Shows the Ark Ezi guide boat alignment system - that guides your boat onto the centre of your trailer every time - whatever the weather !
Пікірлер: 27
@hosko648 жыл бұрын
Just back from two weeks fishing the Mid North Coast had the Ezi guide fitted before i left The best thing I have done I fish by myself it makes it so much easierI wish i did it years ago.
@GraphicwrapsAu9 жыл бұрын
Yeah!.. Like you said.."Should have fitted them years ago".
@lerch1229 жыл бұрын
they work well,even put my 27 foot boat on by myself
@Slazmoservicing42093 жыл бұрын
Ark, you need to make the roller tip guides less rubbery, lots of failure and they don't last.
@wayneburns3947 жыл бұрын
I have purchaced a second ezi guide with the intention of fitting it half way up the trailer I believe this will give me 2 points of contact and ensure the boat stays totally in line with the rollers when power loading please comment if you don't think this idea is workable
@Radswa_Chikinora6 жыл бұрын
wayne Burns how has having two sets worked out for you? Is it much better than the one?
@MrAuldphart8 ай бұрын
I’m in the process of fitting mine today. As per the fitting instructions, i have taken the spring out and fitting the roller to the rear cross member which is probably a little lower than most trailers I have seen. So when the roller is tilted up to contact the hull, only the tip of the roller makes contact because of the angle, I have adjusted the sliding u bolt bracket up as high as it will go. Is this ok for operation or will it damage my hull?
@shaneconte432810 ай бұрын
Wouldnt buy again the rubbers dont last 12 months, fell off the other day and scratched the whole underside of my boat 😢
@hookinggoodfishing2245 Жыл бұрын
With they showed how it was fitted to the trailer.
@kittybellrosecritcher7542 Жыл бұрын
Can you do a installation video
@luiseduardobentaberri80112 жыл бұрын
Donde compro los componentes para que me lleguen a Uruguay... gracias
@luiseduardobentaberri80112 жыл бұрын
Hola que procedencia tienen esas guías???
@Johnnyreengo Жыл бұрын
The AAAK easy guide
@kyliezammit808 жыл бұрын
Are they used for the boat to be centred on trailer when retreiving?
@CTFxFROGGY7 жыл бұрын
u show we buy
@graemeswanson63492 жыл бұрын
I have a Quintrex 4.2 wide body dory. Unfortunately the rollers kept getting caught on the ribs of the boat. I just cant get them to work and have removed them. Has anyone else had the same issues?
@mattp5843 Жыл бұрын
Yeah mate, my rollers keep flipping the wrong way, boat doesn't like up properly on retrieval, lack of rollers at the front. Looking at getting some ezi guides to assist, it turns me off boating tbh.
@johnjargon15497 ай бұрын
Yeah same. Doesn’t work on hulls with strakes or raised channels extending all the way to the transom as the rollers get caught on them and are not able to flatten onto the hull.
@CTFxFROGGY7 жыл бұрын
would be better to show how to put them on ur trailer, not just an AD get smart, show us how to put them on any trailer
@korndawggy18017 жыл бұрын
Romulus Tiberius they come with directions.
@1PricelessShot3 жыл бұрын
I reckon! Every boat is different t
@supernelsonkiwi4 жыл бұрын
I took mine off, the outside roller wore out in about 4 months and fell off in the water, the pin left gouged my Hull getting the boat up without it, would be better if it was just one long roller without the 2 little ones.
@ARKCORP4 жыл бұрын
Thanks for the feedback, unfortunately it can’t just be one long roller as there would be an exposed bracket on one end which will come in contact with the hull. If you need replacement top rollers, please get in contact with Ark directly sales@arkcorporation.com and our staff can assist
@supernelsonkiwi4 жыл бұрын
@@ARKCORP thanks for the reply, if I put them back on I will try use a different roller, mine have gone really soft.
@keithdonald95224 жыл бұрын
A long roller failed on mine and the other is cracked. Good idea but they damage your hull when they fail due to poor roller materials
@deaconcsvic29692 жыл бұрын
I had the same issue with the top roller falling off. I had the end corner of the metal shaft in direct contact with the hull and cost me with repairs. I had to angle grind the end of the metal shaft off to avoid further damage. Needless to say I have trashed the system.