Aerial Fiber Optic Fusion Splice from ladder and Inside House

Рет қаралды 8,510

Ай бұрын

800ft plus Fiber Optic run with inside installation.
amzn.to/4bVWQGM 30mw red light pen fault locator
amzn.to/3SXw9c0 54" sidewalk dirt drill bit auger
amzn.to/3wocxX2 39" masonry drill bit for vault
amzn.to/49G2lHw fiber optic light tester power reader
amzn.to/42MmHMY mini pick axe
amzn.to/48ogatl strong spade shovel for drop burial
amzn.to/3wlDyu9 Orientek T49 full fiber fusion splicing kit
amzn.to/3K6YF71 Signal Fire New Model AI-6A Fusion Splicing
amzn.to/3uAbin5 trampoline hook for opening vault and grabbing fiber
amzn.to/48hOpCt 425ft fiberglass fish tape rodder
amzn.to/49qJcK9 sharp sidecuts
amzn.to/3U6e4cv TAWAA FC-20 Cleaver
amzn.to/44dV1l1 VAE-YI V1 Drop Proof Cleaver
amzn.to/3U6egbJ FC-S6 Optical Fiber Cleaver
amzn.to/3vSeATn Head Mounted 4K Camera

Пікірлер: 38

@gregoryfaith4303 Ай бұрын

In a time long ago, 1990, at the B-2 Flight Test Facility at Edwards A.F.B, CA I was taught how to handle, install, terminate and test fiber optic cables and the equipment associated with it. Our group laid the cable network throughout the facility and maintained it until I left in 1995 to move over to NASA DRYDEN after the bomber flight testing ended. It was fun.

@nerdindy1406 Ай бұрын

They do a good job, the speed is incredible 🙂

@paula1493 Ай бұрын

Good video, I like to see the inside work!

@redabahlas Ай бұрын

That is a good job- Splicing optic fibre in space .

@JasonsLabVideos Ай бұрын

Nice work !

@christopherconnolly5340 Ай бұрын

Great work.

@nick21614 Ай бұрын

Gotta use a clean wipe and not touch the fiber with your fingers 😇

@naturallyrootedgrowers Ай бұрын

I will give it a try!

@Natsumidragneelkim 16 күн бұрын

@@naturallyrootedgrowers yes that's poison oak on that tree

@michaelwroblewski6546 Ай бұрын

Whooo hoooo new video!

@travisrobinson430 28 күн бұрын

Make a coil then zip tie it to a strand then use lay up sticks to push it threw tree

@CodeWithMilijan Ай бұрын

Your work is nice mate!

@CodeWithMilijan Ай бұрын

and hello from russia

@naturallyrootedgrowers Ай бұрын

I appreciate it, thank you

@jean-michelbarreau5933 Ай бұрын

wow it seems ive lucked out here in ct. drop plugs right into mst, no cabinet to go to to supply each port. each mst has a one dome or a coyote. splice box supplies mst, run drop from mst to house. splice fiber to pigtail in NID, done. cant beat it

@Wintersky136 Ай бұрын

Ever thought about why you shouldn‘t touch the fiber after cleaning it with alcohol? Try cutting, cleaning and instantly fusion splicing without touching thr fiber… your „breakage“ problems will be gone!

@cts8427 Ай бұрын

I do the same job... but i didn't splice in the air... yet.. :)) ... nice..

@ThisManzzz Ай бұрын

Are you not concerned about the excess fibre being cleaved right onto the ground?

@bassgodzbasshousemixes8737 Ай бұрын

How do you like that splicer??? Or is it a company provided one??

@naturallyrootedgrowers Ай бұрын

As a contactor we buy everything out of pocket including gas, vehicle , commercial insurance, and liability. In my opinion this T49 doesn't do well in outside environments, unlike the signal fire A9 or any of them, A10 has a built in cleaver which has me mixed on loving it or hating it. You have to strip the fiber like 4 inches to put it in the cleaver. So A9 to A6 are all pretty much the same, except some have light readers and red light fault detectors built in. Most of the other techs i know use the signal fire and dotn have the weather trouble I do with the bubble/divits right in the middle of the splice. I cut out 4 splices on the ladder that went bad on this video.

@bassgodzbasshousemixes8737 Ай бұрын

@naturallyrootedgrowers Thanks for the info. Been binging on your videos in the mornings for a couple months. Im doing a project wiring 18 homes/cabins on 40 acres but 3 are over the 330ft to use copper. Was going to use poles to get to them but going with only conduit. So im not using flat drop cable due to that...I notice you splice into the patch cable into the nid....are you using om1?? (Obviously im a newb) keep posting btw 🤘

@naturallyrootedgrowers Ай бұрын

If you can get by with data only like wifi equipment and have line of site , I have used mikrotik 60 ghz cube($300 pair) , for a wireless bridge at a trailer park. It was 6 or 700ft apart. with 3 sets of these cubes all getting close to a 1gb through the air. You can buy these preconfigured as pairs. Or buy ethernet to fiber adapters , but they usually need 2 fibers into the adapter to work, they are cheap like ($30pair) im sure they are good for a few thousand feet. I have those at the trailer park also.

@Bill_N_ATX Ай бұрын

You guys are nice. The local fiber guy hung the fiber jack on the side of the house and said I was on my own to get the cat6 to my router. Thankfully I ran network cables back in the day and to be honest, I’d just as soon do it inside my house so I know it’s done correctly. When I got the line it was 1gb. Now they offer 8gb. How much porn do you watch that you need 8gb?

@THANIS_ALVIN_DAVID_RAJA 6 күн бұрын

Which brand optical modems your using.....?

@naturallyrootedgrowers 6 күн бұрын

ciena 3801 and adtran sdx621

@Wintersky136 Ай бұрын

43:30 and I swear it‘s your bad practices!

@naturallyrootedgrowers Ай бұрын

I have been making sure of not touching it lately and i think your on to something.

@dave56ize Ай бұрын

I agree, dont touch the fiber after cleaning with a lint free alcohol wet wipe. Wipes are cheap, use a clean one and dont touch the cleaned fiber and you will see the improvement. I liked the aerial splicing, pretty neat.

@killswitch768 Ай бұрын

i could not see but the slack of the drop lines but from the last video it makes it look like the aerial splice domes are never going to make it back to the ground? I am so glad your the one tech visit though. Watching Verizon do a , inside fiber tech, outside fiber tech, then cpe final install tech is about the most inefficient thing i can watch.

@naturallyrootedgrowers Ай бұрын

All the mainlines usually have enough slack to reach the ground, but they need taken off the snowshoes and that gets heavy to put back up and time consuming. The other problem is the main problem that most techs dont care and wont take the time to find the correct snowshoe path making it impossible even drop the line/nap since its wrapped and tangled in the wrong direction.