Since there is no rebuild guide to this, i took some time to make one. Simple and straight foward. (I am no responsible for damage to your part)
Пікірлер: 123
@mjh78 Жыл бұрын
This is hands down the best tutorial I've ever seen! Down to every little detail
@ritchardposterior2625 ай бұрын
Hey dude, massive props for this video. i don't have any issues with mine but the walkthrough you did is 100% top notch. you single handedly made these airlift 3p/3h manifolds repairable by the masses. Thanks brother!
@redspowerjams4 жыл бұрын
Thanks for taking the time to provide that very instructional video.. I liked being able to take a look into the manifold but it was even better learning some of the tips on how to fix leaking issues if they ever come up on my unit..
@josecalderon2333 жыл бұрын
Just take the rear cover off and throw it in the oven for 30 min and moisture gone. Worked good for me and I put a water trap to avoid anymore moisture from enterning the manifold
@bilalali88322 жыл бұрын
Hi mate I have a pressure sensor failure on one of my bags. Researched told me its the manifold at fault and need a new. Could your solution fix this? If so which part for I need to take off and which part goes in the oven. Thanks
@josecalderon2332 жыл бұрын
If you still have the warranty call airlift If not take off the bottom cap and and the 2 screws on the sides and put it in the oven for 30 to 45 min. I used 250 temp. Helps get the moisture out.
@Aaphree3 жыл бұрын
Thanks for taking the time to do this. I just had a failure today, pretty sure water froze in the manifold. Only the front left valve leaks, but the air comes out the back of the manifold from the center seam (where the top and bottom outer halves meet). I think the o rings got out of place or got ripped from the ice expanding in the manifold. Might try to do this before ordering a new one (or just go back to stock suspension for now lol)
@zpope93 жыл бұрын
How did it go having the same problem
@Aaphree3 жыл бұрын
@@zpope9 haven't tried it yet haha
@justinngo4967 Жыл бұрын
@@Aaphree did it work? i am having the same problem as you
@Aaphree Жыл бұрын
@@justinngo4967 Ended up going back to stock and selling my air setup. Still have the manifold though, so I will probably just open it up to investigate even though I have no intentions of reinstalling
@originalmusic4013 жыл бұрын
Nice video. I'm gonna run 3 water traps. 2 in between my 2 compressors and tank and 1 between my manifold and tank.
@MrTheHillfolk Жыл бұрын
I'm definitely adding another one. I've got the one from the kit on the tank outlet going to the manifold, and being familiar with shop air and whatnot that thing looks really small. I've got a spare one for the shop that I think I'm going to plumb in after the first one. My system is mostly hidden ,but has easy access for draining the trap I've already got. The second one can be a little more hidden, as it's only to catch water if the first one doesn't get drained often enough. And I'm still building the car so it's not too hard at this point to go back in.
@japs01tv4 жыл бұрын
great job.! salute to you this is a big help to fix and clean the manifold
@BrownEye02 Жыл бұрын
Parts List: Small Green O-Rings (ID .007", OD .21", W .007"): GRAINGER Item Number: 1KER6 Large Green O-Ring (ID .614", OD .754", W .007"): GRAINGER Item Number: 1KET9 Pressure Sensor (PN 26PCGFJ2G): Ebay from seller sgayterboi20 was the cheapest option at the time. ($23.72 as I ordered 2) P.S. - Comment keeps getting deleted if I include URLs Reply if you find sizes/parts for other things to help others!
@itzdreamer581511 ай бұрын
Cant dint the pressure sensor or valve whats the part number ?? HELP PLEASE 😫
@Li9hTsFTW10 ай бұрын
@@itzdreamer5815 search that part # and it should come up as a Honeywell pressure transducer
@sethstayfresh51637 ай бұрын
Can you send link can’t find I need the really tiny ones lost them while opening up
@sethstayfresh51637 ай бұрын
MVP if these actually fit for the small ones just ordered
@BertLourens2 жыл бұрын
man, you are awsome, works perfect! i am having my manifold apart because i want to try and make an threaded manifold instead of the cartridges
@RyanParaggio4 жыл бұрын
Good looks on putting this together, big help and much appreciated.
@stuartcturner10 ай бұрын
Very very good attention to detail, thank you
@robertvanrooyen38894 жыл бұрын
great video, thanks for taking the time to share this to your fellow diy people!
@itzdreamer58158 ай бұрын
Anyone know the plunger part number???
@parales039 ай бұрын
I bent my pins on the connector. Can those be fixed?
@hubertallicock43363 жыл бұрын
Thank you for pausing that, sounded crazy for a sec 🤣
@michaelcarver14173 жыл бұрын
Thanks for this video! What are the brass screws for on the ends of the manifold? Are they like a drain or manual pressure release?
@jasperpulakka14663 жыл бұрын
Hey bro, Do you have had any problems with pressure sensors. Im imaging that tohose black tubes on the back of the motherboard are pressure sensors, are they🤔 And do you think that cleaning them up could help with the pressure sensor fault?
@iAmSwog3 жыл бұрын
Wondering the same thing, did you try to clean them up or solved the problem? Having same issue of pressure sensor fault
@projectf0254 жыл бұрын
Damn man thanks for the video mine leaks like crazy
@xclusivekid1232 жыл бұрын
Great vid, my question is is there any electrical parts in that last piece after you took everything off?? My car was flooded back in September of ‘21 and it does work but I wanted to take it further apart and don’t want to ruin anything.. any and all info is appreciated 🙌🏼
@lrod234411 ай бұрын
Hey people if you dont have new o-rings take it from me do NOT NOT NOT drop any if them… I dropped one of the small black ones for the plungers and never found it… I wound up using a plastic one and the manifold apparently did NOT like it and when I out it back i wasnt paying attention to the controller instead focusing on leaks… there were no leaks but I didnt know that the damn manifold kept filling the bags until one exploded. I quickly unplugged it and had to cut the lines to release the pressure.
@lrod234411 ай бұрын
Where can i get a new long seal? The one under the backplate? Mine stretched when I was cleaning them. Thanks.
@josejimenez-lc3cg10 ай бұрын
tengo este problema ayuda por fabor
@oscarg314773 жыл бұрын
I have a feeling that I have the same problem. My tank leaks over 100 psi over night. But I’m not brave enough to do what you’re doing!
@pablow20092 жыл бұрын
Great video bro thanks
@chasebeck28713 жыл бұрын
My plunger won't snap together even without an o ring. Is my plunger bad?
@lrod234411 ай бұрын
Seems like the only decent video anyone has made. All these other clowns say: I “fixed” my manifold… by sending it back and getting a new one…. How is THAT a fix???
@kymyu Жыл бұрын
"Does anyone know where I can get the wiring diagram in case I don't have the cable harness?"
@dalls214hoe3 жыл бұрын
Do you know what size are those small o rings? I have a broken one and it’s leaking and can’t find one that fits
@sethstayfresh51637 ай бұрын
Did you find one yet
@resdawgs2 жыл бұрын
Wow is this the problem with all leaking manifolds including mine.?
@DivineBk2 Жыл бұрын
Ever have the issue where if I start the car the manifold won’t power up. If I leave it on, then unplug it, and plug it back in, it starts up fine? Seems like the remote within the manifold is messed up somehow.
@roboparkour Жыл бұрын
Hi mate you ever find a solution for this?
@viktorsirak18023 жыл бұрын
Hello. I really need a valve for manifold ALP 3P 3/8 ”. Can you advise me where to meet him? well thank you
@JosueLopez-st5zr4 жыл бұрын
I tried doing this to mine but i still have a leak on the “T” connection. Would you know what i did wrong? Followed these steps carefully
@chasebeck28714 жыл бұрын
Same problem
@bigmacchronicles44464 жыл бұрын
What t connection?
@snipern2163 жыл бұрын
Did you guys fix it ?
@alexperez6513 жыл бұрын
Your the man 💪🏽💪🏽💪🏽💪🏽
@alexxx3958 Жыл бұрын
Anybody got any ideas for repairing inside the manifold where the PTC push in cartridges go? It got scratched pretty bad when replacing a cartridge and now leaks badly.
@ghost_m3p8 ай бұрын
Chances are that the leak is due to you not having the fitting in all the way. The front scratches dont release air.
@ticklemypickle2704 жыл бұрын
what would cause the right rear on my manifold to stay at 42 psi constant pressure and not air out or air up? its froze up and wont do anything when i hit the button with 149 psi in the tank??
@fernandogarcia82522 жыл бұрын
I have the same problem have you fixed it yet ?
@jasperpulakka14663 жыл бұрын
Great video btw👌🏽👻
@BNHFcarsupplies2 жыл бұрын
Who does not have problems with that brand 😂
@truebreed894 жыл бұрын
What if its leaking from the fitting part I'll own up to it I did a rookie mistake and pulled the air line out while the car was aired up i have read that I might of blown an o-ring left the car aird up over night and the next day that one side is completely AIRD out while all the other sides are still up checked it for leaks and its leaking from the fitting......HELP MEEEEEE
@bigmacchronicles44464 жыл бұрын
Fitting are replaceable
@Barbocz1004 жыл бұрын
Thank you man!!!
@MrDarckangel584 жыл бұрын
Where can i get the green orings?
@keithspencer15093 жыл бұрын
Don't these have a lifetime warranty?
@Darrah24_2 жыл бұрын
@@jonathanfraire8394 not anymore
@chino0222 жыл бұрын
@@Darrah24_ they have like a 1 year warranty now right?
@Darrah24_2 жыл бұрын
@@chino022 yes. Their warranties have changed a lot. There’s certain restrictions. I’d go take a look. I switched to Accuir because of it.
@chino0222 жыл бұрын
@@Darrah24_ oh okay and I was having problems with my manifold it said on the control fault: pressure sensor and I took it today to get fixed
@Darrah24_2 жыл бұрын
@@chino022 yeah that very common to be honest. Don’t know why Airlift won’t freaking fix it.
@abrahammadrigal9027 Жыл бұрын
I’m having issues on mines but once my compressor is one it airs one bag by its own ? Any tips on what the problem could be
@strboy7189 ай бұрын
Did you ever fix the issue?
@strboy7189 ай бұрын
I wanted to know..if you air up or air down and it doesn't settle is that a leaking issue?
@chrisc292025 күн бұрын
Did you ever find out? My car has the same issue
@ASVPxLALO3 жыл бұрын
What size are the Allen Keys?
@truereligionkhan4843 Жыл бұрын
that’s what i’m tryna figure out
@XllllllllX- Жыл бұрын
@@truereligionkhan4843 súper fucking small
@GUITARboy2554 жыл бұрын
I have a problem with my pressure sensor RR i get a reading. But it is to high and sometimes it goes out of reach. As far as i can tell it isnt moisture. I noticed that while rising the pressure goes way up and after rising goes down to somewhat higher as the left side. Do you have any suggestions or can i replace the sensor? Hope you can help me thnx
@MrDarckangel584 жыл бұрын
Why everyone has problem with that sensor .. I just have that problem too....😪😪😪
@jasperpulakka14663 жыл бұрын
I got this problem too😖 I hope I will find out how to solve this problem.
@GUITARboy2553 жыл бұрын
@@jasperpulakka1466I fixed the problem, search for the honeywell 26PCGFJ2G. This is the sensor you need to replace. Hope this helps you out👍
@jasperpulakka14663 жыл бұрын
Thaks A LOT man! I will try this!
@snipern2163 жыл бұрын
@@GUITARboy255 what that bro ?
@Cjoseph07134 жыл бұрын
Would doing this help a pressure sensor fault?
@bigmacchronicles44464 жыл бұрын
Possibly if there is debris there
@iAmSwog3 жыл бұрын
What about the pressure sensor fault? Can it be solved in some way?
@thatbaggedsrt2 жыл бұрын
I too am wondering this.
@djkarloshouston2 жыл бұрын
I was having that issue a lot bacn then.. but im prety sure i found the issue, normally you get that warning when you have over pressure in the tank, the manifold gets into safe mode and sends that code... for example, i go to gym and leave my car getting direct sun and with high tempetures, my tank being in full pressure and getting heat, the pressure expands, and the manifold enters in safe mode or pressure sensor fault. i made an experiment, and left the car again with direct sun light and high temperatures outside the parking lot, but this time the solution was to leave the tank half empty, and there you have it. . no more faults.. and i did notice the pressure was higher than before when i came back from the gym to my car. . remember you have some water in the tank, and with the heat the water condensates and creats more air in the thank....im so sure airlift knows this, but i bealive the dont say nothing about ot bcuz they run a bussines and that type of stuff gets the more manifod purchases when the manifold its not under warranty no more. I hope this its helpful for anyone out there having headaches bcuz of that pressure sensor fault thing lol .. and just to let yall know i havent got that issue any more, and i did not change the maifold either. and just for the record I run the 5 gallon tank and 2 compressors.. yalls may be diferent but its the same concept.
@aarixk2620 Жыл бұрын
Need a video on how to replace the pressure sensors
@BrownEye02 Жыл бұрын
Just posted the part number and where to buy. Grab your solder gun and should be a quick swap
@windjlw9918 Жыл бұрын
@@BrownEye02 did you just swap your sensor out and it fixed? or is this a theoretical fix that hasn’t been confirmed
@BrownEye02 Жыл бұрын
@@windjlw9918 I was able to successfully fix my manifold by replacing my front left sensor. My issue was a sensor fault of course but would read 0 even after letting it sit in the house on a heater for a week. I'd highly recommend removing your manifold and letting it sit on a heater vent in the house or putting it in rice for at least a couple days to hope that your issue is simple moisture in the sensor. If that doesn't fix it though then you for sure have a bad sensor or debris in the sensor. I'd recommend following my recent post on checking the sensors with a multimeter to confirm. You can separate the needle end from the sensor body but the sensors are VERY sensitive and my bad one I ended up damaging even more when I did it. Was just curious as I think mine failed due to some Teflon tape making its way in. That or some assembly grease.
@windjlw9918 Жыл бұрын
@@BrownEye02 yea your the only one that’s really talking about this fault and a solution, i don’t have warranty and don’t see the reasoning for spending 900ish for a new manifold when it’s merely a sensor replacement. drop your email or some way i can contact you bro. id appreciate the help
@BrownEye02 Жыл бұрын
@@windjlw9918 Sadly when I just checked I was being told like 1200$ for just a manifold...... Shoot me a PM and I can't drop you an email or something and help where I can. Was in the same shoes you are in not a couple weeks ago but hopefully you can join the "fixed it" club.
@jaspalewis2221 Жыл бұрын
Does anyone know a part number for the 2 peice plastic/metal valve?
@ollyp56 Жыл бұрын
Have you found out yet? I’m looking for them can’t find them
@MrTheHillfolk Жыл бұрын
If those parts are proprietary to air lift ,you won't find a substitute unless it's aftermarket, and even then it might be patented or whatever, and that means the aftermarket can't even reproduce them for 10 or 20yrs(when the patent runs out). O rings and stuff like that are easier to match up. If air lift is having them made by someone ,you might be able to find out but doing all that is a lot of research. Makes me wonder how much stuff they get "off the shelf" and if so from who, or do they produce those valves in house.
@jaspalewis2221 Жыл бұрын
Yeah ive been searching for months and nothing... my guess is they are made in house... 😔
@itzdreamer581511 ай бұрын
Anyone know the part number or where i can get the valve or plunger
@strboy7189 ай бұрын
Did you find the plunger anywhere?
@itzdreamer58159 ай бұрын
@@strboy718no I couldn’t find it
@johnnyg92484 жыл бұрын
You ever found a part number or a size for the green o-rings?
@bigmacchronicles44464 жыл бұрын
I have a measuring device for o rings on the way to give exact measurements
@johnnyg92484 жыл бұрын
bigmac chronicles that’s awesome! I just bought a huge kit this morning from amazon. Only tough ring was the one large black one, that I wasn’t able to find online.
@sebastiancolon14243 жыл бұрын
@@bigmacchronicles4446 Any update?
@rocketkn Жыл бұрын
@@johnnyg9248 Hello, can you give me link for o ring green please ??? thank you very much
@juanmartinez-ry9uv4 жыл бұрын
Hey bro like your vid. Great info... do you have an IG .. would like to see your Chevy
@bigmacchronicles44464 жыл бұрын
Yes sir! @the_real_bigmak
@youtubedev0 Жыл бұрын
Air Lift manifolds are failing left and right. A lot of people are going back to brass valves for cost and lifespan. Manifolds are garbage.
@FabioSilva-ek5yk4 жыл бұрын
Make one for v2
@bigmacchronicles44464 жыл бұрын
Unfortunately i dont have one at hand bro
@FabioSilva-ek5yk4 жыл бұрын
bigmac chronicles do you know how to do it though or where to find parts?
@bigmacchronicles44464 жыл бұрын
@@FabioSilva-ek5yk shouldn't be too hard
@Clemotion4 жыл бұрын
V2 really need to a video like this haha thanks for this rebuild :) you know where we can find part ? thanks from France :)