ANSYS CFD Tutorial: Fluid Flow over a Circular Cylinder

No video

ANSYS CFD Tutorial: Fluid Flow over a Circular Cylinder - von Karman Effect

Рет қаралды 39,874

The Engineering Guide

Күн бұрын

Пікірлер: 36

@prachishah8357 5 ай бұрын

Amazing tutorial, very well explained, I could follow each step with so much clarity. Thank you :)

@AngelineTewaTEDOUNO 7 ай бұрын

Very explicit tutorial, thanks sir

@boyanpetrov9975 5 ай бұрын

THANKS A LOT FOR THE HELP!

@FelipeFadini 6 ай бұрын

That is awesome! During my college time I didn't have any professors with enough knowledge on ansys to show these simulations to us. I am doing one here as you did and so far everything is going fine. Do you have any videos similiar to this but with airfoils?

@amarsoni2832 7 ай бұрын

Amazing Sir🎉❤

@VipulKumar-bs5kz 2 жыл бұрын

Commenting here to grab your attention. I appreciate the good work and was looking forward for tandem arrangement of 2 and 3 cylinders. There are barely any videos for 2 and 3 cylinder arrangement so u making one would be helpful.

@theengineeringguide8332 2 жыл бұрын

Yes I agree! I will try to get the video up by the end of the week!

@mostafaahmadi4998 2 жыл бұрын

Incredible tutorial. Thank you very much for your time and effort.

@jakubgolc9296 2 жыл бұрын

great video, only drawback is that the volume goes up and down after cuts

@ajmech 2 жыл бұрын

How about a tutorial on Multi-phase flow ?

@Engr-Hassanshehwarshah 2 жыл бұрын

Dear Sir Please make video on fluid-elastic Instability behavior of circular cylinder

@f_forghan 9 ай бұрын

Nice video.. Could you tell me how to calculate the total force of hydrodynamic?

@saroj4736 11 ай бұрын

sir reynolds number is to be calculated at the cylinder diameter or edge

@muhammadzahirul235 3 ай бұрын

Can this be used in turbulence cases?

@seshireddyvenna4355 2 жыл бұрын

Nice exploration tq

@arbindacharya6465 Жыл бұрын

Sir can you please make a video on flow around an oscillating cylinder where the cylinder is oscillating in the y-direction... it's really necessary sir do help in this.

@engineered.mechanized Жыл бұрын

To simulate the acceleration of a thin tiny mm-scaled cylindrical pole under turbulent water flow, do I need to use CFD or FEA?

@BarryJones8 2 жыл бұрын

Excellent tutorial thank you for sharing. When looking at grid convergence, how do you pull the data from the analysis to create the comparison charts?

@livetoloveiist Жыл бұрын

hello, i'm working on a graduation research project about vortex induced vibration on an oscillating cylinder, could you please give me the needed UDF or setup to let the cylinder oscillate ? thank you best regards.

@joerivandesande1378 Жыл бұрын

I think the time step size should have been 0.004 instead of 250, because the von Kármán effect should not take this long to take effect.

@gloriamarceladebarrosmorae5198 Жыл бұрын

How can I calculate acceptable values for time step and number of time steps if my diameter is another and I'm changing the velocity of the water flow for each simulate?

@MADHUSUTHAN4072 Жыл бұрын

Let me know if you know

@joerivandesande1378 Жыл бұрын

@@MADHUSUTHAN4072 should have been 0.004.

@joerivandesande1378 Жыл бұрын

@@gloriamarceladebarrosmorae5198 look up Courant-Friedrichs-Lewy condition

@MADHUSUTHAN4072 Жыл бұрын

@@joerivandesande1378 well that's good...may I know the calculation aspect of it?