AEM AFR/Boost Gauge Install

AEM AFR/Boost Gauge Install | Ep 21

Рет қаралды 27,321

6 жыл бұрын

Hello Everyone, in this episode of the build I demonstrate how to install the AEM wideband failsafe gauge. This is a combination gauge for Air Fuel Ratio (AFR) and Boost Pressure. Please see all relevant links below and as always if you have any questions about the install don't hesitate to ask.
AEM Failsafe Gauge: a.co/5bdBF7E
Gauge Mount: a.co/cxx6OrA
AEM Software Downloads
1) Failsafe Config Software
www.aemelectronics.com/product...
2) AEM Data Log Software
www.aemelectronics.com/product...
___
Video Gear: kit.com/Rotary_Knight/my-came...
Desk Setup: kit.com/Rotary_Knight/my-desk...
Garage Tools: kit.com/Rotary_Knight/my-favo...
FC Parts For Sale: tinyurl.com/y6q2tkt5
___
/ rotary_knight
___
This video and description contains affiliate links, if you click on one of the product links, I’ll receive a small commission at no cost to you. This supports the channel and allows me to continue making more videos. Thank you for your support!

Пікірлер: 43

@mparavagna 5 жыл бұрын

I feel that your demonstration/how to is leagues above many that are out there. You are thorough, yet you don't beat it to death. Your editing shows that you put forth a respectable effort, and the end result is superb. Much respect..... Subscribed. Thank you.

@AlexFranceschi 5 жыл бұрын

Thank you for the feedback! I definitely appreciate it. Looking forward to getting back to work this month on the project.

@BOOS7ED_S2K 5 жыл бұрын

great video helped me out alot thanks

@bmorlok84 2 жыл бұрын

So on the page following the wiring diagram it discusses the pins on the connectors, and in states the brown wire, if not being used with an ems data logger should be connected with ground for best gauge readings. Wondering how true that is?

@goodtogaz 5 жыл бұрын

Hey, I have that same desk! Good stuff, Lol

@rivercitytee6828 3 жыл бұрын

Great video! Just wish you had shown the actual gauge while running...

@AlexFranceschi 3 жыл бұрын

I still have much to learn as a "youtuber" lol, slowly I'll get there. thanks for the feedback!

@kankam4819 2 жыл бұрын

Just wondering where did you tap your safe wire to?

@G_Rapids 3 жыл бұрын

Is there a way to use the failsafe ground without a datalogger? I've seen examples where if your AFR exceeds your high side limit, it will cut your ignition and shut off the engine which is something im looking to do.

@AlexFranceschi 3 жыл бұрын

I haven't looked into this to be honest. However, you need some form of feedback or control into the ECU. Either via a stand alone ECU or something like an AFR controller that can do this. I can only monitor my AFRs with this gauge and it's up to me to make sure my fuel system is designed to supply enough fuel and if I see things going bad I have to manually kill the engine. My setup is very conservative though, so I am not too worried about this. One day I'll go stand alone but for now I'm still OEM.

@theLastHuff Жыл бұрын

What does wiring up to “rpm” do? What function does that serve?

@AlexFranceschi Жыл бұрын

That's to monitor the engine's Rotations Per Minute (RPM), that gauge can monitor/record it.

@shoz8635 6 жыл бұрын

Nice, video Alex. Wondering does the faceplate light up. When you hook up the grey wire to the dimmer? Just curious.

@AlexFranceschi 6 жыл бұрын

David Vang sorry for the delayed response. I had a busy weekend. The faceplate itself doesn't have a backlight. The lights that adjust brightness are the center number display and the bar display. Unfortunately the faceplate numbers don't light up. Hope that helps!

@NickEnglishPhotography1 5 жыл бұрын

Would this gauge work with just 12v connection and ground wiring? I have an existing boost gauge which I'd love to replace with this and not need any additional wiring splices. Currently it's got a yellow 12v and black GND connection. Obviously I'd need vacuum and lambda too... But purely from a powering on point of view, would that work?

@AlexFranceschi 5 жыл бұрын

Sorry for the delayed response. It should work. Just make sure your 12V source is a switched IGN source. Also, you may have lights on the gauge but will not be able to control the brightness of the gauge.

@cesarbarrese 6 жыл бұрын

Hello Alex! El diplay de mi AEM no funciona... si la wideband de leds... Pueder ser porque conecte el grey wire a 12 v??? O simplemente compre fallado el reloj? Tendra arreglo?

@octane_media Жыл бұрын

Hey! I know this video is a little old I am running a megasquirt ecu in my Datsun and it requires a 0v-5v input from the gauge this would be the white wire on AEM correct?

@AlexFranceschi Жыл бұрын

Sorry, it's been ages since I've looked at the diagram but that does sound right, just double check and don't hesitate to contact AEM for more help. The gauge has an output for stand-alones like yours.

@octane_media Жыл бұрын

@@AlexFranceschi thanks for the reply ! I’ll have to call them and double check on that have a wonderful evening!

@AlexFranceschi Жыл бұрын

@@octane_media Absolutely, likewise!

@Analyzer52 4 жыл бұрын

Does it have an led light at night to see the boost gauge? Several say that is its main flaw you cant see it during night driving.

@AlexFranceschi 4 жыл бұрын

It lights up at night, no problem at all. I can't recall off the top off my head if the white numbers light up, but I have the gauge programmed so it turns from green to yellow to red if the boost gets too high. So, it doesn't matter anyway.

@Analyzer52 4 жыл бұрын

Thanks

@Jordan_B34 Жыл бұрын

Can I program it to see only boost in the middle? Also if I don’t install it to the dimmer will it be too bright at night?

@AlexFranceschi Жыл бұрын

Sorry for the delay, yes you should be able to change the center display for boost, it comes with additional faceplates. The dimmer does help at night but it's not that bright as-is tbh.

@Jordan_B34 Жыл бұрын

@@AlexFranceschi thanks for the info. I’m under the assumption the gauge can be calibrated via the AEM app?

@AlexFranceschi Жыл бұрын

@@Jordan_B34 Yup, that's correct.

@davidwhite4837 3 жыл бұрын

Hi Alex, Just bought one of these and I was just wondering the wires you capped off do those go into the ecm ? thanks, Dave

@AlexFranceschi 3 жыл бұрын

That's correct, if you go to the 4 min mark you'll see the before and after wiring diagram. If I had an aftermarket ECM/ECU and could actually use them I would.

@Hygoog 6 жыл бұрын

Can you drive with the AEM UEGO gauge without installing the o2 sensor?

@AlexFranceschi 6 жыл бұрын

Sure, you could, but you would not be able to read the AFRs.

@Hygoog 6 жыл бұрын

Oh ok. I just need it to get hooked up right now until I get my turbo downpipe installed. Would it be a lot easier if you just use circuit holder connectors instead of splicing into your harness?

@AlexFranceschi 6 жыл бұрын

Whichever method you find easier. I by no means used anything fancy. Just the fact i had some splice connectors on hand when i installed it. You should at least be able to hook everything up, even the wideband outside of the downpipe just to make sure the system is working and communicating.

@HRenteriaRenteria 5 жыл бұрын

Any idea on why mine reads eugo sensor off line?

@AlexFranceschi 5 жыл бұрын

No idea, hard to diagnose such things online, but I would refer to the user manual, double check all connections, and insure you have the software with appropriate drivers installed. Good luck!

@josecarmona4858 6 жыл бұрын

Hello, I was wondering what angle kit are you running?

@AlexFranceschi 6 жыл бұрын

Jose Carmona I'm running JTPs Hotline knuckles. I don't think he makes them anymore, but I've had these for ages. There are other companies who have some angle kits but if you don't want to buy knuckles you could go with Mazdatrix rack spacers and tie rod ends.