Assembling the JUKI DDL-8700 Step by Step

Рет қаралды 132,889

5 жыл бұрын

So you bought a Juki DDL-8700 not fully assembled? Well have we got a treat for you! In this video, you will watch a certified, industrial sewing tech as he assembles this machine step by step. We shot about 40 minutes of footage, but chopped it down to about 12 minutes. You may want to pause the video as you go along. We hope this helps! We also hope that you will visit www.cutsew.com in the future for your industrial sewing needs. Thanks for watching!
We do offer the unassembled version of the Juki DDL-8700 at www.cutsew.com/Juki-DDL8700--...
Special Thanks to Royalty Free Music from Bensound

Пікірлер: 59

@halimashillingi9283 11 ай бұрын

This has been the most helpful video I've ever watched thank you.

@morgannjay2401 3 жыл бұрын

Thanks so much! Would have not made it through the assembly without this video!!!

@saidulshikder7940 4 жыл бұрын

Nice video 👍👍👌👌

@marrizd 4 жыл бұрын

Thanks for sharing this very informative video.

@dilankengmo301 Жыл бұрын

❤ c'est très bien

@raquelirizarry5857 6 ай бұрын

What do you think about that sewing machine? I want get one but I don't decide yet. They are good quality?

@ruthwilson7451 2 жыл бұрын

I just bought a juki 8700 and I'm having trouble with the belt that seems to be too tight the flywheel is a bit too hard to bring towards you. How do you loosen the belt?

@user-ti1dg1mk2k 4 жыл бұрын

شكرا

@nounou6749 4 жыл бұрын

Good

@CutSew 4 жыл бұрын

Thanks

@lluviaysol3083 3 жыл бұрын

Hellodesde Perú

@omegaglover 4 жыл бұрын

Do I add the entire bottle of oil? And do I have to let it run for a certain about of time before I use it for the first time?

@CutSew 4 жыл бұрын

Omega Glover fill the oil bath to a level between high and low. Before threading and sewing on the machine, run it at a higher speed to ensure that the oil is pumping up to the top. You should see oil splashing through the clear oil window on the top of the machine.

@DrStephanieMillerWilliams 4 жыл бұрын

Two questions...Are the holes in the table pre-drilled? I have a Sailrite Fabricator industrial machine that I am disassembling, would my Juki 8700 & 1181n (I bought both) fit in the Sailrite Fabricator table? Thank you! 😊

@CutSew 4 жыл бұрын

Hi Stephanie, Most of the holes in our table are predrilled. The threadstand hole must be drilled. As for the Sailrite table, I have no idea. Sailrite is a manufacturer and distributor of its' own brand. No body sells it but them, so you might want to reach out to their support.

@DrStephanieMillerWilliams 4 жыл бұрын

Cut Sew Thank you! 😊

@tdodo3026 4 жыл бұрын

Hi. Thanks for the video. I have a question please. There are two 1/2 half circle rubber with some dimples on them (time frame stamp is 4:33-4:45). Do you know what they are for? I don’t see you use them. Thanks.

@CutSew 4 жыл бұрын

Yeah, those go under the rubber bumpers that get nailed into the table. You may want to check out our more in depth video on how-to assemble the DDL-8700

@CutSew 4 жыл бұрын

Also, those are really just shims in case the table top got milled out a little deep. They don't always get used.

@mat-yy5uu 2 жыл бұрын

I have a question, regarding a long spring inside the head of ddl 8700 machine. I bought the machine in surplus store and i discovevered that long spring already broken at one end and the other end can be found fixed at the back part of the machine, inside. Can you please tell me what is it used for? My machine has no tension release when i use the knee lifter. Thanks in advance. God bless.

@CutSew 2 жыл бұрын

I think thats a tension spring.

@fefemtshokotsha3013 4 жыл бұрын

Thanks for the video.Can you please advise?my industrial sewing machine drive belt is making noise when I sew. How can I sort this?

@CutSew 4 жыл бұрын

So many possibilities...Have you tried tightening the belt by adjusting the motor mount?

@fefemtshokotsha3013 4 жыл бұрын

@@CutSew thank you for the reply.I will try that

@fefemtshokotsha3013 4 жыл бұрын

@@CutSew you won't believe what happened.As I did according to your instruction.I discovered a teaspoon on the drive belt.My daughter was playing past week around the machine.With her toys.

@patriciamirgorod313 3 жыл бұрын

Does the plate of the bobbin slide easily to remove, or it is meant to be slide with machine tilted?

@CutSew 3 жыл бұрын

on the 8700, it should slide out without being tilted

@kongalla.tirupati.jai.bala2969 4 жыл бұрын

Good.ra

@sahidachowdhury7018 2 жыл бұрын

Line up screw to flat area I don't where the screw

@Symia722 2 жыл бұрын

Every drill I use to screw the belt down didn’t work

@simonasamaru6055 6 ай бұрын

Avete uno anche per la Juki DDL100?

@saidulshikder7940 4 жыл бұрын

Hi brother 👋 Juki mol 254 ,, video,, more ,,

@sebastjansslavitis3898 5 жыл бұрын

is this servo motor?

@CutSew 5 жыл бұрын

Sebastjans Slavitis, yes it is. A dial in servo motor.

@subowosubowo7112 4 жыл бұрын

Bajed berapa di indo Mr.

@abouzarmajidi4195 4 жыл бұрын

Merhaba

@moziburmozibur7226 3 жыл бұрын

how much Bangladesh price

@sawaireniwal4714 2 жыл бұрын

Hello

@kongalla.tirupati.jai.bala2969 4 жыл бұрын

@miridagama1177 4 жыл бұрын

Quanto custa?

@CutSew 4 жыл бұрын

Depends. See DDL-8700 page www.cutsew.com/Juki-DDL8700-Single-Needle-Lockstitch-FULLY-ASSEMBLED-READY-TO-SEW

@jaybharat4738 4 жыл бұрын

Havmac praec

@madhavpathi1281 4 жыл бұрын

How much this

@CutSew 4 жыл бұрын

Fully assembled is currently priced at $750 before continental U.S. Shipping is applied.

@CutSew 4 жыл бұрын

We made a much more involved, very detailed, DDL-8700 Assembly video so you won't miss a thing. Make sure to subscribe to our channel & check out the DIY Juki-DDL 8700 1 hour video here kzfaq.info/get/bejne/rreEfKx8s7imgYU.html