Great video bro! You really help us a lot newbies fly better!

Thank you for great set up video. And the equipment list. keep up the good work.

I know your last response was one year ago, but this is a great video you have produced. There is no way a person could screw up this installation watching your video explanation. Thanks so much for your video. I bought recently 2 of these units, one for AR Wing Pro and other undetermined at this point. But the way the markets are now days and how long it takes to get controllers its always best to buy 2 at a time. Keep up the great vids.

Thank you for doing this video!

Thank you so much for this video ,it is so helpfull 👍

Thanks for the great video, one question, can the system work with a 2S batt (7.4V)

just got one , Thank you , Video helps a lot !

Hi nice video i used your video to setup the dragonlink ppm but not getting the output signals from the arkbird

Nice tutorial, thanks for that.I am quite new and have a question my bix has 2 aileron's the arkbird 1 why????? And do i have to use a y splitter. Thanks a lot

great informative video. nicely done

Thank you from the bottom of my heart for such a detailed video ! I am new to FPV planes. I will connect the Runcam that I bought a year ago. Can I send the video to googles, and if so which one do you recommend me? Greetings from Greece !

Good video, thanks! I am a bit disappointed that you did not show the Fence and Waypoints programming....

Excellent ,helpful video,thanks

Thanks for the video trying to hook up arkbird light can't find an instruction manual or video on that one

Couple quick questions. On a Flying Wing with no rudder I would assume you would omit the rudder (from Arkbird-to-Rx). Also do you set up your model in the Transmitter as a standard plane (A,E,T,R) and the Arkbird does the mixing

Excellent video 👍

What current sensor do you have to use the 4s battery? The one of hobby king says it is only for the 2.0 system.

Hello, how you connect a Quanum Elite 600mW 5.8GHz 40CH FX718-6 AV Transmitter And Camera to Arkbird?? Thank you.

hello, very interesting video ... I have a problem the gps does not work, do I have to buy it original or is any gps module okay? ... thanks 

I have a Spektrum DX6 for my twinstar. Would it work with the arkbird? Or does it require more channels? (DX8 or 9?) No pan/tilt.

Thank you for the video sir

hi nice video can you tell me how to get ppm working with arkbird and dragonlink

As you go, friend, I use the Arkbird OSD with 3S battery, but I intend to use 4S battery, how do I do it, just connect to the voltage sensor or do I have to make any changes?

hi. is this autopilot suitable for a fishing boat? how many points can it remember by GPS

whats the cable for the current sensor called? cuz I just bought the whole pack of airbird osd but the cable for the current sensor didn't come with it. thx.

Hello, thanks for your replay. Did you ever test the RTH by switching off your radio? So, what way did you set your values and curves, from -80 to +100 or something like it? greetings, Ruud

How do you calibrate the milliamp percentage I flew yesterday and it said I only used 495mah I actually used 1409mah 3s 2200mah gens ace battery in a bixler 2

my mode symbol is stuck at a triangle and will not switch, do you know what is wrong?

Where can I find the vtx cable? The one you have is a vtx with a servo pin. Did you make that? Or can I buy that. Most vtxs doesn’t come with that type of connector.

Hi, can you explain me why "no gps" with 9 or 11 satellites? I don't understand! Thanks!

Can the Tiny Arkbird be used on a vtail ?

Hi, is this autopilot compatible with telemetry. Can be used on baitboat?

Excellent video. Will this system work with a FlySky TH9x 9 channel radio setup? Thanks

Thanks for the great info. ik have a Mini Talon myself. where did you get the tiny fpv screen?

This is the video i have been looking for , simplifies everything , thanks. Just one question , i have a dx6i , no triple switch ,how do i get around that?

What if aleron are on there own line for flaperons and separate flaps for crow breaking

Hello 7demo7. How would I go about setting up the arkbird for a skywalker x6 wing. I know i have to switch button 4 on top but where do i plug in the 2 servos. I used to have it set up on my bix 3 and it worked fantastic. So i can't wait until it works on the x6 wing. Thanks Sean.

+7demo7 Where does the pan and tilt servos for the camera plug into if I was running a pan and tilt setup?

Hi. Many thanks for the great video. I have followed you step by step but for some reason I'm not getting power to my vtx when I go through the Arkbird. If I use a separate power supply then it makes the servos twitch. Would it be possible for you to clarify what colour cables go were for the vtx ? Many thanks 👍🏻

Sir i would like to purchase this FC but i am wondering where i can find a detailed step by step written manual on how to install and setup the arkbird

thank you. what you think for the Airspeed Meter?

can this FC run with Sbus. i am looking to purchased this FC or the MFD Crosshair Autopilot.

how would this work for a flying wing... Could I still set up the channels through the arkbird

Awesome man

Great video! How do I connect the ESC pin in case I have 2 motors?

hello I have a new arkbird already connected all the chips but not works I have to do something before you install? thanks

What is that white pc you’re using too help set everything up?

Hello I'm interested in the artbird V3.. is there anyway I could use this just for OSD purposes only I will be connecting this to an helicopter . I have my own FBI unit and 2.4 transmitter. Is there any way you can hook this up without using any of the servo ports and use it for just a OSD. Thanks

The ark bird will work with a variety of monitors ?

Hi Jeff...I have a question. At 8:45 you plug in the video power, red in the middle, black at the bottom. Then you flip the plug, and you say something about the orientation being right, and then red becomes bottom and black in the middle, right? This is the part that I don't get. If I measure my Arkbird the right polarisation is red + in the middle and black - at the bottom. But...if I do so, my OSD stops. The camera (runcam night eagle) turns on and gives an image. Do I need to switch the red and black like you do? Seems strange, since when I plug in a selfpowered camera with only the yellow at the top and the black at the bottom OSD and camera image are just fine...now (before I blow up my runcam) any suggestions? Thanks in advance

Hi Jeff!! I have correctly installed my arkbird v3 1028 thanks to your tutorial, but a problem has arisen, the question is that when I put the stabilized mode on, the rudder and the pich do not work. I don't know how to solve my problem, can you help me?

how would i conect my pan and tilt?

I have a question about your gyro settings...did you leave at 100%? my fx61 gets a elevon flutter at high speeds

Would you still recommend the v2 or should I still wait

I got everything working like it should, but can"t seem to get video feed through the arkbird controller. I am getting the OSD just fine on my screen and I can connect my RX/TX to my goggles not going through the controller and they work just fine. I changed the OSD parameters from PAL to NTSC and still no video feed through it. Any ideas?

Hi, Need your advise again !! All ready for maiden all surfaces going the right way in manual mode, but in stabilize mode elevator going the wrong way ? any idea what i have to do, been at it for yonks !

Sir what version OSD are you using for this demo?

You said you set it up as a v-tail later. How do you wire that? I'm lost. It comes out of my dx8 as throttle right aileron right elevon left elevon gear left aileron How to you wire that to the arkbird?

how do you monitor rssi?

hi mate. im using a v tail do i have to switch v tail mix on my radio as well as the arkbird?? thanks

Hi great video can you answer a few questions 1.i have the Arkbird version 1 when I'm gyro mode it bounces m.kzfaq.info/get/bejne/e7xyept6qpvGnGQ.html 2. Im thinking of getting the ezuhf module for my taranis does the Arkbird have ppm or is their a uhf reveiver that does pwm for the connections Thanks

Do you have the Arkbird Nano?

Thanks for the video. Almost everything work great. The only hang up is with video. I have a Foxeer Monster v2 camera and a Readytosky 5.8ghz FPV 600mW TS5828L transmitter. When I hook up the red, black, yellow plug from the x-mitter and the same for the camera, I get a black screen with Arkbird OSD info. I have to unplug the yellow wires and hook them directly together to get a video feed but then lose Arkbird OSD info and am stuck with Foxeer OSD info. Any ideas as to why this is? Both the camera and the xmitter are working, just not when the video signal goes through Arkbird. Does the jumper have anything to do with this issue I'm having? Help from anyone is greatly appreciated.

Hi, love your vids. first time talon build with arkbird installed cant get the 4s current sencer been on backorder at h/k for 6 months can i run the arkbird on 4s using a bec.? or do you no ware i can buy the c/sencer from ? many thanks, Kevin.

Make a part with the AAT part also :)

Holy SHIT!!! I bought this assuming I can KEEP my flaps, where to I plug in my flaps?

You still happy with this? I have been thinking about getting a cheaper RTH to put in another plane. Cheaper than eagletree that is.

Awesome video My Arkbird has Chinese Language, can you tell please how to set it to English?

Ok thank you.

Support PPM?

I buy a fpv.

Arkbird has NO support....they do not answer emails!!

like