Anyone else noticed that the video is 13:37 long? 😎

There is a clear and obvious reminder on the PSU cables for each brand that they are not to be used with different PSU's. That's all on you, modular psu cables are not universal or interchangeable, sometimes not even on the same brand between models. They specifically state that in the manual and box you get with the psu's.

A great video to remind everyone never to mix and match modular PSU cables, even from the same manufacturer and brand. Always use the set of cables which came specifically with the PSU. The pinouts for power plugs are standardised on the motherboard side, but they can be different on the PSU side, so using different modular power cables can cause electric shorts.

Hey Deb. Are you sure those pin-outs on PSUs are all the same between the Corsair and SilverStone units? Also, if you're up for it, open up one of the fried PSUs and see if there isn't perhaps a fuse that you can replace to get it up and running again as I'd expect that level of protection from SilverStone.

You're lucky you didn't fry your entire system

nice build. You got there in the end. Also, kudos for the ECU (Extreme Close Up) B-roll - very enjoyable. Your enthusiasm is infectious. Liked and Subscribed.

NOBODY: Silverstone: "Set Phasers to stun"

Sooo clean, nice build🔥🔥🔥

Your video editing and your smiles through the issues you had was awesome... Thanks for your vid

Your computers have dancing lights, gurgling fluids, spinning fans... My computer is covered in (both black & yellow Lab) dog fur. Excellent fireworks, BTW.

That introooooo. Skills!!! 👌

Awesome build! Love this case, just finished my first custom loop in it too :) Using the SX-1000 in mine because the SX-800 just couldn't handle it without chugging occasionally and that is a *titanium* PSU. The swap made my GPU coil whine go away also.

Wow amazing setup mam..I love it

Thank you so much for this video, I'm planning to do a build with the exact same case and motherboard size and i had this idea on mind

Great build and even better filming, nice work Andie!

Cool ! Thank you I enjoy this video

Love the Flt pump +Rad Kombi 👌

hi,its a beautiful watercooling custom pc build.And I have a question that whats the length between graphic card backplate and motherboard,cuz i wonder if its enough space for the asus c8i so.dimm card.thanks u.

Awesome Build! If you are not using the hard drive cage, you could try adding a second PSU in its place. An idea from a GGF Events Build.

That is some nice b roll. I liked how it was paced.

This is actually the same problem I encountered when I built my ITX secondary gaming PC as well, I wanted to buy the 1000w SS PSU however someone advised me to get the 750w corsair one instead, it would seems like this is as much as power you can get.

You are a trooper. I would have developed a phobia after an experience like that. Amazing build!

5:18 some of the cables are not extensions, they are directly plugged into the PSU, the pin out is different for a lot these and can cause a short even if they physically fit, but the build looks great! good job!

This is an amazing build! May i ask how you do the camera movements?

Holy shit this production !!!

Nice build

I love how you don’t give up

Just out of curiosity what are you using for a D-RGB controller for the EK products?

good work

really good

Beautiful Rig!

I just blew my Corsair psu last night while testing a motherboard-cpu before putting in the case. I accidentally used.EVGA cpu cord and the psu started smoking. The irony of it was a month ago I watched a video about why not to mix manufacture cords between power supplies.

What equipment do you use to film the B-roll? It looks amazing! Is it some type of camera slider or gimbal?

Custom cables can't be swapped between brands of powersupply. They have to be custom made for the matching power supply. Pretty sure that was the issue here. Great using the FLT120 though, thats what I came here for.

Is that the DDC or the D5 version of the reservoir

My favorite tutorial she not scared to show her mistakes and the fact she is still learning ..

Hey Deb, got a question about the loop. Is your loop like this: pump->radiator360->gpu->cpu->vram->rad280->distroplatte->pump? And did you use acrylic or petg? Your temps were „high“ with more than 60degress. I‘m asking because i have ideas for a parallel loop for the cpu+vram (same mobo and cpu) TY Cheers

So, you ended up ditching the Silverstone entirely and are keeping the Corsair SF750 in the build? Do you know what the maximum output / power draw is with your system when you are stress testing? When you were gaming? Thanks!

Cool!

If you have Corsair specific psu cables it's probably not a good idea to plug them into a Silverstone psu. They all have different pin-outs. On the Cablemod site you they are broken out by brands to avoid this.

where were you able to buy the vertical gpu mount I have that case and im not able to find it anywhere

Also - that upper SSD looks like the power cable is shifted to the right - needs to be straightened/aligned.

What cables did you get because I don’t know what cables to get for a sfx psu

Forgive me for saying this, but I am so happy someone else ran into the same issues I ran into during my first custom loop build.

Heavy components on a single radiator, performs good enough considering small case. What temperatures you thing you would get having two 360mm medium thickness radiators?

psu cables have standards and cablemod specifies what to use with which psu very clearly.....may be sff psus use diff atandard...... it may not be silverstones problem

Different psu cables are keyed differently. Seeing as how you're using Cable Mod extensions... They have a compatibility list for different cables and which PSUs they work with. Take a look at that and it will tell you which cables you can use with which PSUs.

how did u pull out the air of the pump? i think this combo unit is terrible..

high temp for a watercooled pc, with the res/pump+vertGPUbracket now you have "only" 240mm+140mm radiators (not so much for such high-end components), maybe more fresh air in the intake can help even more. BTW very good looking pc, nice work

Great video. Sounds like it was rough. I highly doubt the sf750 is the limiting factor, its been used by the sff community for insane overclocks and high-end parts without problem, it barely kicks in with my 450 watt 3080.

Is that normal CPU Temp?

I don't think the sf750 is limiting this. I have a 3080ti and 5900x both heavily overclocked and rock stable.

curious why CPU utilization @ 10:37 is only 17% but CPU temp > GPU temp

4000Mhz RAM? Doesn't that mess up the 1:1 infinity fabric ratio that Ryzen prefers?

Maybe the extensions were made for Corsair power supplies? Wouldn’t the pin outs be different on extensions?? I think you fried 3 PSU from using the wrong cables. If you wanted to properly test it you should’ve just used the stock cables to test first. I fried a PSU using a power cable from another manufacturer before. But I didn’t do it x3.

So what did you end up doing about your PSU? I ordered the Silverstone, and now am finding out that CableMod has discontinued all their Silverstone cables. So that kinda stinks. I'm thinking about sending this PSU back to Amazon and just going with the EVGA 850 GM (Gold PSU). those Silverstone are so expensive and only a 5 year warranty, but there's no other 1k watt power supplies in SFX. It's too bad Lian Li made this case to only accept a small PSU

Amazing work, but one question how often we need to change liquid inside,every few months or one time at year or every few years...anybody, I mean for best performance, I mean closed loop such as Corsair h150 or others, nobody change liquid inside and they have run a years with no problem, maybe little drop of performance but in loop like this I really wanna know....

What happen to you Andie? Where are you? I miss your videos.... are you all right?

Yeah after looking into this more, you fried 3 PSUs using corsair cables on a silverstone. The 6-pin SATA pinouts on different brands are almost always different. Silverstone: 12v, gnd, blank, 3.3v, gnd, 5v Corsair: 12v, blank, 3.3v, gnd, 5v, gnd Are your SSDs ok?

corsair power supplies are made by seasonic

You can link to the cutter that you chamfer at 1:47

How have I never seen this channel?

Lightning quick test!

Hi :) what about 15% cpu usage 80 c• degrees ?? To 120watts ? Custom watercooling ? Thats Insane.

Please read the ekwb leak tester manual first. It clearly states that one should not pump that much pressure into the loop (closed loop 0.3 +/- 0.05 bar).

You do realize that cable mod makes cables for specific power supplies? Which means that it isn’t going to work with every power supply. They’re specifically made for whichever psu you are using. You just got lucky that it worked fine with corsairs psu lol. So you literally blew out those three psu for nothing lol and yea 750w isn’t enough to overclock both cpu and gpu.

Did you know you can use a 160mm long PSU in that case

Good lord are you sure the cables are compatible with the PSU's you are using?!?! Don't hook anything else up before clarifying the PSU cables are compatible. P.S. the video quality and editing are top notch and miles above other videos.

CableMod do NOT make cables compatible with the SX1000 PSU... FYI.. Also your RAM is 4400mhz and you want to overclock it to 4600mhz 32gb??? I don't think that will work.

How did you manage to get the 3080?

Careful. Silverstone has a different pin out for the 24pin cable. Not all custom cables will work... Learnt that the hard way too. Also doubt it's the power supply that's limiting the OC. Try adding 5mv then OC the CPU a little. Let us know how you go...

I used to dream of having a build like this but after spending time under my car, the last thing I want to do is have to get under the desk too!!

Correction! Now THREE power supplies. You should know (but do you?) that different manufacturers have different cable pin outs and you can't just swap between them using any old power supply cable you like. Test thoroughly with multimeter and power supply tester. The information is in the motherboard manual, the internet and power supply manufacturer. Also, whoever made up you blue cables may have goofed up. Trust nobody's work, always check up first. Geez ....

i just had my silverstone take a dookie on me after a month....had it RMA'd and a week after getting my rig going again....... BAM psu broke the smoke seal again. i'm over silverstone anyrhing

Lol you do know now I suppose that you can’t swap psu cables. Po outs aren’t the same on the psu. Especially Corsair.

Not all custom cable work with all psus. This is common problem. I order custom cables with specific psus and never use different cables with different psus.

Hello.... what happen to you? You disappeared !!!! Missing you

You never use cables from other power supplys, even if there the same brand.

The supposed power outage looks sus to me. The background lights shut off one at a time, that’s not how that works.

I have most of the parts for this build. Except the 2 essentials that are impossible to find.. 5950 and 3090..

I hope you’re not trying to run those sticks at 4600

6:50 ouch.

😂 I guess plumbing is not your forte. However I fail to understand how it was possible to pass the air pressure test and then have a leak afterwards. And apparently also you don't understand that if a leak is present the first thing is to shutdown power supply , a leak and electricity present would most likely mean damaged components.

How much does it cost in total?

those psu cables obviously are not meant to be used w silver stone psus......should have taken a continuity tester and mapped the pins out

Damn she blew three PSUs because of using wrong cables.

👏 👏 👏 👏

Takes speial skill to toast two power suplies. Did you never think of testing thoroughly with a multimeter and power supply tester before connecting and powering up?

Not all PSUs have the same pinout in their cables. You can't just swap PSUs, even with the same brand. You must ensure the pinout on the cables is identical or you risk shorting 12V to ground. Frankly, you're lucky you didn't fry the PC...

PSU will just be a blown varistor, easy to fix, don't touch the caps

Most underrated tech tuber

Your pinouts are different on your cablemod cable’s not compatible with silverstone but compatible with corsair

3 units is user error. You didn't go back to the basics of the basics and dismantle your rats nest of a cable tangle, you've got a feedback or earth loop going on somewhere First clue, the pump not working on the cablemod cables but working on silverstone. Second Clue, cablemod cables work on Corsair but not on Silverstone. Heres where reality hits you and you can no longer blame silverstone for your mistake. For the 6 pin sockets, Corsair and Silverstone use a different pinout for the 3.3, 5v and Ground Corsair GRD 5 GRD 3.3 5 12 Silverstone 5v GRD 3.3 NC GND 12 Obviously, your pump isn't going to run when you invert ground and 5v, or 3.3v and ground, however this is not enough to fry the psu. What killed your Units, is that Silverstone uses a significantly differently pinned ATX 24+4 pin connector, while Seasonic and Corsair use a more similar (but still different) 18+10. SX1000 www.silverstonetek.com/goods_cable_define/sx1000-lpt-cable-define.pdf SF750 linustechtips.com/uploads/monthly_2020_03/corsairsf450.thumb.png.deee98794529d0f9c8450ec3b6e562d7.png Thor i.redd.it/hgjx48t6i6c41.jpg Make no mistake, the Thor will kill something at some point on the corsair cables, but it won't immediately show issues like the Silverstone would.

You look stoned AF lol!!

Yes. You can't use Corsair cables with a SilverStone PSU. And.... if you have a fully modular PSU, why ON EARTH are you using extensions?

Ridiculous

Kind of makes leak testing seem like a particulaly useful waste of time since you had TWO major leaks .....

Just use seasonic PSU and be done with it

Did you remove my comment or did KZfaq?

Awesome build!! Overclocking is over rated anyways!