Somebody needs to tell FCP to correct their video! They didn't even show this. Great job.... I had this same problem btw.
@Infantryman6622 ай бұрын
The FCP video I watched they said it but didn't show it. I missed that very important bit of information and had to take off my supercharger again. Which was not that difficult or time consuming to do.
@lrw555 Жыл бұрын
Greetings from England, this video saved me. Had some work done and had intake fault codes pop up on both sides. I forwarded the video to mechanic, problem solved.👍👍
@mr.padgettt Жыл бұрын
awesome! Glad it helped you out
@kevinwonsetler37776 ай бұрын
@mr.padgett5927 how did you correct it? New part or just unstuck it.. do you have part numbers?
@kevinanton4150Ай бұрын
Thanks bro. Would been nice to know this before the fuck up lol
@markmorelli6602 Жыл бұрын
Thank you for this video, having this problem at the moment
@aceanthony70562 ай бұрын
Thanks for taking the time to pass the information on
@quinnvineep3 Жыл бұрын
Thank you so much man, had p2006 and p2007 after I did my carbon clean on my v8 s5 and sure enough it was this exact issue.
@yonex47112 ай бұрын
You have safe me thank you sir
@JOATiDetermined7 ай бұрын
Thanks for the video! I had the exact same issue on my 3.0T powered Audi SQ5. I was able to correct the flap issue just by taking it apart and diagnosing the issue before stumbling upon your video. I have since corrected the mechanical flap install issue. However I am now still getting the fault codes for both sides saying they’re stuck closed. I tested the intake, manifold runner control valves by hooking up a vacuum pump and letting it sit for about five minutes to simulate the vacuum system on the car. The flap actuators appear to be working fine. All electrical connections and vacuum lines are connected every time I clear the code and go for a drive it comes right back. I’m wondering if perhaps having them installed and properly and the vehicle being driven if that caused an issue with the actuator? Looking for any advice as to what this issue could be thanks.
@redbrown5721 Жыл бұрын
I had this code after doing thermostat and it didn’t seem to drive any different. Guess I’ll just pull the super charger for the 5th time
@kevinwonsetler37776 ай бұрын
Did you fix this? I had same issue after water pump..thinking maybe something wasn't sitting correctly
@redbrown57216 ай бұрын
@@kevinwonsetler3777 yep it’s the flaps u have to hold them open when putting manifold back on
@kevinwonsetler37776 ай бұрын
Thank you. I currently have it at the mechanic. Said 2500 just for parts..2 months out. I think I will get it back and tear it apart again and check this out
@kevinwonsetler37776 ай бұрын
Is there a way to check to see if they have failed?
@adamvu1199 ай бұрын
It’s a common mistakes when no one read the shop manual 😂 I make same mistakes but got corrected before install supercharger
@yurboymoose Жыл бұрын
Hey bro, nice videos I have a question about your FZR600. I have a 97 and have not been able to find any fairings anywhere at all. Do you have any idea where I can or what other year or model fits it?
@mr.padgettt Жыл бұрын
no idea. i just grabbed blank white ones from ebay and made them work
@yurboymoose Жыл бұрын
@@mr.padgettt gotcha alright then I’m gonna order 250 or 400 set and hope it’s the right thing 🤣 thank you 🙏🏼
@kevinwonsetler37776 ай бұрын
How did you fix it? Just manipulate them?
@marcmills93149 ай бұрын
What happens if not fixed ? Also what if your car throws this code but goes away and keep coming back on its own
@kevinwonsetler37776 ай бұрын
Is there a position sensor? Or is it integrated in the manifold?
@K24-SRT9 ай бұрын
What is issue if the intake manifold flap is stuck closed ?
@cruzfernandez4554 Жыл бұрын
Hi, I have an issue with one of the actuators not holding the vacuum. Can I only replace that part? Please advise
@joerrelsaguin4550 Жыл бұрын
My issue as well. Bank 1 A intake manifold stuck open. My only solvable idea is to by the actuator on the side that is faulty. Most likely the actuator froze n broke on you. If so I would change both to be safe.
@maheshub Жыл бұрын
I have audi a8 3 tsfi, have error for flap stuck. Is this the solution? 😊
@K24-SRT9 ай бұрын
Awesome video can the actuators be replaced without removing the SC?
@mr.padgettt9 ай бұрын
not to my knowledge
@K24-SRT9 ай бұрын
If you can move the actuator arms manually up and down this means the air intake manifold is installed correctly, the issue is something else like a vacuum leak or a faulty actuators? Because I'm getting a fault code intake manifold stuck closed bank 1 and 2
@1bads58 ай бұрын
See this is BS... i did mine right and getting the code on both sides