2007 Ford Focus 1.6 ..Removing The Tight Crankshaft Bolt & Cambelt Replacement Overview

  Рет қаралды 42,566

Alan Howatt

Alan Howatt

Жыл бұрын

Using a heat gun to remove the tight crankshaft pulley bolt in order to carry out a cam belt replacement, also how to bleed air from the cooling system.
• 2012 Ford Fiesta 1 25 ...

Пікірлер: 135
@bernardmackle6900
@bernardmackle6900 19 күн бұрын
Was completely stuck as the bolt wouldn’t move, so watched your video, tried it with a Mapp blow lamp and worked an absolute treat!! Thanks very much! You’ve saved my sanity!! 😂😂
@alan4x
@alan4x 15 күн бұрын
excellant 😁
@allsystemsdownagain9553
@allsystemsdownagain9553 3 ай бұрын
Love this guys honesty when doing videos. No pissing about. Straight to the point.
@paulriggers1558
@paulriggers1558 Жыл бұрын
10 yrs ago, i couldn't get a focus bolt out, snapped 2 sockets + my extension bar, phoned the lads at ford workshop, "just smash all the bottom plastic cover off, + slip the belt over the pulley", "once the top cover is back on, the customer will never know" "never had one back yet to complain" main dealers, gotta luv 'em....
@parkpondcarp
@parkpondcarp 7 ай бұрын
Bet wthat will get contaminated real wuick with oil and debris your smart proper bodge job
@arbengagam2545
@arbengagam2545 Жыл бұрын
Back to business mr Allan . I’m learning another 1 each time you post this informative mechanical video of yours because I’m trying to do my personal maintenance on my ford s max 2007 taci .. great video thanks a lot
@vincentshoona4676
@vincentshoona4676 Жыл бұрын
Another brilliant video Allen well done. You and Rain Man repairs are my favourite well done. Keep up the good work. Absolutely love it❤
@mrxr2
@mrxr2 11 ай бұрын
Just finished doing a cam belt on my Ford Fiesta Zetec S mk5 (2002), struggled yesterday with the crank bolt, nothing would touch it, had the air compressor out set to max, nothing. Almost at the point of giving up, but found your video last night. 8am this morning dragged the comp back out and dad's 1993 black and decker heat gun, few mins of heat and the bolt came straight out with the airgun. Thank you so much for the video, this really helped me out. Also did the trick holding the coolant tank in the air, worked brilliantly. Have subbed :) My timing kit has a locking pin, you replace the timing pin and use it when tightening the new crank bolt so no need for the flywheel locking tool.
@alan4x
@alan4x 11 ай бұрын
lmao🤣its easy when you know how, thanks for the comment, made me laugh, have a good one
@ErgensUit1987
@ErgensUit1987 2 ай бұрын
Many thanks. And as far as i have seen the majority videos of changing belts on these 1.6 zetec engines. you are the only one who releases the camshaft sprockets. hats off to you sir!
@alankeane4059
@alankeane4059 Жыл бұрын
Good to have you back on car videos Alan
@paulwharton1484
@paulwharton1484 3 ай бұрын
Thanks so much for this video, I was ready to pay a garage until I found this great video, it worked a treat.👍
@miketherefurbisher8000
@miketherefurbisher8000 Жыл бұрын
An incredibly useful video Alan!! welcome home from your Holiday, you left us with a bit of a void. "Fantastic"
@zzhughesd
@zzhughesd Жыл бұрын
Just watched EuroV. This was a nice tonic Alan. Thanks.
@zoidberg444
@zoidberg444 Жыл бұрын
The cooling bottle is a clever trick. I'll remember it next time I do one of these... Thanks!
@Roadkill7878
@Roadkill7878 Жыл бұрын
Great hack Alan raising the reservoir bottle up.
@garymorris4147
@garymorris4147 3 ай бұрын
I can't believe it worked 😂 thank you so much. The last time I did one of these I made a tool to hold the pulley, although the bolt came undone the pulley shattered as well. Thanks again.
@alan4x
@alan4x 3 ай бұрын
Fantastic, glad it worked😊
@JonWhitton
@JonWhitton Жыл бұрын
Welcome back to Blighty Alan!
@CTX-wh5qu
@CTX-wh5qu Жыл бұрын
Quite a few "top tips" there Alan. Awesome informative vid as always. Cheers Alan.
@frundlemud
@frundlemud 9 ай бұрын
Another good solid job. The hot air gun usage probably expands the stretch pin. I will remember this idea. Your timing and rechecking, points to a experienced mechanic.
@Shandybrother
@Shandybrother Жыл бұрын
Going to miss all this good stuff if and when you go 😢
@kellytaylor3134
@kellytaylor3134 Жыл бұрын
Where's he going
@LBytCH1
@LBytCH1 Жыл бұрын
Great tips Alan - many thanks!
@milandjukic3589
@milandjukic3589 Жыл бұрын
Alan nice one,,))) you smashed it again 😊🇬🇧👊
@graememcdonald6882
@graememcdonald6882 Жыл бұрын
Excellent video, some really good points 👍
@patkelly7999
@patkelly7999 11 ай бұрын
Mighty job Alan, very well explained, Thank You💯👌👍🙏😎
@johnchincotta1qwdb15
@johnchincotta1qwdb15 Жыл бұрын
Hi Alan,a very nice and informative video. Back to the spanners once againg.
@geraldharkness8830
@geraldharkness8830 Жыл бұрын
great video as usual alan!
@bartoszk4812
@bartoszk4812 Жыл бұрын
Nice having you back Alan although it must have been hard going back to work 😭 I tried my Dewalt impact gun on this bolt and it wouldn't twitch. Nice Pro Tip with a heat gun 👍 USPro tools are good but I think we need more powerful guns.. $$ Auch I figured out that tip with a bottle too 😁 does the trick with bleeding the air out the system 👍
@stephenegginton7590
@stephenegginton7590 Жыл бұрын
Great vid Alan that timing belt replacement is very similar to the 1.6 Renault magane which I’ve done a few of 👍👊
@mechtechmechanical1571
@mechtechmechanical1571 Жыл бұрын
to lock the crankshaft pulley bolt I use a set of stillsons through the pulley to hold it and a small piece of wood on the jaws so it doesn't damage the pulley saves loads of time an you can hold the flywheel pulley great vid
@user-sf7kl9uh7k
@user-sf7kl9uh7k Жыл бұрын
Oh good, your back!
@kevinthacker8349
@kevinthacker8349 Жыл бұрын
Perfect timing, job I’ve got to do on son car this week
@ianwilkinson5549
@ianwilkinson5549 Жыл бұрын
Great video mate .
@chrisbell-pctechnician3784
@chrisbell-pctechnician3784 Жыл бұрын
Top info as always
@halleffect2000
@halleffect2000 4 ай бұрын
thanks for the video I am doing the timing belt on the 2013 ford fiesta timing belt, people talk about using the torque wrench for the crank bolt, I am just using the impact gun by full power, that mostly I do when I working on the timing belt.
@robturner7945
@robturner7945 Жыл бұрын
Top tip that with the coolant bottle. I like it a lot.
@laterego1
@laterego1 Жыл бұрын
Welcome home fela!!!!!
@sandyande
@sandyande Жыл бұрын
Great video great tips cheers Alan, Sandy
@MattyEngland
@MattyEngland Жыл бұрын
I was worried delayed Balut poisoning had taken you. Glad to see you're still alive 🙂👍
@khennahsfarm2610
@khennahsfarm2610 Жыл бұрын
😂😂😂😂
@MrPhil6697
@MrPhil6697 Жыл бұрын
You opened the expansion bottle cap to let the graverty in?? Thought it was there already and needed air to be let in 😆 😂 😆 😂
@scotthawkins1011
@scotthawkins1011 Жыл бұрын
Great video!👍
@randysoft4266
@randysoft4266 Ай бұрын
It works, thanks 👍
@usuallyfixingtinkering
@usuallyfixingtinkering Жыл бұрын
Great Video on doing this Alan and the pitfalls that come with it. I've carried out this procedure on my MK1 1.6 and getting the crankshaft bolt out is the "squeaky-bum-time" moment - fortunately I have a Milwaukee M18 cheat gun! This takes the bolt out without heat at all. Your method works well with lowered powered guns, that US Pro Gun has half the torque that a Snap-on/Milwaukee will produce. Changing the Cambelt on these Sigma & Zetec lumps is otherwise fairly straight forward, people complain about the lack of a key-way in the crank but the timing tools make the job just as easy! P.S. I've re-used the camshaft sprocket bolts with no issues, as long as they yield when torquing to 60NM it's all good :)
@twig3288
@twig3288 Жыл бұрын
If there’s no woodruff key isn’t the sprocket likely to slip? 😱
@usuallyfixingtinkering
@usuallyfixingtinkering Жыл бұрын
@@twig3288 not with a powerful gun no
@victorharris3460
@victorharris3460 5 ай бұрын
Very good job
@daveharrison3635
@daveharrison3635 Жыл бұрын
Hi Alan ,I really enjoyed our chat last week ,well that was a great video as usual,don't forget to txt me about that show if that's OK with you and Kevin hope to here from you ,keep the video's coming they are great
@foxa3658
@foxa3658 Жыл бұрын
Proper quality air gun with high flow connections and adequate air pressure will always do the job without the need of any heat etc
@alancobbin
@alancobbin Жыл бұрын
Perfection,only thing you forgot to mention is the bottom cover gets slightly warped from the heat gun but doesn’t damage it,I’ve done hundreds over the years I can do them in my sleep lol ,nice one Fella,good to see you back home 👍😉💪
@usuallyfixingtinkering
@usuallyfixingtinkering Жыл бұрын
you always remove the bottom cover to stop this happening :)
@gtidan8467
@gtidan8467 Жыл бұрын
You haven't done one of these then. You can't remove bottom cover with pulley on!
@usuallyfixingtinkering
@usuallyfixingtinkering Жыл бұрын
@@gtidan8467my mistake i was thinking of a completely different car referring to the lower cover. But heat should not cause damage to the plastic unless you go ape with a heat gun.
@alancobbin
@alancobbin Жыл бұрын
@@gtidan8467 exactly 👍
@AlanCooney
@AlanCooney Жыл бұрын
Top video Alan! Better than Haynes Manual! I've done a 2010 Fiesta Mk7 by locking flywheel, then socket on breaker bar! However, my son took 2013 Fiesta to local garage for same job and they used the Snowpake "short cut" method - worked fine and must have been much quicker to do!
@thehutx
@thehutx Жыл бұрын
whst is snowpake
@AlanCooney
@AlanCooney Жыл бұрын
@@thehutx Snowpake is a small bottle of white quick dry paint (including mini brush) that office typists used to “paint over” typing errors on paper.
@MikeSmith-tg1ku
@MikeSmith-tg1ku Жыл бұрын
A Torque Multiplier has always worked for me
@DjT0105
@DjT0105 Жыл бұрын
Hello Alan 😊 Nothing personal,but.. Its good practic to replace cams seals and crank seal on same time🥳 I like your all the videos 🤙👊🏼
@zoidberg444
@zoidberg444 Жыл бұрын
On the other hand if they're not leaking do you really want to disturb them?
@DjT0105
@DjT0105 Жыл бұрын
@@zoidberg444 Yes I do
@mthocr1717
@mthocr1717 Жыл бұрын
Good tip but you can hear the gun is starved of air, use high flow fittings and 1/2 hose and you will get a big power boost
@plumbc007
@plumbc007 Жыл бұрын
Top Tip Alan ,,, do not put the cam lock tool in place before you have cracked the crank bolt loose ,,, there is a chance of snapping the cam lobes with the tool as you yeet on the crank bolt. hope u had a good holiday bud
@rafdannyboy
@rafdannyboy 3 ай бұрын
I wish i would have seen this comment an hour ago...... I now have to replace the intake cam... FML
@yvzzyrk
@yvzzyrk 11 ай бұрын
Büyüksün ustam ❤
@bestysbits2071
@bestysbits2071 Жыл бұрын
Good video thanks 😊
@alan4x
@alan4x Жыл бұрын
You’re welcome 😊
@ianwoollard9008
@ianwoollard9008 Жыл бұрын
Great to see you're back Alan. 👍👌👏👏😉😉 I'd hate to strip the thread with the windy gun wouldn't you? Those 3 cyl Fiesta engines require a torque multiplyer don't they? What a daft idea. 😂😅🤣
@CORRIGEEN71
@CORRIGEEN71 Жыл бұрын
Great to see you back in your natural habitat even if you don’t agree at least no flies! I use gas torch to heat simple plumbers heat gun better I think? Renting an o7 car too old?
@Longtrailside
@Longtrailside Жыл бұрын
Get a lisele weighted socket, works wonders on pain in the butt bolts. Honda had this issue in the late 90's and the lisele socket fixed that issue mechanics had with them and not destroy the crank seal with heat.
@user-sf7kl9uh7k
@user-sf7kl9uh7k Жыл бұрын
Can the heat toast the pulley seal?
@riyadhboucenna1443
@riyadhboucenna1443 Жыл бұрын
Great video as usual just a question, don't you risk damaging the lip seal ?
@987azza
@987azza Жыл бұрын
Been watching a lot of your videos I like your no nonsense approach and straightforward information. I have a mk5 mondeo and the rear passenger side caliper has failed (rear discs and pads were done 2 months ago) is it possible to just change the disc and pad on the passenger side? As the driver side is only 2 months old, I hear about brake balancing ect, but SURELY there would not be any difference if it was left on and only changed passenger with new caliper?
@michaeljohnson1006
@michaeljohnson1006 Жыл бұрын
I've never used one but I have seen those big sockets with the big weight. Are they any good? Or you could weld a big round piece of metal with a hole in on a impact socket
@antonymaddocks1918
@antonymaddocks1918 10 ай бұрын
Thank you for your video on changing the timing belt and water pump. Does the same apply for a ford fiesta zetec mk5 05 plate please ?
@kenfiorentini28
@kenfiorentini28 Жыл бұрын
ask snap on for weighted sockets i use them on hondas which are usually mega tight .... there's a couple of vids on here somewhere that show them
@Non-Stick_Pan
@Non-Stick_Pan Жыл бұрын
I was shouting 'heat' from the start of the video Alan, but I used a yellow can Mapp gas torch on mine hahahah
@-DC-
@-DC- Жыл бұрын
When would you recommend changing the timing belt on a 1.5 Tdci al ?
@jamescooper169
@jamescooper169 8 ай бұрын
Hi just wondering what would be the best way to remove crank pulley bolt without any power tools, just a breaker. I have a manual so my thoughts were to put it in high gear and press the breaks down.
@ericglass952
@ericglass952 Жыл бұрын
Good vidoe as always . How is work know you are home.
@bigron26048
@bigron26048 Ай бұрын
I have a 2015 Ford Fiesta with over 250,000 miles on it. It still has the original timing belt on it😮
@andrewball8714
@andrewball8714 Жыл бұрын
Great video. What is so difficult about removing the starter and putting a proper crankshaft locking tool in place? That's what I did, adds about an extra 30 mins. Then you know you can properly angle tighten the crank bolt and if it is difficult to remove, just use a long breaker bar with 3/4" drive socket and extension. Now my concerns would be that the heat would degrade the rubber in the harmonic balancer and damage the crank oil seal (not a problem if you are replacing these). Also how do you know what torque you have done the bolt up to with just a blip of the impact gun? You could of at least done the initial torque, marked the bolt head and then blipped it round the 90 degrees using the gun otherwise you are just guessing. Leaving the cam locking plate in while doing up the crank bolt is risky as the timing belt spocket gets dragged round as you tighten the crank bolt and puts stress on the belt and cam tool the way you done it. You should have left the cam pulleys freewheeling while doing up the crank bolt, then set timing again, then finally tighten the cam bolts. That way you don't put stress on anything. But yeah I'm sure you've done plenty your way and it works for you. Thanks for the video.
@marinusapeldoorn6631
@marinusapeldoorn6631 Жыл бұрын
Have you ever tried one of them induction heaters on the crank bolt?
@Finglesham
@Finglesham Жыл бұрын
Would that coolant refilling trick work with a Mondeo 2L Duratec?
@kevinthacker8349
@kevinthacker8349 Жыл бұрын
Can you do a how to. On changing the stretch belts please
@damoblake6000
@damoblake6000 Жыл бұрын
what model heat gun was that Alan mate top tips as always!
@1FaSS01
@1FaSS01 4 ай бұрын
Just buy a weighted socket, lifesaver!
@tiggercat8689
@tiggercat8689 Жыл бұрын
Alan, ever had a crank bolt break? Imagine that's a whole world of pain!
@user-sz2og2pk7b
@user-sz2og2pk7b Жыл бұрын
Did a mk1 1.6 recently and it was the same crap, tight AF.
@dwayne8667
@dwayne8667 Жыл бұрын
Get the milwaukee m18 high torque, it eats these bolts no problem.
@mattyb7736
@mattyb7736 Жыл бұрын
I agree, my milwaukee eats most air guns for breakfast
@OneUnited1999
@OneUnited1999 2 ай бұрын
Totally agree… had mine for 8/9 years - it’s the car mechanics’ equivalent of fishing with dynamite - too easy!
@DaleSteel
@DaleSteel 8 ай бұрын
Pumps are common to blow and they take timing belt with them. Should do a video of how you time it back up with new built. They are non.interference engines
@widelcd
@widelcd 11 ай бұрын
Thanks for the tips. I think we can all agree that Ford has again failed with the design, there are way too many difficult solutions where other brands have been smarter. Always when a Ford comes in, we have to reserve much more time for the work compared to many other.
@user-iu4jr4qf6t
@user-iu4jr4qf6t 4 ай бұрын
i thought crankshaft bolt is that 4 nm and 90 degrees, -or was it so -is it ok then just run it with impact gun so how can b shure it went ok anddd that stretch like should
@robertbowes1001
@robertbowes1001 Жыл бұрын
Sounds like you need a Milwaukee battery buzz gun mines 7 years old had no problems with it and not found a bolt it won’t undo.
@mrfishbulb7187
@mrfishbulb7187 Жыл бұрын
Agreed. 😊
@johnp6636
@johnp6636 Жыл бұрын
100% agree I have one and never had a problem with any crank bolts or hub nuts
@sirchambers691
@sirchambers691 Жыл бұрын
Yep there's nothing like a milwaukee
@leesmith2653
@leesmith2653 10 ай бұрын
Is there not a proper tool you can use that fits inside the slots on the crankshaft pulley when you are tightening it?
@RouletteNation
@RouletteNation Жыл бұрын
Where is your garage. I need the wet belt doing on my van if you are interested. Its a 2012 limited connect. Thank you
@cerulyse
@cerulyse Жыл бұрын
Will the air-gun will probably torq it😮 back up I went to Haynes manual it talks about talking at then angle tightening flywheel boots to stretch them but I don't think anyone does?
@usuallyfixingtinkering
@usuallyfixingtinkering Жыл бұрын
unless you want to lock the flywheel, there's no choice really
@iosifmocanu7852
@iosifmocanu7852 9 ай бұрын
hello mate, where are your garage based?
@martinjackson565
@martinjackson565 Жыл бұрын
Take the crankshaft sensor out and then give it some with a bolt in the sensor hole with a 3 quarter bar to do crankshaft pulley up
@stephenvanwijk1118
@stephenvanwijk1118 8 ай бұрын
You know there is a special tool you need to fix on the driveshaft bolts with build in torque converter especialy for the wetbelt driven ford engines?
@lszek2186
@lszek2186 Жыл бұрын
Hi Alan, I am about to buy a 4 post lift because I open a garage and this will be the only lift. I do not like the 2 posts because I heard some horror stories about vehicle coming off from it accidently. Is there any job I would be struggling to get done compared to 2 post lifts you can think of?
@pyromaniac354
@pyromaniac354 Жыл бұрын
2 post are much better as there is more room to work around the car. Buy a decent quality 2 post but main thing is the concrete you are bolting it down to is thick and enough.
@Magan-lg4bc
@Magan-lg4bc 4 ай бұрын
Isn t there no Fixpoint on the Pully or Crankshaft ?
@alan4x
@alan4x 4 ай бұрын
no, the crank pulley is free spinning on the crankshaft until the crank bolt holds it tight in place
@priteshchampaneri5101
@priteshchampaneri5101 Жыл бұрын
Original cambelt? Wow, surprised it hasn’t snapped by now
@davyarthurs
@davyarthurs Жыл бұрын
Known a few go ‘almost’ to second time around. I say almost, because they didn’t quite make it 😂. People are stupid sometimes
@gotj
@gotj 11 ай бұрын
Alan, those two smaller tubes that go into the coolant bottle are the bleeder lines, one comes from the top of the thermostat, the other comes from the top of the radiator, the idea is that these lines will let any pocket of air to escape (automatic-ally) into the bottle. There should always be a tiny little bit of water flowing through those tubes (on the one coming from the radiator, only when the thermostat is open). There's inside each a small plastic piece to reduce their inside diameter even further to limit the flow to a minimum. One common issue (I've seen often here is Spain) is the the reducer gets clogged because people have added water instead of coolant and things start to corrode and the coolant turns brown (with rust) and ends up clogging the orifice and then auto-bleeding won't/can't happen any more.
@Simon-ui6db
@Simon-ui6db Жыл бұрын
The ones on the citroen xsara picasso 2.0 petrol are a pig too.
@ecmmechaicsuk9535
@ecmmechaicsuk9535 11 ай бұрын
Sweeeeet
@davyarthurs
@davyarthurs Жыл бұрын
Welcome back to sunny England 😂
@DaleSteel
@DaleSteel 8 ай бұрын
Those belts won't see 125k. Water pump will go by then and snap it
@Aussiblue
@Aussiblue Жыл бұрын
Use a power bar crankshaft bolt tool made for the job, quicker and easier. Google it or do a KZfaq search.
@mrfishbulb7187
@mrfishbulb7187 Жыл бұрын
They're handy for inaccessible bolts where you can't get a gun on, but a decent impact gun would of took that bolt out.
@adrianfoy6790
@adrianfoy6790 Жыл бұрын
Alan I bet your sad to be back ?
@khennahsfarm2610
@khennahsfarm2610 Жыл бұрын
He cried ! 😅😅😅
@MegaPaulmusic
@MegaPaulmusic 6 күн бұрын
buy a decent gun (milwaukee M18) for 2 reasons 1 to save time and 2 to prevent the risk of damaging the seal or plastics also you should never use the gun to tighten anything while any of the timing tools are in place
@mrfishbulb7187
@mrfishbulb7187 Жыл бұрын
US Pro windy gun has not got enough beans in it. Try something better Alan.
@martinjackson565
@martinjackson565 Жыл бұрын
That bottom pulley bolts not tight 1.0 ecoboost is tight
@simonedwards5401
@simonedwards5401 Жыл бұрын
agree bit of heat and a scaffolding bar no problem lol
@ssss-df5qz
@ssss-df5qz 25 күн бұрын
That impact is weak.
@ZugFanTP
@ZugFanTP Жыл бұрын
Lift the Engine on the Oil Pan. Outch... Thats not a good Move.
@biinters3393
@biinters3393 Жыл бұрын
Nothing wrong with doing that providing common sense is used.
@deanreynolds1445
@deanreynolds1445 10 ай бұрын
What a crock, get a better gun, never had a problem worked for ford been doing these for years never used any heat!!!
Stretchy Auxiliary Belt Replacement, Ford Focus Mk2 1.6 Zetec
11:23
She ruined my dominos! 😭 Cool train tool helps me #gadget
00:40
Go Gizmo!
Рет қаралды 64 МЛН
THEY made a RAINBOW M&M 🤩😳 LeoNata family #shorts
00:49
LeoNata Family
Рет қаралды 8 МЛН
Osman Kalyoncu Sonu Üzücü Saddest Videos Dream Engine 170 #shorts
00:27
Puesta a tiempo Ford 1.6L 16V
15:33
Avila Mk2
Рет қаралды 212 М.
Fiesta Figo banda de tiempo o distribución 1.6
20:46
Sergio Hernandez
Рет қаралды 758 М.
Full set / Juego completo FORD FOCUS 1.6 16V FYDB .
21:29
Ajusa
Рет қаралды 213 М.
How to replace timing belt, water pump & crankshaft pulley.Ford Ecoboost Engine
15:11
Ford focus 1.6 TDCI Cambelt and Water Pump Replacement
19:36
Mr Auto Fixer
Рет қаралды 1,1 М.
# how to replace engine timing belt ford focus 2007(quick review)
9:13
Louie Lopez Vlog
Рет қаралды 10 М.
Let's go race 💞🫶😍
0:21
Sushil Barfe
Рет қаралды 1,5 МЛН
Тюнинг детейлинг МТЗ турбо
0:28
traktorist_161_
Рет қаралды 1,5 МЛН