cool to see the functionality of these tail lights, only seen pics online

Thanks for sharing this video. I ordered them from Amazon, installed it yesterday (by installed I mean plug n play lol). They look awesome. 3 compliments from just this morning. I used led reverse light bulbs from F150leds (I got them as gift from them for a review). Thanks again for the video, it helped me make my decision.

Thanks for a great video. I installed my lights and followed your instructions. It went perfectly!

Thank you for using the blinker, that’s why I came here before buying me a set

Those look sweet on your truck. Seeing this, I may get me a set now!

Use alcohol spray and wipe the area before attaching the hardware

Trey. I knew you were from CA before I saw your LP. I would guess out in SOCAL, the San Gabe Valley? I will have to outfit my 2012 F 150 with those rad head and tail lights. Thanks for posting.

Thkz for the video. Very well instructed. I want a set for my 09 f150...thkz again

I had led's from Recon and after 4 years they were so corroded that they quit working. I hope the Anzos are better. How is the visibility from the rear? I can tell the brake lights are visible but how about the tail lights of you don't brake?

Nice truck man, I recently bought one with 8’ bed thinking it was unique but.. nope lol. In time I’ll be upgrading lights and suspension.

These are cool..may switch my aftermarket LEDs out for these

Where did you get that adapter boot that you connected the tail lights to?

I missed it! What happened to the 7.3?

After my years of being a automotive tech im not much of a ford guy at all, I like trucks that run. But they make a sharp looking truck. Ane a great video as well

Those are some nice headlights

I like it brother, looks good as well good job.🇺🇸👍

I'm dying to get these! *edit: 6 days after commenting this, I got them! lol.

Trey, how are they holding up?

Good vid had to like it

GREAT! Sold me on it bro. Getting these for my girlfriends truck. Thanks

Hey, any chance you could comment on the fit? I just got these and like them a lot however, one of them (drivers side) doesn't quite seat all the way even though all the holes line up. There's a 1/8" gap or a little more where you can see behind the tail light if you get up close. I noticed in your video that the drivers side didn't "click" into place and you gave it a few hits with your hand. Lemme know if you could. Thanks.

Does anyone know what the tail lights look like while driving ?

Hey are these still working for you, lots of complaints out there about them dying out after a few months or from water damage

Good looking lights..

Very helpful thank you

Sweet truck

They looked great! I'm looking into a set. Do you remember what size tires you had?

How are those Spyder headlights working for you? I have Spyder halo lights on my Ranger, but after about a year the protective coating is peeling off, making it look pretty bad up close. Have you experienced that on your headlights? Axial makes the same style light but are more expensive so I'm just trying to avoid having that same problem on the F150 I'm buying soon.

OMG, i was wondering till now if I was the only one with these tail lights.... :) Glad to know i'm not. They are great, after 1 year still looking good. The driver side doesn't fit too well, but not bad

Nice lights!

I have a 09 Ford platinum you think this will all fit for me like it fit for you

Do they still work fine? Didn't have any condensation or water in them after a year? I'm looking forward to buy those.

Wish they had those for the 04-08

where I can get this tail lights for my ford 2014?

Ik it’s been like two years but did these leak any water I’m thinking about getting them

look good

Can you send the link for the headlights you used? Thank you. The tail lights are sweet!

I bought a pair of them and my break lights didn’t work with them. Kept on faulting the BCM. Then i didn’t have any turn signals either. I’m not talking about hyper flash either. When clearing the codes and changing back to stock haven’t had the problem since. Pissed me off on the fact of buying them cause they do look sick but just can’t use them

Nice I'm planning on getting the same lights for my truck. It's good to see they don't hyper flash. Have you had any problems since this video

So headlights and tell lights or aftermarket but yet that third brake light is Factory you need to get the third brake light

As well do running bars with lights

Those resistors will be bouncing around in there after a few years.

Hows the waterproofing on these? Do i need to run a bead of silicone around them?

Amazon says it doesnt fit a 2014 ? Who to trust?

Would last one winter here in Canada. The bulb plugins are open to the elements. You would be better off to cut and heatshrink the wires together.

Update please?

Thank you very much i like it 😍

Did U Have Any Issues With Water 💧 Condensation

Can you tell me where to buy it?

Have you had any issues with them filling up with water?

Loooks 👍🏻

You've had these a while now, what do you think?

Are they still working? Any moisture/water in them?

Put led kits and foglight and as well led 3rd brake and license plate lights

Did you have a gap in the lense just installed them on my truck and the quality is terrible

should of cleaned it off not just wipe the dirt

How much did you pay for them? Just for comparison sake.....

روعه

Put your twist lock the old bulbs were in back in the housing

force scan??? just buy led equalizers at auto zone for your blinkers flashing too fast

Plug and play?

These look like they actually belong on the truck and were factory.

Bruh u were supposed to put the plugs into it like they were on factory with the bulbs. It's a seal

don't you think you should have clean that off with some alcohol before sticking those boxes in there LOL

No limpio bien el área donde coloco la pieza.que mal

And what you shoulda of done is show us the difference with the originals on (first, BEFORE YOU TOOK THE ORIGINALS OFF). Then show us your REPLACEments afterwards.

LOL dude a couple of glaring errors there ya numpty! First you need to clean off any areas you are using adhesive tapes, a good clean and then alcohol! Secondly the sockets that the bulbs used to fit in but now have the connectors need to be mounted to the new housing like they did to the old, you dont leave them dangling and have gaping holes water and dirt can get in!! Take your lights off and use the bayonet mount to clip the bulb holders where they go!!

there's only 3 LED's one at the point and one on each leg of the backwards "C" shape. send em back... ESPECIALLY FOR $350.00!

You breathing killing me. Star make some exercise 🤣

Listen I can tell you right now in a month or so you're going to be hearing some rattling going on in the back of your truck and those resistors are going to be bouncing around because you didn't bother to clean the surface that you're trying to stick them to just saying.

Nothing like scratching the hell out of your nice new lenses. Not preping surfaces, for the ballasts. Glad your not a professional installer

I jus don't like these, them plain leds that are on should be the stop lights, and them BUNCH of leds on should the tailights, I'm jus saying.🤢😳👎 No good.