AORUS WATERFORCE X 360 with LCD display AIO liquid cooler Unbox install test

Рет қаралды 22,336

it care & computers

8 ай бұрын

Thank For Watching
Guys Hit like and Subscribe Feel free to ask any Question about this video

Пікірлер: 32

@WarlordDestroyer 6 ай бұрын

I'm not sure why some say that the fan cables are connected the wrong way. I've had problems making GCC to recognize the ARBG fans since I got my new PC. It was this video that made me undestand I had the fan cables wrong. One of them was connected to the fan of my Case and not among the actual AiO Cooler. I was able to make it work taking a look at this video. Now GCC is displaying the lighting profiles as it should. It was about to be a full year of controlling the ligting through the Motherboard. Actually, I haven't seen another video that shows how they go connected without making you confused when the cables tangle to each other. The only bad point is that there's no voice telling you why which cables goes to which other. Thank you, man! This helped me a lot.

@itcarecomputers 4 ай бұрын

Always welcome

@Hydeny13 3 ай бұрын

so the cable with ARGB connector still covered like on his hand in 8:56?

@abdulmajeed-mg5jy 8 ай бұрын

keep it up bro ❤

@jrbatista7804 Ай бұрын

Very good 👍

@user-jl3nz2ts9u 4 ай бұрын

Each fan 3 wire for?

@x5e2 7 ай бұрын

Hello, can I put any video I want if there are specific things?

@remustodeanca492 6 ай бұрын

Hello! If i lost the usb controller the rgb will not work? Where can I find the usb controller? Thank you!

@linkdestructgames4824 7 ай бұрын

thx for the video! but the 3 fan cable doesn't have to be conected to the male conector on the bomb? afterall, the bomb has 3 male conectors. why did you conect the last one on MB instead bomb conector?

@picasso8253 5 ай бұрын

because he has to connect it to the motherboard what kind of question is this lmao

@hansen9604 5 ай бұрын

Ich habe alle kabel von der Wasserkühlung verbunden und kann RGB steuern doch die Drehzahl der Lüfter kann ich nur die letzten beiden Steuern der erste Lüfter quasi über dem Display dreht gefühl fast auf Max und ist dementsprechend laut Selbst wenn ich alle Lüfter ausstelle dreht er immer noch gleich und die anderen beiden gehen aus Woran kann das liegen habe das letzte Kabel was vom Koppeln über bleibt bei Aio pump angeschlossen Wo ist der Fehler ?

@user-wi2sr6yh6n 6 ай бұрын

What GPU is that?

@tcevatt50 2 ай бұрын

terrible video of wiring the fans and AGRB. Not exactly sure how to connect these properly.

@albertogilgoni3414 7 ай бұрын

hi! thanks for the video. Can you tell me what is the cable you plug in the minute 9:00 for? Thanks in advance

@itcarecomputers 7 ай бұрын

That one is fan cable that connect with cpu_fan header

@robiruzic 2 күн бұрын

@@itcarecomputers so any of those connectors or hast to be specific one out of three??? to be pluged to mbo and those female connectors at8:45 one has 4 pin two others 3 pin that's my concern and can i connect it(or all three ) INSTEAD OF MBO TO CONTROLLER??

@tahsinanan147 6 ай бұрын

does it show cpu and gpu both temparature at the same time together like nzxt kraken does in one screen?

@itcarecomputers 4 ай бұрын

Yes

@Mosaic3321 3 ай бұрын

Bro plz help I facing this type of issue Please install AORUS LCD Panel Setting Tool😢

@musicislife7512 3 ай бұрын

Ok now try to change the pump speed .....

@nerijus01 6 ай бұрын

your video is a bit misleading regarding connections as you do not need to connect any fan to the cpu header. All it needs is a usb connection to the motherboard and sata to the psu and of course all the connections between radiator and fans.

@shanamaynelimbaco7189 4 ай бұрын

I was also wondering why 1 of the fan is running off-sync with other 2

@beanschannel2313 3 ай бұрын

Why would you not need to connet the fans to the cpu headder? Isnt the water cooler connected to the cpu, isnt that what the fans are trying to keep cool is the cpu? Isnt that the way to control the fan speed for your cpu is by conecting it to the cpu fan header?

@Fernando-ns9iz 3 ай бұрын

Tipo então eu não preciso conectar as ventoinhas no conector da bomba eu devo as conectar na placa mãe? Então as 3 conexões da bomba não precisa ser usada correto?