Setup Tip. Set Flight mode Switch Up Value 2000 (RTH), Mid Value 1500 (GPS) and Down 3D to 1400 (Will set to ATT Mode) so you will have Home, GPS and ATT Mode. Any time you make mistake in ATT mode you can switch to GPS Immediately. Make sure to take off in GPS Mode though after GPS locks all satellites and shows solid green LED.

Great video Ali! Your tips come in handy and make the FW helis more enjoyable to fly!

Thanks Ali, works great! Using a Horus X12S Tx I created a 4 position switch being able to use now all 4 flight modes.

Another good tutorial Ali.

Very nice rc heli sir..thanks for sharing

Thanks for sharing 🙏🙏

great Job Ali !!

keep up the good work Ali

Thank you so much Ali you're a bloody LEGEND mate. I've been wondering how on Earth to flip from GPS to 3D under the factory TX Values set. Thank you again. The Flywing Instruction booklet doesn't give up any information to this at all!

Outstanding! I have been waiting for this. I plan to use it. I have the same question as Eric. Can the ATT mode be assigned to the 3D switch rather than the GPS switch? I'd like to have Home/GPS/ATT modes if at all possible.

Great information. Step up with stabilization mode while learning skills.

Flying like this now. Only problem I have now is copter shakes bad at about mid spool up and spool down. I balanced both blades same center separately and together on a prop balancer, loosened and tightened the blades but still does it. Can’t tell if the shaft is bent but no crashes. Flies easy though. Thanks 😊

tks much made that easy

Te acompanho a anos. Parabens

That was interesting.

So i just changed my 3D mode to ATT (1400) on my huey . ive been flying in gps for several months now and am kind ig board with all gps mode can do. Im hoping everything goes ok in att mode. Im nervous about crashing but think ill be ok. If it goes well ,ill change it for my airwolf as well. Thank you for all the info and detailed instruction Alishanmao. I feel alittle more confident now.

Ali thank you 🙏

I love ❤️ this. I'm disabled and fly one handed, ÿes I fly with one ha , pinky on rudder index on cyclic.

Great vid as always. Using a Radiomaster TX16S, what values would you need to change on that radio to achieve the same outcome?

I just successfully set the 3D switch into the ATT mode. I used the same method Ali taught here. It flies great. 😅 Thanks Ali

Great job Ali! Can I Set it up with my DX18?

Excellent as usual, Ali. Very informative, clear and easy to understand. So, conclusion is, in “ATT” mode, altitude is held as well as “attitude”? Only thing lost is position hold? Correct? Thanks again, “Huey” Steve

Great!! Is this trick possible with version 2 of the FW450L?

Hello Ali, compliment for revealing us this secret, I've not tested it yet, but I have a rapid question, my FW450 is perfect in GPS mode, but only in downside mode, when I switch invert, it keep the postion (not as well as not inverted) but not the altitude anymore, I must give big corection on the collective to keep at a reasonable altitude. Have you never experienced this problem on any flywing heli ? All of the other functions of h1 seems to be perfectly working. Thanks

Hello, thank you again! I have a question: can one still use the " automatic" figures Circle and Eight?

Parabéns você é um gênio muito bom da pra fazer com o fw450?

😂 this is cool !

Hi Ali. Will this flight mode ATT work on the H1 heli or just the Lite? Thanks for all you do!!!

Good job. Any hack of binding or mixing a switch to control the head speed ?

Question is there a way to keep GPS assigned to the GPS toggle switch and just change the 3d toggle position to ATT mode , this way you could fly in ATT mode and if you get in trouble immediately switch back to GPS on the fly.

Great 'hack' Mr. Ali. Does the H1 use something similar to the SAFE function in Spektrum flight controllers? I mean is there a 'flight envelope' in stability mode (GPS)? So you can bank only by 45 deg or so? I haven't tried yet. Might also apply to '1400' ATT mode, or?

Can you give me a link please to buy a GPS AirWolf with calibration that doesn't need a laptop

is it possible to set the flight mode in Flywing RC Helicopter , Home -2000, GPS -1500 and (ATT - 1400 ) instead of 3D mode -1000 value in my transmitter. does it works ?

Do I understand correctly that in ATT mode the barometer is active and holds the altitude and the attitude sensor keeps the helicopter level? or is the barometer also deactivated?

what differnece between 6G and 3D ?

Ciao Alì...sempre belli i tuoi video..non conosco l'inglese e faccio fatica a seguire le tue spiegazioni...ma vorrei chiederti una cosa...ma volare in ATT cosa significa...che differenza c'è tra volo in ATT e VOLO GPS GRAZIE ALESSANDRO

Hiya, I replaced 3D mode with Atti mode, however I noticed yesterday during testing while flying up and down the runway there was quite a bit of tail oscillation. Is this normal? Can it be programmed out, if so will it effect GPS mode? Thanks

What happens when you switch from ATT mode to GPS or RTH mode during flight?

you have any info on the flywing fw450l v1.5 buddy?

Hi Ali is possible to set in futaba radio thanks

E invece volare in 3D oppure in ATT...quale è la differenza?..grazie

Hello, do you have to recalibrate on the H1 program once you put in 1400 on the TX?

First, MANY THANKS for Your VIDEOS, ALL OF THEM. About ATT Mode on FW450, that i learned WITH YOU, i tried and happen the followig: i was flying in GPS Mode and when i turned tp ATT Mode with the Throttle Stick on its normal position (on the middle) the heli went down immediately without maintaining the "hold" position as we can see on this video. Is it normal? Thank You again for your invaluable HELP.

on my bell 206 the ATT mode (1400) the helicopter dont lock altitude ?? why

Is there still the INVERSE Funktion wenn I fly in ATT Mode?

hi hun iv got a 450 l 2.5 i set it to att mode but when i flick the switch it drops like a brick have to go back to gps mode ddo i need to set other settings all so many thanks

Is this procedure the same if u in the U.S. ?

As Salam Alaykum warahmatullahi wabarakatul. I am interested in coming to the UAE

Hello Alishanmao, sorry to insist with the problem on my FW450 V2 abou "ATT Mode". I did what my Friend said about the Calibration of the Sticks and Switches on the radio ad H1 Program and the problem persists. when turning from GPS Mode to ATT Mode the Heli drops down, doi not stay in altitude. I don´t know if it is because one think that i remenber now, it means, my Friend always speak abou "H1 Version 1.9" and i'm recently using "Version 2.0" that Fly Qing says: ««H1 V2.0 New 3D security mode（Not 3D rescue，Just to prevent accidental contact with 3D during flight）: 1、This function has an adjustable height parameter, which defaults to 8 meters. 2、When this function is turned on, when the helicopter is above 8 meters, it can switch to 3D mode for flight. 3、When the helicopter is below 8 meters, the 3D switch is invalid and the helicopter cannot switch from GPS mode to 3D mode. 4、When flying in 3D mode, the helicopter will automatically switch from 3D mode to GPS mode and hover when it falls from a height above 8 meters to below 8 meters. If you need to fly in 3D again, you need to raise the helicopter to over 8 meters, switch the 3D switch back to GPS, and then switch back to 3D mode. 5、Please adjust the height parameters according to the weight and descent speed of the helicopter. If the helicopter falls too fast and the height set is not enough to make the helicopter brake and hover, there is still a risk of crash. Can You please tell me something about thisi sid? Thamk You.

Too bad, not complaining, The dummy pilot figure that should be included, Stringfellow Hawke doesn't have firepower to play with? Cannons and rockets. Fun looking whirlybirds.

My Huey is stuck at solid green LED - I cant unlock it to fly. Sticks down and to outside does nothing. Calibrating Tx does nothing. Using FS-i6S just like in this video. What do iI do? I need to fly! How to get flashing green LED?

I believe 6g is 1300, not 1200. that's what i'm using and may be why your 6g feels and looks like 3d mode ;)

Hello all, in my radio the value are displayed by presents from -100% to 100% how do I set the values to use GPS/ATT/6G positions

Why do they have a hidden mode ?

3d is............................... 6G Ali

How do I do this trick with my bell 206 and my Radiomaster tx16s?