Small power station Allpower power station completely disassembled. Information about battery and circuit boards.
Пікірлер: 75
@stevo2992 Жыл бұрын
Thanks for this, I've had problems with these power stations, most I've been able to correct (disconnect and reconnect, like a reset) that at least gets power to the AC outlets, but I can't get any DC power to the USB/C outlets, even the cigarette outlet, which according to the manual should have power available all the time. It's very frustrating. Looking forward to more of your vids.
@RahmatullahRezai Жыл бұрын
Sorry for kate reply. I will make another video soon. Then i will go over every components.
@RahmatullahRezai26 күн бұрын
@@stevo2992sorry to hear that. Have you checked the fuse? There are 2 fuses one is for DC output and one is for the Ac.
@solido3d9 ай бұрын
Hello, would it be possible to replace the battery with another lithium one of the same voltage but with more capacity?
@RahmatullahRezai8 ай бұрын
Yes . You can replace it.
@DanyzoO3 жыл бұрын
This is great, now I can dare open it and remove the mppt charging connector for an xt60 😊. Thank you very much for your video and insights
@RahmatullahRezai3 жыл бұрын
U need to adjust the mppt output because it's only 3S. The maximum voltage should not be higher then 12.6 😊
@jschreiber6461 Жыл бұрын
I had problems with the flimsy Anderson solar mppt connector as well, and intend to replace with an XT30 or XT60 or barrel socket as well.
@DanyzoO Жыл бұрын
@@jschreiber6461 for me the xt60 and a mppt for 3s lithium batteries from alyexpress and I can charge it at 100 - 108w maximum by solar charging
@jschreiber6461 Жыл бұрын
I checked its AC output with an oscilloscope and its 50Hz pure sine wave, 220V. Not modified sine wave, which would look like a 50Hz square wave and fail to start inductive loads, and this had no such problems. That said, its solar in and AC out connectors are really flimsy
@RahmatullahRezai Жыл бұрын
Yes you are absolutely correct. It's a pure sine wave. But it has a lot of distortion. 7ts Pure sine but not a good one :).
@maartenvanderveen6785 Жыл бұрын
I have this exact device. Its only operating when its on the charger. When the device is off the charger then neither DC or AC come on. I tested the fuses, they are good. I opened the device and checked all cables. Also good. I put the battery directly on a vectron smart charger. Its showing 14.4 abs charge, but no current (maybe BMS blocks it?) The device itself says its 40% charged. It doesnt seem to increase when on the charger. Anything i can try? Or declare it dead?
@RahmatullahRezai11 ай бұрын
Sorry for late reply. It's definitely the BMS. But remember it's 3s BMS. It's 3 cells in series'. The voltage should not be 14 volts. It's 3.7 volt per cell Wich is 11.1 volt in total.
@Cbridge9907 Жыл бұрын
Thanks for this detailed video. I have the S700 which after a few months of use will not charge via solar or A/C anymore. The USB C charger still works. This model doesn't have the fuse access as the one you used for this video. Have you seen the 700W model inside? Would you venture a guess as to what my problem could be? Thank you in advance.
@RahmatullahRezai Жыл бұрын
Hello. Iam going to check it out and find a solution to fix your unit.
@eskb19 ай бұрын
Hi, I have a Allpower r4000 UK version and from the first day the unit will not take a charge from the A/C or solar. Its under warranty, but Allpower never get back to you. Should I open the unit & see if the BMS is burnt out or just wait...
@RahmatullahRezai9 ай бұрын
Hi. Sad to hear that . But I think you should wait. Because the R4000 is more complicated than this one. I don't trust this brand. So don't be surprised if they don't reply to you. At the end if they didn't answer you. You can carefully open it. I am sure you can retrofit some other board that allows you to charge the batteries. Keep me posted if I can be of any help to you. Good luck 🤞
@eskb19 ай бұрын
@@RahmatullahRezai thank you, will keep you posted...
@petryrety2 жыл бұрын
Do you know how many battery is connected in series and how many in parallel for 606wh model? Is possible to increase battery capacity with external battery pack?
@RahmatullahRezai Жыл бұрын
Hello sorry for late reply. The battery are connected in series. There's 3s configuration. It's 11.1 volt.
@mhadzzul55402 жыл бұрын
My 666wh not working.problem with BMS.already wrote email to allpower but no solution from the company.can you help me sir?btw...great video sir👍👍👍👍👍
@RahmatullahRezai2 жыл бұрын
Hello. What's wrong with the BMS ? Doesn't balance or other problems?
@soginvl3 жыл бұрын
What is the safest way to disassemble the power station? Will removing the fuses help? Can you upload the rest of disassembly process? Your last video only showed the first half of the disassembly.
@RahmatullahRezai3 жыл бұрын
Sorry for late reply. Yes the safest way is to remove the fuses. When you remove the fuses you completely disconnect the battery.
@MrYoohootuber Жыл бұрын
Seems to be a lot of issues from these units. My USB C Stopped working in and output and I'm getting parasitic battery drain. I know it's 2 years old but thank you for the videos. I will try to open the unit and see if I can find the OEM part for the USB C port to see if I can repair or build a DIY generator using these cells. I won't be getting an Allpowers anymore. Their aftersales is non existent. They only tell you to buy another unit. My uncle also has a unit and also has a fault. Same response by Allpowers. ***NOTE TO ALL POTENTIAL NEW BUYERS. Read through all these comments and best go for another company for a solar generator.***
@RahmatullahRezai Жыл бұрын
Allpowers are using cheap quality products. Not recommended.
@henrickwesterink95392 жыл бұрын
Thanks for the infos. At the end of the video you mention that you would build your own power station. Ist the build video already released?
@RahmatullahRezai2 жыл бұрын
Hi. So sorry I have not released any videos. I will release more videos soon. When I get home from vacation. Have a wonderful day
@mickyp33573 жыл бұрын
I have a problem with my same power generator, the display has become very dim/ not bright so hard to see in daylight now. Has anyone a way of fixing this? Thanks.
@RahmatullahRezai3 жыл бұрын
The lcd display have a small led on the back. Maybe they LED diode failed / are about to fail.
@Kwestion36LondoN2 жыл бұрын
Mine has the same issue..... how did you solve this problem?
@Bamabrute85 Жыл бұрын
I have the same power station as this. All of the outputs work fine but none of the charging inputs work anymore. The battery is at 95% but I'm afraid to use it because i won't be able to recharge it. Any idea what could be wrong with it?
@RahmatullahRezai Жыл бұрын
Hello sorry late replay. If you still have the problem let me know i will make a video
@Bamabrute85 Жыл бұрын
@@RahmatullahRezai yes, I still have the problem. It won't charge through any port.
@ichbinderhamma851 Жыл бұрын
@@RahmatullahRezai I have the same problem😢. Can you help please 🥺?
@9829246959 Жыл бұрын
@@RahmatullahRezai I have the same issue - can you guide or help what can be done? all charging ports don't work.
@RahmatullahRezai Жыл бұрын
@@9829246959 sorry for not posting any video. Can you describe your problem? Then i will try my best to find a solution.
@goudhaantje35692 жыл бұрын
One youtuber could not charge the batteries upon receival. Ay tips for them and me. I today ordered one and hopefully it will charge on day 1. MAybe the battery is charged upon receival?
@RahmatullahRezai2 жыл бұрын
Sorry for late reply. The batteries were charged about 40 percent. :)
@Brit-One Жыл бұрын
I got one of these it was not working I told them they replaced it works fine, but they asked me to dispose of the old one I said yes because I'm a vapor and I know what sort of batteries are in it the batteries are fine I now have a tun of power for my vapes lol
@RahmatullahRezai Жыл бұрын
Just be carefu,l the 21700 inside the powerbanks are not rated for High discharge.
@germaineturnquest88923 жыл бұрын
The battery indicator on mine continuously flashes even after a reset. I have it completely open like in your video. Any advice?
@RahmatullahRezai3 жыл бұрын
I am not sure what could be the problem. I am going to check it out for you. Have you tried to remove the battery?
@mnhim001 Жыл бұрын
Thanks for the video. I have an Allpowers Monster X, which is no longer charging via the A/C anymore. Would you be able to help? All powers support is no longer available, not sure if they went out of business. I would really appreciate any help.
@RahmatullahRezai Жыл бұрын
Sorry for late reply. Have you tried to charge using USB c port ?
@mnhim0016 ай бұрын
@@RahmatullahRezai no power from the USB C port
@RahmatullahRezai6 ай бұрын
@@mnhim001 do you want med to make another video about the usb port?
@RahmatullahRezai6 ай бұрын
Ok. I will make a video about the usb port.
@FrankyN023 жыл бұрын
Didn't got which batteries are built in ? Is it 26650 ? Thanks for the video.
@RahmatullahRezai3 жыл бұрын
No it's not 26650. It's smaller then 26650. It's 20650. Which is smaller then 26650.and larger then 18650. It's in the middle.
@wand8626 Жыл бұрын
My unti is faulty and it doesn't have the two green fuses ( or holders) is this normal?
@RahmatullahRezai Жыл бұрын
Doesn't have any fuse at all ? Could you upload a picture?
@wand8626 Жыл бұрын
@@RahmatullahRezai Can't seem to upload a picture on here. If i take the fuse cover off the front there is nothing there, only the circuit board.When AC is selected one of the fans stays on all the time
@RahmatullahRezai Жыл бұрын
@@wand8626 do you know the model number? Could you check if you can disassemble it?
@wand8626 Жыл бұрын
@@RahmatullahRezai it's the S300 V2.0 ( AP SS-005) il try and take it apart and show pictures
@ibrahimchowdhury24692 ай бұрын
Did you resolve this .. I have the same model that shuts down when unplugged
@Vera777Dina2 жыл бұрын
Hello, I have the problem with AC and DC buttons, they are not working, but unit is working/charging, how to fix it?
@RahmatullahRezai2 жыл бұрын
Hello. The power station only charging? There is 3 buttons on the front side. No one is working?
@Vera777Dina2 жыл бұрын
@@RahmatullahRezai thank you for your reply, yes, AC and DC buttons are not working, when I press on them they are lighting for 20 seconds and then switching off by themselves, WiFi button seems to be ok and torch buttons are working.
@Vera777Dina2 жыл бұрын
@@RahmatullahRezai I have changed the fuses and now DC button started to work but AC still not working, any idea what to do?
@RahmatullahRezai2 жыл бұрын
Hello i will be back from vacation next week. I will check it for you. Maybe quick fix. But not sure. I will let you know when I get home. Have a wonderful day (night)
@Vera777Dina2 жыл бұрын
@@RahmatullahRezai Hi, DC button is not working again so I decided to buy another generator as this one is 3 years old and seems to reach the end of its life, but thank you anyway, best wishes
@chrispycriter66822 жыл бұрын
how do i reset it?the problem i have, it shows full charge an shows HELLO when pluged in to ac charger,unpluged the screen goes out and will not power up,great vidio,and sure hope you can help me
@RahmatullahRezai2 жыл бұрын
Hello sorry for late reply. You can remove the fuses there is 2 of them in the front of the device. If that didn't work you have to disassemble the unit. Hope it helps
@sheh1e1dil26 күн бұрын
Hi my AP is dead can you help me.
@RahmatullahRezai26 күн бұрын
What happened? Can you tell me?
@sheh1e1dil26 күн бұрын
@@RahmatullahRezai we felt a light electric burn, while it was solar charging and parallel a small fan on it. Then it was dead, no more charging solar or other.
@FrankyN023 жыл бұрын
Another question please: what is range of input voltage for charging this powerstation ? Thank you.
@RahmatullahRezai3 жыл бұрын
I will test it. For you. It's best to use charging voltage between 12.7 to 14 volt. Nor higher. If u want to connect it tl higher voltage then u need to use a charge controller. Mppt or pmw.
@exis2213 жыл бұрын
Oh my.. are sure it is modified sine wave?
@RahmatullahRezai3 жыл бұрын
It's kind of pure sine. But not true pure sine. I tested the output. If you connect sound system to it the sound system will make his sound. And I have tested the output which is not true sine.
@edwardbyard6540 Жыл бұрын
Chinese shit - 100% accurate. These units are junk.
@Deemon1 Жыл бұрын
Hello. Anyone know how to convert 110V US inverter to 220V EU into Allpower power station?
@RahmatullahRezai Жыл бұрын
Hello sorry for late reply. Do you have the us version? You want 220 volt out of it ?:)