on ebay. With my 520ST that couldn't display video, I ended up replacing the C025914-38A chip. You're using the original monitor, I assume?
@abar1120
@abar1120 4 жыл бұрын
@@brianv2871 Thank you for the advice. I don't have the diag cart. I always figured the issue would be the Shifter chip or the glue chip. I actually have a working Atari 520 STf but have always been weary to swap the chips as they don't look identical to what I see on the 1040STf and didn't want to risk damaging components from my working system to test the 1040. I don't have the original monitor but do own monochrome and color VGA cables that works with an Acer monitor capable of the 15khz refresh rate. This of course has been tested on the on the 520. Thanks for the advice!
@brianv2871
@brianv2871 4 жыл бұрын
so my two boards, the chips were slightly different as well, but googling i determined the parts were just newer revisions (something like 30 vs 30a). But yeah, i guess do what your comfortable with, but the 520stf and 1040stf were essentially the same machine but with more ram. in fact, my 520stfm had empty slots that could be filled to make it a 1040. I never bothered with that since i used to have a ram module that stopped working and might just get or make another one at some point. I only asked about the monitor because I've not had luck using the special cables (like composite, or the scart cables) on non modulated ataris, but i assume if your setup works on a non modulated Atari then you're good there. Anyway, don't think Adrian could really help on this, because even if he could diagnose the issue, he'd need parts to swap in, and he doesn't really have spare parts for them like he does commodore. If i recall, he just has the STE, which has different chips.
@markwanklyn4195
@markwanklyn4195 4 жыл бұрын
@@abar1120 no video output is not necessarily a video fault - my STe had no video output and it turned out it was the reset circuit that was at fault -bad output on the 555 timer chip was causing the reset line not to be toggled correctly on power up
@PCBoardRepair
@PCBoardRepair 4 жыл бұрын
@@brianv2871 chip swapping is just guessing
@PeteSauerbier
@PeteSauerbier 4 жыл бұрын
I really like your style in progressing with the diagnostics and I'm glad there's still good care for those hardware gems!
@ozComputerguy
@ozComputerguy 4 жыл бұрын
Goodness gracious, that brought back some memories, and stuff I’d absolutely forgotten. As a young lad I remember the first trading day after Xmas. A long line up of c64 owners with c64 cassette decks in their hands. That was me all day aligning cassette decks and watching pavloaders flash at me. I’m sure it has had some effect ! Yertt! I can’t imagine my kids ever waiting for 14 minutes for a game to load. Poke 53280,1 and sys64738 to you all!! Wow that’s like 35 years since I typed that last.
@thunderbolt10031
@thunderbolt10031 4 жыл бұрын
This video was 41 mins long? Geez I didn't think it was nearly that long. Good work dude, that was very entertaining and informative!
@Steve_R
@Steve_R 4 жыл бұрын
Thank you Adrian for bringing another C64 back to life. Thanks also for taking the time to make these videos for everyone to enjoy. Merry Christmas to you and may 2020 see more repair and other videos from you. Steve.
@unaphiliated5090
@unaphiliated5090 4 жыл бұрын
It was pretty common for the RAM chips to fail. I remember doing lots of those back when I worked for a school board that had hundreds of C-64s
@Ernie-Tech
@Ernie-Tech 4 жыл бұрын
Unbelievable that C64 is still so much around among people. And then even putting so much time and effort in, wauw. Eventhough I see you using ESD safe mats for your cmos-chips, I don't see you wearing any ESD-wriststrap while you do wear polyester-based clothing?! Or maybe the strap is on your ankle :-) So recognisable the ups and downs during repairs. I've worked for 9 years in a repair centre, going through this each day. Fun part of this 80's tech is that it is still perfectly understandable and repairable, in contrairy with modern SMD-components and the impossibility to obtain circuit diagrams. Thanks for sharing this experience on YT
@clairsmyers3571
@clairsmyers3571 4 жыл бұрын
Adrain, I have been in electronics repair most of my adult life. I see nothing wrong with your techniques! What works for you is what you want. I have repaired many C 64s with just a logic probe and I really like the equipment you have there. Very impressive.
@EngineeringVignettes
@EngineeringVignettes 4 жыл бұрын
I never liked that cassette high-side switch circuit. When I was a lil un using my C64 with a data-cette, I had at least two repair visits that I remember having to take the computer in to get the transistor replaced. When I went over to disk drives that issue was effectively bypassed. I imagine nowadays that the high side switch is akin to an appendix on a C64. Seasons greetings, thanks for the content from 2019. Cheers,
@ulfen92
@ulfen92 4 жыл бұрын
Makes me wonder why they didnt use a PNP transistor instead as a switch. That would have made more sense in that highside switch circuit.
@EngineeringVignettes
@EngineeringVignettes 4 жыл бұрын
@@ulfen92 - Thats' a good point. I think the NPN was used as the circuit acts also as a linear voltage regulator. The zener on the base ensures that the emitter voltage is clamped at .6v below the zener voltage. This helps to roast the transistor causing it to fail as there is no heatsink on it. -_- Cheers,
@lwilton
@lwilton 4 жыл бұрын
That TO-66 is a pretty husky transistor for the purpose it is used for. My experience was that the cassette drive would get plugged on incorrectly or an aftermarket cable would short the output of the transistor to ground and fry it before the 9V fuse went.
@zordmaker
@zordmaker 4 жыл бұрын
Fixed. Now give the customer the bill for around $2k of time... and BTW, no warranty... thank goodness I'm not in to heritage electronics repairs... anymore...
@FrankConforti
@FrankConforti Жыл бұрын
Adrian, thank you for taking us on this journey. Your diagnosis methods are just fine. As I’m sure you know, there is seldom a mapped out troubleshooting guide that will cover all potential faults especially when stacked up like this board. One of the most expensive aspects for NASA and Military projects is the need to reduce fault isolation as much as possible even if there’s only a once in a million chances the fault condition will occur. Working on commercial products is all learning the obvious weaknesses, and a strong sense of intuition. I see nothing wrong with your methods. Teaching them to others especially while showing all the ugliness builds that intuition. Thanks again!
@ForaPhil
@ForaPhil 2 жыл бұрын
You're probably better than most professional electronics repair engineers, and when it comes to the C64 you probably know more than the original designers of the board, so I wouldn't exactly call you a novice.
@FalconFour
@FalconFour 4 жыл бұрын
TS100 tip: if you've got the XT60 to DC barrel cable that's commonly offered with the TS100, that cord is a piece of junk. The wires in the cable are awesome, but the strain relief is bad - it makes the wires fray and break with moderate use. Check for continuity in the DC barrel while manipulating the strain relief. You might need to strip the molding off it and resolder, hot-snot the thing back together. Maybe.
@0xbenedikt
@0xbenedikt 4 жыл бұрын
Hmm, I also had my TS100 power jack go bad, but it was the wallwart Sainsmart one. I've since replaced it with a JBC Compact iron, but I would still like to fix the old TS100. Perhaps I might try bending the lever in the barrel jack a bit inwards.
@Rumteldat
@Rumteldat 4 жыл бұрын
I can't believe I watched the entire video. I found it fascinating and really informative. Great job!
@bullettube9863
@bullettube9863 4 жыл бұрын
Nice work! I remember I used to use a rubber ball suction tool to remove solder and it took hours to make sure I had completely cleaned a connection. Another trick I used was a steel wire that I wound around my soldering pen to make a very tiny tip to clean out socket holes. My son and I used to play games on his Commodore 64 and had a lot of fun together. The main problem I used to encounter was flimsy connections that I had to resolder. My son now works in IT but still remembers the fun he had in simpler times.
@graynoble4795
@graynoble4795 4 жыл бұрын
HOLY CRAP MAN! I loved (LOVE) my old Commodore 64 that has been dead for over 25 years. The sound doesn't work and the 1541 drive doesn't read, but I do get the blue ready screen. I have never seen any tutorial like this and I was fired up after seeing you do this! Your skills are off the hook and you make this look SO easy! I know its not and would never attempt this type of repair at my level (or lack thereof) but this was absolutely fascinating to watch! Thank you!!!
@davej3781
@davej3781 4 жыл бұрын
I was an Atari guy back in the day... why am I watching 41 minutes of a guy repairing a C64? at 1am?
@adamw.8579
@adamw.8579 4 жыл бұрын
Me too, my first serious overhaul was expanding RAM in my Atari XE to 256kB for Sparta DOS RAM-Disk. Works lika a charm for few years until PC come on my desk.
@davej3781
@davej3781 4 жыл бұрын
I don't recall doing any hacking on my 800, but I did hack and ultimately killed my 520ST. First I separated the keyboard from the rest of the computer, because I hated having all the cables stretched across my desk to where I wanted to have the keyboard. Initially I just had the keyboard in the empty case connected by a small cable to the mainboard at the back of the desk under the monitor stand; I planned to cut the case down to a more proper keyboard size, and then put the mainboard back into what was left... Never got to it though before I killed it doing a memory upgrade with some bad solder from radio shack. Then I got a Mega ST2...
@VTX00128
@VTX00128 4 жыл бұрын
Ah this take me back to my 386/486 chipset days
@dirtydon8661
@dirtydon8661 4 жыл бұрын
Time for a backup solder station. I deal with removing IC’s and have used your hot air method. Lifted/ripped traces will test patience. Enjoyed this video as it covered several Troubleshooting techniques.
@matthewhapp8688
@matthewhapp8688 4 жыл бұрын
yo i am an electrician and you are doing a fantastic job keep them old classic computers ticking
@jimtalor7971
@jimtalor7971 4 жыл бұрын
Those were the days, I loved my C64 back in the 80's upgraded to dual floppy drives and added some sort of turbo switch. The games and music ( Ultima series) kept me entertained for hours, had to curb that when the old lady told me one night you better come to bed or I will cut off your keyboard....
@tron3entertainment
@tron3entertainment 4 жыл бұрын
34:57 "Bring in the Logic Probe!" - Sark / TRON
@leokimvideo
@leokimvideo 4 жыл бұрын
Thank you for saving my childhood. Imagine if these were ROHS, then there would be no way of getting these to be alive again. I stopped putting my failures in videos because I feel KZfaq saw them as demonetization issues. Mind you they never tell you why your video is demonetized. Funny how some people don't say the 'L' in soldered. Maybe I'm saying it wrong.
@SonicBoone56
@SonicBoone56 Жыл бұрын
We Americans tend to drop the l in soldering.
@Talisman-tb6vw
@Talisman-tb6vw 4 жыл бұрын
I used to run a job shop where we built prototypes for engineers, and we did a lot of repairs. We were one of the only handful of shops in the world that could unsolder a BGA by hand, and resolder it - by hand. I Loved showing off the skills of my crew to nay-sayers. :)
@rOSScOGITANS
@rOSScOGITANS 4 жыл бұрын
very good work, you are the example that a computer it's not only chips and circuits, it's a memory of an age, it's your childhood, it's connected with emotions and feelings like an old good car :)
@pilotkid2011
@pilotkid2011 4 жыл бұрын
This was easily the best video you have ever made 10/10
@srensrensen5354
@srensrensen5354 4 жыл бұрын
I might just be a geek :-D But even though I have spent ages online, watching all kinds of videos, this video is one of the most interesting and satisfying videos, I have seen
@parishna4882
@parishna4882 4 жыл бұрын
That was my impression also. It was good to see an actual diagnostic video test, rather than someone who just knows and thinks the viewer knows so they omit anything that actually helps us newbs understand these things. Nice vid Adrian!
@GregMcCarthyUK
@GregMcCarthyUK 4 жыл бұрын
Great video. Poor C64 was abused by other people that don't know to do proper repairs. Its great to see you bring it back to life.
@SteveGoodenough
@SteveGoodenough 4 жыл бұрын
Just watched 42 mins and was totally engrossed, I would never call you a novice! Looks over at my dead 64, wish I had someone like you round the corner :D
@moominpapa1980
@moominpapa1980 4 жыл бұрын
"I'm an electronics novice"- made me spit out my wine 😅🤣
@tindrli
@tindrli 4 жыл бұрын
same here
@kataseiko
@kataseiko 4 жыл бұрын
I think someone had that character ROM issue when they invented the Ancient script for Stargate.
@stevesstuff1450
@stevesstuff1450 4 жыл бұрын
Ohh man... what a great repair job! Fantastic! Another C64 has risen from the grave! Brilliant! And thanks for showing that clip of the recent Donky Kong remake; I had no idea it existed... just downloaded it and have it playing now on my new "TheC64" 'maxi'/full-size machine.... that music remake from Donkey Kong Country is astoundingly good..... amazing use of the SID chip, and this new machine plays it back brilliantly too - it's great emulation ! Great video, and great repair job... Hope you've had a good Christmas... and thanks for this video :-)
@stevesstuff1450
@stevesstuff1450 4 жыл бұрын
@@adriansdigitalbasement : Yes, it is, and it's a brilliant 'retro' game...the new 'TheC64' is a great repro version, and works pretty much identically to the original... I got mine a few days ago and love it! It's like having the original 64 back after all these years...apart from the lack of the original ports on the back - which is understandable with what they were trying to recreate..... ;-) The new 'TheC64' has full access to virtual tape, cartridge, and disc based programmes, all via the USB ports, and so is a brilliant device for those of us like me, who want to relive old memories of the original, and want to carry on using the system in a modern way; I wonder if adaptors will ever be made to convert the old ports to the USB standard? Could be cool!! Galencia is a wonderful new game and runs perfectly on the 'TheC64', and as with the Donkey Kong Country - that theme tune is just amazing!!
@asphixmx
@asphixmx 2 жыл бұрын
I am a C64 fan. I know nothing about electronics, but I saw all your 41 mins video and found it very interesting. Thanks!.
C64 Repairathon! Part 1 - Intro and black screen on #1
19:18
Adrian's Digital Basement
Рет қаралды 56 М.
Don't use a blowtorch to fix your C64!
40:17
Adrian's Digital Basement
Рет қаралды 80 М.
КАХА и Джин 2
00:36
К-Media
Рет қаралды 4 МЛН
100❤️ #shorts #construction #mizumayuuki
00:18
MY💝No War🤝
Рет қаралды 20 МЛН
Pray For Palestine 😢🇵🇸|
00:23
Ak Ultra
Рет қаралды 31 МЛН
Fixing two C64 motherboards with hot chips
36:03
Adrian's Digital Basement
Рет қаралды 85 М.
Fixing a Commodore 1541 Disk Drive
30:23
Adrian's Digital Basement
Рет қаралды 118 М.
What's keeping this Apple IIc from working?
43:48
Adrian's Digital Basement
Рет қаралды 238 М.
The Evolution64 - Is it worth the money?
15:15
The 8-Bit Guy
Рет қаралды 460 М.
"Left for dead" Commodore 64C made beautiful again!
18:33
Adrian's Digital Basement
Рет қаралды 176 М.
Improve your C64's video output with this simple fix
38:51
Adrian's Digital Basement
Рет қаралды 73 М.
How to fix an 8-bit computer with only cheap tools
52:54
Adrian's Digital Basement
Рет қаралды 107 М.
Rebuilding A Commodore 64 Power Supply
47:35
Retro Hack Shack
Рет қаралды 13 М.
What's Going On With This C64 PSU?
18:32
Noel's Spare Parts
Рет қаралды 8 М.
Can you build a brand new Commodore 64 from (nearly) 100% new parts?
20:49
Выложил СВОЙ АЙФОН НА АВИТО #shorts
0:42
Дмитрий Левандовский
Рет қаралды 1,3 МЛН
What’s your charging level??
0:14
Татьяна Дука
Рет қаралды 7 МЛН
Pratik Cat6 kablo soyma
0:15
Elektrik-Elektronik
Рет қаралды 8 МЛН
3.5.A Solar Mobile 📱 Charger
0:39
Gaming zone
Рет қаралды 319 М.