I looked everywhere for videos on this and couldn't find any so I made my own. If you have questions...email me caseyjchapman@gmail.com.
Пікірлер: 30
@markbailey60517 ай бұрын
If you can see slots in the barring carrier, you are lucky because this means it was not installed backwards. To remove the barring from the carrier, slid your alignment tool into the barring and turn it sideways and slide it out of the slots. The carrier is designed to stay to be used again and again. If you new barring comes with the carrier then turn it sideways to remove from the new carrier and install the new barring in the existing carrier. Buy just the barring to save a step.
@lloydcisco30275 жыл бұрын
To much beer! The outer Bering holder for the Gimbel Bering don't need to be changed unless you spun the Bering in the holder just turn the Bering side ways and remove it takes 4 minute and you never ever grease any bellows. Always bellows adhesive and the hinge pins they use lock tite so heat the bell housing they come right out. I did this for 45 years factory trained you grease the shift cable bellows and that comes off you better have a good bilge pump or be able to swim good. this is y when I'm asked to go on some ones boat in always doing something.
@MrRunJump6 жыл бұрын
Casey, great video! loved the part about beer, very necessary, and besides being informed, I laughed a lot. thanks!
@Mudflap4968334 жыл бұрын
number 1 look at the destroyed outer ring of the new gimbal bearing great for holding your new bearing number 2 never grease a gimbal bellows use the right tools and use adhesive and you will not be doing it again after your first trip on the water
@agmc4me5 жыл бұрын
I feel you man. I had to drill 4 holes in my Aluminum ring and break it out in quarters. What a huge pain. Obviously been in there too long and corroded itself to the housing.
@davesenor31464 жыл бұрын
Great video! I'm really glad I found it. I'll search your others now.
@davesenor31464 жыл бұрын
Bummer there's only one lol. I still enjoyed it. Thanks
@seanc73275 жыл бұрын
I put a chain attached to the puller and put it on truck hitch, popped right out. After many beers that decision came about.
@vonsp216542 жыл бұрын
That’s a damn sweet pool
@larrysanchez2956 жыл бұрын
This is BIG LARRY Eton HOUSTON...thats a damn good VIDEO
@jimspencer11436 жыл бұрын
Just enough information to get someone in trouble. It would have been less of a headache if you drilled the outer face the broke it out then pulled again with the puller. Not using adhesive, how long did it take for the bellows to slide off and the boat sank. Bellows adhesive is cheap use it. The reason the hinge pins are so hard to take out it because of the locktight the factory uses. Hinge pins are what the bell housing attaches to the gimbal ring. They aren't the sender things.
@alibee19785 жыл бұрын
Beer has never been so fucking necessary for this job 😂 great video dude thanks for sharing. !
@mishlerman24336 жыл бұрын
Thanks for the tips! Great video.
@ajwilson18217 жыл бұрын
By the way thank you for a great video it is not easy to do, but you are very informative.
@brohardin5 жыл бұрын
ok, so why did you install the gimbal bearing backwards? 5:22 time mark the bearings in backwards.
@philippecomeau40003 жыл бұрын
Saw it too and thought to myself, this guy is not going to show me nothing haha
@brandonb7464 жыл бұрын
Too bad your bearing is in backwards.
@oczkowski82 жыл бұрын
Please help with links I appreciate this advice thank you
@pvtpelnar112 жыл бұрын
Does the gen 1 not have a gimble retaining ring for the joint bellow?
@willconwell Жыл бұрын
No. That was not introduced until gen 2
@coreycouch49426 жыл бұрын
Can you plz tell me where i can get the bellows at and bearings i have a alpha one gen 1 but i can not find any videos on them at all just yours luckly im replacing the tilt and trim limit and sender switches big job and how do i get the shifter back in place ? Like back in the out drive right
@caseychapman12736 жыл бұрын
that was a tough process for sure. i knew that i could get them from a local marina but they wanted a fortune. i ended up getting mine from a marine supply in florida. forgive me but i cant remember the name of them
@caseychapman12736 жыл бұрын
sorry for just now seeing this... as far as the shifter cable is concerned, i replaced mine. it was far too corroded to reuse. it is definitely a pain in the ass. the piece of cable that you will need goes from the throttle assembly on the side of the manifold through the transom. i think i paid about $90 for mine. definitely use the old cable to pull in the new cable.
@ajwilson18217 жыл бұрын
Does the Gimbel bellows on the gen1 have a clamp at the bell housing end or does it have a slip ring that holds it to the bell housing?
@caseychapman12737 жыл бұрын
Aj Wilson, are you asking if the bellows attach to the bell housing?
@caseychapman12737 жыл бұрын
Aj Wilson, the bellows attach to the transom plate. All of your bellows attach outside the boat. The large housing that is fastened to your transom is where all the bellows terminate. Nothing goes into the boat besides the shift cable
@ajwilson18217 жыл бұрын
Yes by ring or by clamp? I have the Gen 1
@caseychapman12737 жыл бұрын
Aj Wilson the gen one uses a radiator style clamp. The gen two has the ring you drive in for the gimble bellow.