BTW, do you have the old rear cans sitting around from this car still? Curious of the overall length from tips to back of resonator....? Thanks man.
@JoeyJazeSmith2 жыл бұрын
how is the sealant in the engine mount holding up. I was waiting for 034 motorsports aftermarket option but it seems that their prototype never made it pass final quality control so they abandoned the project.
@muckman5509 Жыл бұрын
I wished you showed how you made the hangers. Everyone forgets to include this in the videos
@EastCobbTodd Жыл бұрын
That cricket is pissing me off
@daviddelvalle23402 жыл бұрын
Where did you get the custom piping?
@muckman5509 Жыл бұрын
How hard was it to adjust your hangers?
@primesoodangerous36412 жыл бұрын
Which tune are u with
@smellynyangnyang2 жыл бұрын
Any droning in cabin?
@calvinasiimwe7297 Жыл бұрын
What size tips
@pavelppp8882 жыл бұрын
Hello, can you provide the link where you bought the 3.5' tips from? Thank you! I think doing the same on my 2013 S8. the tips should be the same, right?
@Nash-Vegas2 жыл бұрын
I would also like to know!
@krallopian2 жыл бұрын
@@Nash-Vegas @Pavel Petkov they look like Yonaka tips, all over ebay and amazon for years now :)
@jameshammond39682 жыл бұрын
What tune do you have and also how did you go about adding a pops and bangs effect? I’m going to be purchasing the DS1 tuner but I want to add pops and bangs to my 18 S6 when in sport mode. No one has really made a video of how it sounds with pops and bangs nor how to do it so that would be awesome if you could touch on this subject more, I’m sure a lot of c7 owners are looking for a way to do this but just have no answers or examples of it done.
@dgk_recordings2 жыл бұрын
I have pops and bangs with my 2016 S6, just ran downpipes to free the sound up. You could play with the tables in DS1 but you really shouldnt have to. Factory did a great job with overrun on our cars once you let the exhaust breath more freely
@jameshammond39682 жыл бұрын
@@dgk_recordings yea no for sure they def did my thing is that if u tap the throttle once or twice or so it cuts the burbles for a while
@calvinasiimwe7297 Жыл бұрын
And link?
@Stpetersburginjurylawyersmp2 жыл бұрын
Where did you get the tail pipes? I was going to replace the mufflers with Borla muffler's so it's not too loud, I already removed the resonator.
@Customwerx2 жыл бұрын
I make them
@douglaswells27392 жыл бұрын
Those are nice welds! 45 bends in 2.5"?
@Customwerx2 жыл бұрын
Thanks! Yes that’s correct 👍
@douglaswells27392 жыл бұрын
@@Customwerx I like using a 4" exhaust clamp on the old pipe so I have a way to mate up the new pipe and hold it in place/rotate it as needed for alignment. One can ultimately weld it up or keep the clamp but a great way to get things precise. Do you think you would have had enough room for a short 10" resonator and those tips in the space you used with the straight pipes?
@djidroneuser52712 жыл бұрын
This makes me miss mine so bad. Totalled mine earlier this year due to a deer :(
@MidwestMotor2 жыл бұрын
Insurance? Getting another one?
@djidroneuser52712 жыл бұрын
@@MidwestMotor got 36,000 but ended up getting a 2021 jetta execline since my insurance was 850 a month 😂 Fortunately I’m now only paying 200 a month
@Customwerx2 жыл бұрын
Sorry to hear man..
@BlackYellow_s72 жыл бұрын
Do you get fault codes since the rear mufflers valves aren't plugged in?
@Customwerx2 жыл бұрын
You will have a soft code stored if you scan the car
@jay_2168 Жыл бұрын
You don’t get a check engine light when removing the active exhaust sensor?
@Customwerx Жыл бұрын
You get a soft code
@pepemedel44202 жыл бұрын
what size is the pipe that you are installing? diameter?
@Customwerx2 жыл бұрын
2.5”
@robertdaone Жыл бұрын
Did you notice any loss in torque from having less back pressure?