Я прочитал много комментариев и вижу, что задаются одни и те же вопросы. Итак, я попробую объяснить, что есть в сборке и почему. Это спиртовая печь. Как заявляли другие, можно использовать и другие виды топлива. Во время сборки примерно на 3:14 вы увидите, как он просверлит 3 маленьких отверстия. Эти отверстия, которые он сверлит, являются форсунками пламени. Похоже, он сверлит эти отверстия сверлом диаметром 1 мм. Что, если вы посмотрите позже, примерно в 9:20, первое горение нехорошее, струи слишком маленькие. Затем где-то в 10:20 кажется, что он увеличил размер жиклеров до 3 мм. Посмотрите внимательно на пламя, оно действительно кажется больше. Теперь многие спрашивают, зачем использовать веревку? Веревка используется как фитиль, чтобы втягивать топливо в трубу и предварительно нагревать его. Этот предварительный нагрев топлива в фитиле запускает испарение жидкого топлива. Испарение жидкости происходит при нагревании жидкости до температуры кипения. Это также повышает температуру жидкого топлива в баке. Это повышает давление в баке, вызывая испарение большего количества топлива. Повышение давления вызывает струйный эффект. Вы хотите сжигать только пар, а не жидкое топливо. Надеюсь, это поможет кому-нибудь понять эту замечательную маленькую печь. Я надеюсь, что это хорошо переводится.

muito bom...alias exelente ... obrigado 🇧🇷🇧🇷🇧🇷

Japanese are excellent at taking an idea and making it great ...Wow well done I've never seen anything like this ...Amazing!!!

Muito bom! Vou fazer e ver se dá certo e depois farei em escala maior.

Have you tried using a silica wick in those? Im guessing regular wicks will get charred after some use. Silica wicks dont burn... They dont wick as good as cotton (at least for ecig juice), but its still pretty absorbant, and im guessing it would wick good enough for transporting alcohol pretty efficiently...

Exelente una gran creatividad felicitaciones muy bien

Hi, it works with oil diesel or gas too? Olá, ele funciona com óleo diesel ou gasolina também?

The fact that you got this to behave like a kerosene pump stove off just alcohol is impressive, very good design friend keep tweeking it to perfection

面白い！コッパーの代わりにアルミパイプを使ってもいいですかね？

Great idea👍

Excelente Gracias

Great concept.... I love it.

How long can you use the burner in one application for given cc of Alcohol?

超かっこいいですね！！ 欲しいです…

Muito criativo aliás altamente engenharia alto padrão

Saludos desd mi colombia , felicitaciones sera q c pued hacer con los tarros mas grandes , lo otro y en otra clac d material ejem: en cobre , acero y en lugar d s cemento en sus respectiva soldadura y gracias x la atencion prestada y q mi DIOS los bendiga.

Good 'ol JB weld. I've used it on several alcohol stoves on fittings. Works great!

so gonna have to try making one of these. THANKS VERY MUCH for showing me how. Great work n keep it up

Terima kasih dari Indonesia !

This material inside the coils do not get burned inside? It must pass al the way through in a single piece?

ダディハートさん 何時も興味を持って拝見させて頂いてます。 動画を拝見していて、アルコールストーブを作って見たくなりました。 色々作られてますが、（Jet stove Coil Alcohol Stoveアルコールストーブ超強力HD型） や同じ同管を使ったWコイル型・同管をアーチ状に3ケ配置して缶に穴を開けるタイプ等 ありますが、強力なタイプはどれに成りますか？ 後もう一点、火力調整が出来ないと思いますが複数個作成して入れ替えるしかないですよね？　あの接着剤は私もバイクの整備などで使用しています。 熱には強いんですね！？ 最近、年甲斐もなくディオにJF06エンジンのリーディオ作りました。 KOSO30キャブと排気ポート加工＋リア12インチでかなりスピード伸びます。

You can't go wrong when you use JB weld and they have different types of adhesive some may be more or less resistant to heat it depends on what type of epoxy you need to do the job 👍👍👍👍👍

Congratulations man

Very cool. What is the purpose of the little holes beside the main filler hole? Improves adhesion of the JB to the nut?

This is so cool. I have so many questions, though. wish the captions were in English.

Excelente trabajó

A mi me parece muy interesantes estos inventos ❤

This is cool, very clever! BTW I love how the cat stops by periodically to check on the project.

Hd hd3 does that copper tubing has little tiny holes for the alcohol to jet spray? There will be no fire whatsover if theres no flamable outlet would it?

Awesome!

Mnogo ti hvala! Dobra idea! Thank you! Good idea!

excellent video ...thanks

Отличная работа.

does the copper tubing have tiny holes under the arch ?

This is a pretty efficeint stove about 5 minutes boil...not bad.

You have a creative brain

High, a very interesting construction with the tubes. Kindly Fiete

My guess is there are NO holes in the tubing... The way ANY alcohol stove works is that the alcohol heats up (creating an increase in vapors), which then pressurizes the stove, forcing the vapors out the jets which are then burned by the flames... In most stoves, there is no direct heat being applied to the alcohol but there's enough radiant heat there to still cause expansion... In the case of THIS stove, the wick (inside the tubes) draws fuel up into the tubes, which is then SUPER-heated by the flames, hyper-expands the vapors and forces them back into the stove, which, in turn forces the vapors out of the jets at a greatly increased rate, giving it that "jet" sound.... A couple of problems I see with this design is (1) The increased pressure / heat generated by this design is going to exceed the JB Weld (glue) specs and probably fail very quickly... (2) The jet holes seem to be too small for the amount of pressure being forced through them which is right on the verge of blowing out the flames... I would either make the holes twice as big OR put 2 holes under each tube... Overall it's a good design (in theory), but that glue is going to fail and possibly be a dangerous situation... JB Weld is fine for use in stoves where there's no direct heat being applied to glued areas but this stove is purposely heating the copper which is only being held in place by glue... Be careful with that

The cooper tube is drilled?

Nice share video ..awsm 📱👍

こんにちは 各種パーツの熱の影響はどうですか？ パイプ内の麻と接着剤は2液タイプをしようとのことですが これだけ圧がかかり高温になると破損が怖そうです。

thank you

Ya entendí el funcionamiento, al calentarse los tubos de cobre con las mechas húmedas de alcohol se gasifica y aumenta la presión y sale expulsado por las tres perforaciones minúsculas de 0,6 mm. Excelente vídeo, felicitaciones y saludos cordiales desde Quito Ecuador.

I like it great idea for tiny hole for most power full fire just like a gas stove burn

Great video, and you can stand your pot on the coils too. One question: what is the purpose of the wick? Will the heat burn the wick? Will the stove heat and boil the fuel without the wick?

Good job. 4 tubes would be perfect for me.

you are so smaaaaart 😉😊

Muy bueno

I have read through many of the comments and see the same questions asked. So, I will try and explain what is in the build and why. This is an alcohol stove. They are using alcohol. As others have stated, other types of fuel can be used. During the build at about 3:14 you will see him drill 3 small holes. These holes he is drilling are the jets for the flame. Looks like he is drilling these holes with a 1mm bit. Which if you watch later, at about 9:20 the first burn is not good, jets are to small. Then at about 10:20 it looks like he has increased the size of the jets to 3mm. Look closely at the flame it does look bigger. Now, many have asked why use the rope? The rope is used as a wick, to pull fuel up into the pipe and pre-heat it. This pre-heating of the fuel in the wick starts a vaporization of the liquid fuel. Vaporization of a liquid occurs when a liquid is heated to its boiling point. This also raises the temperature of the liquid fuel in the tank. Which raises the pressure in the tank, causing more fuel to vaporize. The rise in pressure causes the jet effect. You want to burn only the vapor not the liquid fuel. Hope this helps someone out there understand this great little stove.

PARABÉNS BRASIL RIO DE JANEIRO

عاشت يدك يا بطل

Excelente pa el Café y la Maruchan o ramen

Really really nice!! Congrats my brother! I really want to make something like this now! Haha But I have to ask, how we "turn off" it? I need to wait it burn the whole alcohol inside it? If i just "kill the flame" doesn't will still letting the gas goes out of it? If there were some way to close the thin hole that let the gas out can it work to "turn off" the stove? Anyway, congrats for the nice project you have done!

Wow! How many time on the fire?

good. thanks for your video. It's very helpful

Dizel ile çalışır mı? Nasıl söndürebiliyoruz?

Witch size of drill bit you use for the jet ?

你好，你好嗎？我是從哥倫比亞麥德林給你寫信，是提前問一下你的爐子上用的是什麼膠水，非常感謝

Ficou..Muito bom..Mas está música ficou ruim de mais..kkkkkkkkk

Wow! Very good

beware, glue copper coil will eventually explode. just had my explode on me, lucky no one was burned. Creator like such video need to at least warn viewer.

Thanks a lot

Great!

オートウエルドはどこに売っていますか？

Excellent!

The holes drilled in the bottom of the tubing?

Muito bom, parabéns

Bagus banget bro..? ide kreatifx..👍 ini buat contoh untuk kita semua..supaya kita terdorong untuk menciptakan sesuatu yang bermanfaat..amin.

Super idea

Good job... Please When you insert the small pease in the top large one... are you shuted it by soldering or by devicon or just close it titly... Warm regards

すごい

How the flame out of the pipe?

hola, muy bonito y practico

Cuánto tiempo dura encendido?

ダディーハートさんは色々な銅管コイル型ストーブを制作してお見えですが、どの型が一番火力が強いでしょうか？宜しければお教えください。

Sounds just like a torch

Thanks

Wish this had english translation or english version of this. Curious how it works exactly

For How long does It burn ??? 🤔....

Vc fez algum furos nos tubos de cobre para queimar o álcool ou por onde sai o vapor????

Very nice

感謝

c'est quoi cette merveille. bravo j'adore

Anyone knows if have holes in the rings that he put the lines on?

i think this way less alcohol will be used with thes ame outcome

so there are no holes in the copper pipes and but the heated gas in the copper pipes under pressure blow the alcohol gas out of the 3 tiny pin holes.

このバーナーの銅パイプを真鍮にしたら耐久性は落ちますかね？

Nice

Very nice build! 🤟😎

Awesome

Muito bom...Eliseu / Brasil

There are holes for taking pressure gas from alcohol

Genial 👍 😁

Just 3 holes?

Great

Esses caras são de mais

Congratulations Saka moko

Sip lah .

show...show. ..show. ....obrigado

Muito bão....!