i am the same way lol

That's the plan!

i think it is a 22 gpm pump was thinking of upgrading to a 28 gpm

@@OutsidewithScheib 28 would be excellent if you got the ponies, how many horse is that motor?

@@cowshottv5867 15hp right at the limit

Oh yeah!

thanks harry I am liking it so far

My pleasure!

We are definitely paying attention Kenny! This channel, along with a few others, is one of our favorite channels (along with the comment sections) to keep up with and get insight for our machines from the people that put them to the test. We do have log lifts and worktables available on our site and are working to create even better machines for the future.

No doubt!

I think so too!

Thanks 👍

Thank you! Cheers!

Thanks, you too!

Thanks! Will do!

Thank you

Working on it!

Pretty much!

Surplus center for the valve Amazon for the tee and any hydraulic shop should be able to get you a hose made but I got mine from discounthydraulichose.com

Thanks!

The A and D ports will be Tied together at the Rod end of the cylinder with a Tee the B port just goes to the clevis or welded end. Then your power beyond if you get one would tie into the other valves but then you will need a return for the autocycle valve itself which would be tied in with your main return with a tee or get a sae16 plug for the power beyond port and tie the return into the other valves like I basically did. if you don't get the power beyond you just tie the valves together like normal.

@@OutsidewithScheib thank you

Yep it’s at Sam’s wood yard

HT-12-ASB | 3/4" HYDRAULAX TOUGH™ Hydraulic Hose Assembly HT-12-ASB Fitting #1: FJX90-12-12 | 3/4" JIC 37° Flare Female Swivel 90° (FJX90-12-12) Fitting #2: FJX-12-12 | 3/4" JIC 37° Flare Female Swivel (FJX-12-12) Overall Length: 4 feet 0 inches amzn.to/3QmsTH0 And an auto cycle valve you will have to make a mounting bracket for the valve.

The problem with the log lift is the holes in the ports are 1/4 inch and they have 1/2 inch lines going to it it’s a lot of restriction. Not sure yet I’ll have to look

non power beyond RD523MMEE5A1A1 power beyond RD523MMEE5A4C1

this is a 30"

It’s a prince auto cycle valve

Eaton Aeroquip 2028-12-12S Male... www.amazon.com/dp/B008I5PP2C?ref=ppx_pop_mob_ap_share www.surpluscenter.com/Hydraulics/Hydraulic-Valves/Directional-Control-Valves/Prince-Auto-Cycle-Log-Splitter-Valve-RD523MMEE5A1A1-9-6587.axd HT-12-ASB | 3/4" HYDRAULAX TOUGH™ Hydraulic Hose Assembly HT-12-ASB 1 64.83 $64.83 fitting1: FJX90-12-12 fitting2: FJX-12-12 orientation: none inches: 48 protection hose-label: no

Pretty much all you need. Remove the current valve put the auto cycle in its place run the hoses and your done.

@@OutsidewithScheib I am also a little uncertain. I ordered my 700 series and it should be here any day. I already received the prince autocycle valve just waiting to install when splitter arrives. I got the one with power beyond not really knowing if I would ever use it. Can I use the existing hoses as long as I get that plug or do I have to get the extra hose and T and all that also. I am confused

Andy when I bought this machine I had intentions of putting an adjustable wedge on it, all the other stuff just fell into place as I seen to make it better for my application. Doing the adjustable wedge saved me at the time 3k from a Wolfe ridge. The log lift from factory could be put on either side. The rear tow point is necessary. Cost was nothing. The new landing gear or support leg is a much better design and was needed in conjunction with rear tow just to be able to put a trailer jack on. The auto cycle with all parts needed was roughly 600 bucks . So I would say it isn't homer built just a Frankenstein machine with ideas from other splitter designs.

@@OutsidewithScheib my comment wasn't meant to put your splitter down.thr fact that for a few bucks and hard work you were able to make a splitter comparable to a Wolfe ridge is more of my point. It started as a rugged made and has evolved

I didn’t take it that way at all your good brother lol 🤘🏻🤘🏻🍺🍺

I do it was one of my first ones so it’s not that great. kzfaq.info/get/bejne/fJ6mn5SVscDRmIk.htmlsi=a5dhYqibcta5L0xf

I have had tis splitter for 4-5 years and haven't had a single major problem with the machine. if you take care of it it will take care of you.

cost about 600 but could have been 500 if i would have opted out for the power beyond

its a prince valve

What parts are you looking for exactly?

@@OutsidewithScheib I have the exact splitter as you, so the auto-cycle valve, all the new hoses and the T connector?

surpluscenter.com non power beyond RD523MMEE5A1A1 power beyond RD523MMEE5A4C1 the tee i got from amazon www.amazon.com/dp/B008I5PP2C?psc=1&ref=ppx_yo2ov_dt_b_product_details The line i got from discounthydraulichoes.com 4.5 feet long with a 90degree 3/4" jic and a straight 3/4" JIC but if you have a hydraulic shop near you could be cheaper.

hold a beer

@@davidellis4746 😂😂😂 🍺🍺🍺🍺

I am sure it will be once I get use to where the levers are located again lol