I had an 01 Maxima a couple of years back and had a very similar problem, it turned out to be a bad MAF sensor. Replaced it and it ran perfect!

Don't give up Randy. This is content we like to see.... Please check the MAF sensor

Also check the IAC. Idle Air Control valve on the throttle body.

The 2000-2003 were the last of the “good maximas”. They definitely went downhill after these years. Not sure about the newest gens, but they have CVT’s.

My friend. I got a 2001 Maxima and it used to got the same codes that in yours. The P1320 is not a problem with the coils, the problem is with the IGNITION CONDENSER (located in the main harness just above Cylinder4) and the P0300 can be caused by dirty fuel injectors. I almost sended my baby to the junkyard thanks to that codes that caused rough idle when you put the car in gear. You can still save her man!

Randy you should hire an assistant to organize the projects and keep you on a schedule 😂 if you're hiring let me know 😁👍🏾

Randy...chech and clean the MAF...the trans also uses the MAF also for the trans...its also could be the reason for the misfires also..the ECU is not reading correctly from the MAF and causing that issue. Also check the PCV valve..had a car doing the same thing and it was a stuck PCV valve...but anyways good luck....and greetings from Puerto Rico....watch you vids all the time

Check the catalyst, I had a problem on my maxima (2007) in the “transmission” because it didn't work well because the catalyst was covered and did not let the gases out of the engine. Finally, remove the bad catalyst and it worked perfectly. maybe is your problem

Definitely seen that problem from the vehicle speed sensor being faulty. Known issue with DE-K cars. Clean sensor or replace. Easy fix. Weirdly the MAF can cause the same issue but is less common. Id try the vehicle speed sensor.

It is probably the ignition coils, on those they have a specific type of coils to use, and on the wire harness there is a ignition condenser on the wire harness that might need to be changed as well

The last good Maxima were these. They weren't the same after. Thanks for the video, Randy.

Not every one is a success. Given the number you have brought back letting one go to save others makes sense to me. Great video once again. So many out there waiting for you.

I have a '99 Maxima, with essentially the same drive train. I had a shop pull the transmission to repair an engine oil leak. When I got the car back, the transmission did this exact same thing. With nearly 250,000 miles on the clock, I feared the transmission was done. A deep Internet dive led me to check the shift linkage. It turned out that while the shifter showed it in "Drive," it was actually half-way between drive and neutral. A 30 second cable adjustment fixed it. I've gone another 1,000+ miles since, and NO issues. May not be YOUR issue, but it is a place to look.

This brings back so many memories, my 02 would do the same shifting BS. Never did figure it out, after 4 new transmissions and running out of warranty money, Nissan bought it back.

I don't think it's the transmission, it's going into limp mode for some reason 🤔

Had one of those cars with the same problem. The pins on the connector to the abs pump gets loose and causes a bad connection which caused it to limp out. Open up the pins to get a tighter connection. That solved my problem.

Willing to bet with the throttle sensor causing it to stall out, since you can restart automatics in neutral, It got dropped from neutral to drive while being revved to keep it running, and or maybe they two footed it at stops to keep it running and burned out the clutch packs in the transmission, very harsh firm first gear shift says a lot, Maybe I’m completely wrong, But we’ll never know. very sad for this little car to say the least, This car was before this cvt nonsense of 2007.

Yes she's worth it please don't give up I got a 2000 GLS non spoiler striped Nissan Maxima best damn car I've owned since my gen 1 1980 Toyota supra u will go through 3 transmissions before the the engine gives out yes I had to get another used transmission but been okay ever since

A long time ago I had the exact same Maxima in pearl white, the intake gaskets leak and cause it to refuse to idle until warm (in which case they begin to seal shut with heat and the car will progressively idle better). I tried a new MAF, cleaning the throttle, cleaned the IAC, camshaft sensor, etc. It's those gaskets, it's a very common issue on these after 140k miles and it solved all my other issues once I changed them. Beyond that I can't wait to see the Citation get cleaned up and painted!

great video Randy, you did your best with the car and I commend you for it. you can't always bring all of them back. you are one of the hardest working people I know 👍👍

I ended up junking my maxima for this same problem. I thought it was throttle sensor too. Definitely curious to see the problem is.

Randy this maxima needs a crank shaft position sensor and AutoZone sensor's won't work on this engine that's why the car dies I had an 2003 with the 3.5L engine . It would drive then shut off.

A lot of vehicles take several drive cycles to relearn idle strategy after replacing TPS

You will need to place a volt meter on the leads of the TPS sensor and adjust the new TPS sensor to read as closest to12 volts for it to ride smoothly

Why is a Nissan maxima acting like a 2009 Malibu is the universe trying to tell us something😳

I owe a 2000 max had same misfire had to replace all 6 coil packs and plugs. Change mass air flow and best to change all shift solenoids now I am at 400k miles and counting .

The reason trans isn’t shifting is the speed sensor at the wheel I promise you I’ve had 10 of those

If both sensors still throw the same code check the wiring for the sensor omeit out check for resistance stop just throwing parts at it

Really not much can go wrong with those Craftsman Mowers, I know that type of machine like the back of my hand I have modified them diesel swap them and more. But if you get into tuning and clean the carburetor it can be fun. Personally, I took a Bolens Tractor that was sitting for many many years, luckily it was put away correctly, just put fresh gas to the carburetor it fired right up. Now the fun process of replacing fuel lines and cleaning the fuel system, but not the carburetor luckily.

To adjust the TPS you need use electrical tester on oms and it needs to be .5 volts closed and 4.85v when full thottle use the signal wire for positive and negative to a ground and adjust as needed to you get voltage right @auto auction rebuilds

Keep trying man. I enjoy your videos: I would try to replace the ignition coil and also try flushing the transmission too.

Randy never give up on a car they will be back alive sometime

The 02 03 Maxima with the VQ35DE and 6 speed is the best generation. Well to me it is. It’s maybe not as reliable but a great 4 door sedan. I bought one with a blown head gasket and in the process of rebuilding it.

Thanks for making these videos, all the content is great, plus the good comment section.

Good luck hope you an family are doing great. Buddy see you soon

I own two 4th generation cars, one is straight gas(petrol), and the other is propane and gas(petrol), and yeah, I have replaced the coils and MAF sensor in both, crikey mate, poor man front wheel drive Skylines now, 32 mpg now, or better, at 25 mph no bullshit mate 👍

Cam sensors mass air flow coolant temp sensor.

Love the content like always Randy !

I have a 2001 maxima, my son was driving it one day at college and he came to a stop and the car just shutoff, started right back up but as soon as you put in Drive it stalls again. Later I came to visit . He had some help pushing it to the side of the road out of the way. I came up there and started it and it idled find until it warmed up and put in gear. my scanner had no codes for it. I just SWAG , l of it disconnected the TPS and it idled at 1800 rpms and stayed running. He then was able to drive it 1/2 mile back to apartment where it was parked for 10 days until I could come up next. What I did next was with my scanner verified the TPS was fine. and it was. I wasn't going to do anything with the Idle Air Control . I then did a quick and dirty Throttle Body cleaning with a shop towel, tooth brush and TB Cleaner. this was after I removed the Air box to get to it. I also shook out the filter. which didn't look good. Put it all back together and it idled fine even after warming up. drove it a little in parking lot and it was ok. since I was alone I didn't want to risk getting stuck I just parked it back, and also put in a bottle of high mileage Fuel Injector cleaner. in tank. about a week later had time to go back to evaluate driving it 2 hours back home. during this time we had gotten better newer used car. were were unknown what to do with the maxima at that point. but was willing to give it a gamble. Since I noticed the Air filter didn't look good I had ordered a $5 air filter from amazon and just change it out. it couldn't hurt, and if it didn't help I would only be out $5. anyways. drove it around after that some and then proceeded to drive 2 hours to my home. and it made it not even a check engine light. before this all started, I was going to do a front brake pad replacement and rear struts replacement and had already purchased the struts (2 rear quick struts $72 off amazon, when they came it was really Duralast brand however on amazon they were branded as TOPAZ. the same identical parts if purchased at AZ would of been 212 instead of 72. so what I really think caused it to stall out was a clogged air filter and or some dirtyness in the TB plate the car has 243k miles and has had a transmission code p0744 for 4 years now living 2 bottles of Lucas in addition to a 3x drain fill of ATF to get it to move under its own power. and has been drive 41k miles after it started.

nice video. why not send it directly to junkyard. I think you get the same money after fees etc..

Literally to the 1% who's reading this, God bless you, and may your dreams come true, stay safe and have a wonderful day.

could be a weak fuel pump. Injectors not getting enough fuel hence possible misfire then the limp mode

there is a transgo shift kit that might fix that transmission, check it out. around $50 bucks online.

When I had an 2003 Maxima the crankshaft position sensor needed to be replaced. It would die randomly in stop and go traffic. That was in 2008, faulty design at its finest.

I have a 2011 Accord, and the starter motor was going bad. If it took more than 1 second to start, the car ran like total crap. No acceleration, misfiring, etc. Put a new starter in and it runs like new.

Looks like someone kicked the front quarter panel. Previous owner who got tired of it ?

You gave it an all American try. Atleast we know what it might need. We can't win them all .

Randy my dad had a 97 that would do that and all he done was had the intake cleaned along with the throttle body.

I threw a bunch of sensors at an Nissan Altima with the same kind of issues and it never did shift right. I swore off anything with the CVT after that

Shift Solenoids block ? see NTB00-039d power steering fluid leak onto exhaust was the smoke ?

If it has a separate TCM it uses the crank sensor Data to determine shift points if it has long crank time and shift issues something to Look at.

Yes MAF sensor

Randy I was having issues with my nissan murano. Thinking it was the tps and other things. Turns out it was some simple. It was the air breather hose had cracks and holes I didn't see. That was the problem the whole tim. It did simular things that yours is doing. Maf sensor could cause so.e of the same issues as well.

This one’s perfect for the mail lady!

thanks..... but more time can solve the problem ......check other sensors.......

That trans is definitely broken sounds like a bad clutch It could be a dirty MAF sensor as well

Did it actually blew a gasket while sitting or did the waterpump took a dump?

Randy you shouldn’t buy anymore cars until they up for sale just trying to help out . I had a 1992 Sabaru Legacy it was my grandmas she passed away in March 17 2003 she gave me her car. It sat in my driveway for years it needed a battery 2011 we tried to start it fired right up. It needed a lot of work to be done to the Car. I got rid of it. Awesome video 😎😎

I have seen several times in your neighbour's garden and in your videos, an Audi A6 which looks a lot like the one you had. Is it yours?

Listen to the people who comment on replacing the MAF sensor my friend! Cost to fix both the shift solenoid and MAF sensor was less $500 if you do the work yourself, at least for me it did!

Shift solenoid going from 2nd to 3rd gear. Change that and it'll be fine.

I really want that Chevy Citation!!!!!!

My friend's Maxima had several bad fuel injectors so I would check them.

MAF? Check all vacuum hoses and add fuel octane cleaner fluid?

P1320 is ignition coils, had all the same problems you had

Check the coils, if it's missing bad due to several bad coils then it will go into limp mode. Coils are a weak point on this model.

You think you would check the fluids

Sure, you can do it!

Check the crank pulley and the vvt solenoid

These use a different intake from the Maximas from 1995 to 1999, 2000 they upgraded the intake

Good morning Randy!!! Subscriber since 2017

Randy great video. Brother you did best you can on the old girl you can't save them all but be proud of trying and giving them a little more life then they had before you got them

Any help ? Before I change the VSS AND MAF my only codes are showing

Please make a video on the craftsman tractor! Maybe your channel will become like Mustie1 !

Tighten the ground cable for starters. What fight?????

Same tranny issues with my 2000. Had wiring harness replaced, speed sensor and it would run for awhile before going into limp mode. Used it for in town travel but did not trust it for long trips.

I’m willing to bet that intake hose before the maf is cracked causing a huge vacuum leak. That or the maf

Having similar issues with my 2000 se maxima and when driving without rubber duct on throttle body (only way it runs and stays idling) the car won’t go past 2k rpm’s and sounds like crazy misfire. But doesn’t seem to have issues shifting NO HARD SHIFTS

Does the Ford Model T horn go ahuuuugaaa

Good content with this maxima Im an auto technician myself for Nissan Infiniti and let me tell you if I was you I would fully restore the car and maybe sell it the engine alone can last over 400 to 500,000 miles pretty much stock i’ve seen a VQ30 DE with 499,999 on KZfaq..

Try shifting in manual mode If it doesn’t shift-it a trans issue

When misfiring many it will cause limp mode....while in limp mode it will cause the tranny to be limited to avoid causing damage the tranny

I have one I bought it for 400 I just swapped out one coil pack and it ran normal and it’s been my daily I recently resealed the engine and put in a vortex suppercharger

Your Chevy situation might be a 1980s model idk I looked up some information the car first came out in 1980 what year your car is idk I figured I'd share this with u good video

Put some corvette tires on the tracktor

In your Nissan Maxima it is not your throttle position it is your master airflow sensor and everything is going to start acting a one

My golf Mk4 did the same thing its a transproblem

I had a similar issue with mine with the transmission, turned out to just be that it needed a fluid and filter change.

It’s a great body style but no telling what the gremlin is inside of it.

replace the o2 sensor a bad sensor will make ur car go into limp mode

Did you try replacing the mass flow air sensor that can also cause it to misfire and not right because I have a 08 impala LT that had the same issue and it was the mass flow air sensor

Transmission range sensor is bad. It doesn't know what gear it's in. Hook it up to live data and shift it. I bet it shows the wrong gear.

Transmission speed sensor and revolution sensor to just went through all of this on my 2002 Nissan Maxima

just a heads up with older nissan Hitachi is oem.

I would buy it if I lived closer to you and 2.5 swap it, clean up the paint and drive it till the wheels fell off lol

I was hoping that sensor would fix it but i guess you can’t fix them all bummer!

Ok this one has some severe issues man that smoke it looked like it was comeing from the transmission or the engine was overheating

there is a shift silnord that might be going out

Hi Randy, those are wheel covers you have for the Citation, not hub caps! Heh by the way wat is up with Monkey Wrench Mike, is he posting, not seeing anything

Whatever happened to the Chevelle you took on Power Tour