Awesome $50 Tiny Spot Welder - Better than Expected - 1031

  Рет қаралды 462,155

My PlayHouse

My PlayHouse

3 жыл бұрын

I was really impressed by this tiny spot welder, that I was recommended by one of you.
I bought this from banggood but it is also available from other places.
[Affiliate Links]
From Banggood - shrsl.com/3l7vv
Amazon Link - Tiny Spot Welder - amzn.to/3Qd93Nl
__________________________________________________________________________________________________
/ myplayhouse
For 3$ a month, you get an extra weekly "What's UP" update video. Just for my Patrons. The Support I resave on patreon is all used on stuff to make interesting videos on KZfaq.
My PlayHouse is a channel where i will show, what i am working on. I have this house, it is 168 Square Meters / 1808.3ft² and it is full, of half-finished projects.
I love working with heating, insulation, Servers, computers, Datacenter, green power, alternative energy, solar, wind and more. It all costs, but I'm trying to get the most out of my money, and my time.

Пікірлер: 786
@RandyRandersonthefamous
@RandyRandersonthefamous 3 жыл бұрын
I'm glad technology is becoming precise enough for a PORTABLE spot welder! I've also noticed the new lower voltage tools are extremely efficient.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Thas was way better and smaller then my previous tries.
@emiel1976ep
@emiel1976ep 3 жыл бұрын
I have a similar spot welder. It is crazy how good it works. I tested it only yet, and I am impressed. Mine has an USB a 5v 2 amp output on the back and less on the front that shows the battery power. 9 power modes and as I see yours, it works the same with setting up. I love it. The rubber casing is a good thing. I think that I print something from tpu to protect the spot welder.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Sky man Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@supergiantbubbles
@supergiantbubbles 3 жыл бұрын
Fantastic review. I really appreciate that you took it apart to show the internals.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Dustin Skye Thank You very much! It will actually be shown again in about a hour in todays video :-) Thank you for watching! :-)
@zachreyhelmberger894
@zachreyhelmberger894 3 жыл бұрын
@@MyPlayHouse I just got it in the mail from Amazon for $72 and all I had to do is press and hold the button and BANG! I got little solder leads on my tiny CR927 Li-ion coin cells and soldered them onto my logger board's RTC clock and set the time.
@sunnyokapi
@sunnyokapi 3 жыл бұрын
I was about to say the same! I was very curious what kind of batteries were inside and assumed 18650s so I'm glad that was cleared up
@ndoghouse6853
@ndoghouse6853 11 ай бұрын
FYI: They are about $140 now. There are others of similar quality for under $60. I already bought another but that one seems really well built. I do like the bus bars across the mosfets and the heavy duty battery connections. Well done and thanks for the info.
@MyPlayHouse
@MyPlayHouse 11 ай бұрын
Thanks for the info! they keep changing the links :-(
@thedave7760
@thedave7760 9 ай бұрын
@@MyPlayHouse I wish there was a way to change the delay till the weld is triggered. mine seems to just go as soon as it shorts, I wish it was about one second.
@testingandtrackdays8651
@testingandtrackdays8651 Жыл бұрын
I have a very similar spot welder to this. I improved it by modifying the electrode cables. Replaced with copper ones and hard wired them to the the connections on the board. Way better performance now.
@MyPlayHouse
@MyPlayHouse Жыл бұрын
Hi Testing and Track Days Thank You very much! glad you liked the video :-) Thank you for watching! :-)
3 жыл бұрын
I am using such a spot welder now quiet for some time. I paid only USD 26, maybe because I live near to China. I do a lot of spot welding. I therefore can confirm that you weld at least 250 spots before recharging the box. I wish you happy welding. You can replace the copper welding electrodes by simple copper nails.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Renato sa Camiguin Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@elfpimp1
@elfpimp1 3 жыл бұрын
Where do you find your copper nails???
3 жыл бұрын
@@elfpimp1 In any good hardware store or even on-line. Just google "copper nails". Take a magnet with you because some shops sell fake copper nails made of steel.
@tomas_klouda
@tomas_klouda 3 жыл бұрын
Would you share the link for the one you have for 26$ ?
3 жыл бұрын
@@tomas_klouda Mine is not available anymore. But I found a similar one at a similar price: www.lazada.com.ph/products/agoal-spot-welder-portable-6-gears-adjustable-mini-spot-welding-machine-for-18650-battery-spot-welder-spot-welding-machine-tool-kit-i1547930812-s6569684725.html
@johnmcclain3887
@johnmcclain3887 3 жыл бұрын
Very nicely demonstrated, I believe I will be finding one of those for myself. Thanks much for finding a nice piece of gear.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi John McClain Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@varman001
@varman001 3 жыл бұрын
i have the exact same one, I added an external lipo battery pack plug so it will last a lot longer. great little spot welder.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I did 300 spot welds,, and I got tired before it did :-)
@chocolate_squiggle
@chocolate_squiggle 2 жыл бұрын
That looks perfect for me. I'm not building battery packs, I just want to be able to repair one or two home devices each year (by refreshing the batteries). Til now I've soldered some Ni-MH in a shaver and electric toothbrush but I'm not that proficient and don't want to heat damage 18650's. So this just looks great for occasional use. It works and it stores away easily.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi chocolate squiggle Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@colins2
@colins2 Жыл бұрын
That's exactly what I want to do 🙂
@bryzabone
@bryzabone 3 жыл бұрын
Used your link, and just bought one 😃 good enough for what I’ll need it for, and I can easily replace those leads if needed. The auto-discharge feature sold me on it. 😎
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Thank You,, I can see that it is very popular! :-)
@crossbladecz
@crossbladecz 3 жыл бұрын
Did same and purchased one locally. I had to open it and screw the battery on the main board but otherwise all good :)
@freelectron2029
@freelectron2029 2 жыл бұрын
auto discharge is a pain in the ass. prevent you from getting good pressure down before it fires. especially with thicker gauge nickel strip for high power applications.
@partasuhari
@partasuhari 3 жыл бұрын
I ordered a spot welder from Banggood using your affiliate link. Very useful video and tip to be able to replace cells of Makita tool batteries etc.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi partasuhari Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@JohnLee-bf2ux
@JohnLee-bf2ux 3 жыл бұрын
Thanks for the device review n demo. And you channel seems good. Found it by chance thanks to the algorithm gods.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi John Lee Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@crzldesign231
@crzldesign231 3 жыл бұрын
I grabbed one from your link. Perfect piece of kit for battery connections. Sweet.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi crzl design Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@jamescollins6085
@jamescollins6085 3 жыл бұрын
Amazing how small these have become. Thank goodness for solid state components.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
And on battery, the last one flipped my 230volt 13A fuse 😬
@jamescollins6085
@jamescollins6085 3 жыл бұрын
@@MyPlayHouse Would it be possible to run it on one of the phases of your 3 phase power that was originally intended for the water heater? Surely it won't saturate a 50 amp supply?
@a-aron2276
@a-aron2276 3 жыл бұрын
@@MyPlayHouse I posted a comment about this, I have the same spot welder from bangood, I use a 30amp fuse, and a 'c' breaker in the fuse box for high inrush currents. Those spot welders draw over 15amps at 230v, the lights in my house flicker whenever I do a weld and I have a 60amp supply into the house.
@micheltremblay4774
@micheltremblay4774 3 жыл бұрын
Use binder page reinforcement rings for holes needing repair as extra insulators for the positive terminal of 18650 batteries. Thanks for the review, I was just looking at Bangood little spot welder this morning. Take care.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Michel Tremblay Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@larrycurtis2791
@larrycurtis2791 3 жыл бұрын
Glad I found this video. I made battery packs for my cordless tools. My god I soldered forever. I was like I need a spot welder. Look out world here I come.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Larry Curtis Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@zx8401ztv
@zx8401ztv 3 жыл бұрын
Very nice :-D, controlling the duration of the discharge to make it the same every time. And your probes have to be on the strip before it fires, better control. Clever little box, i bet they took a while to get it optimised. Along with the small area probes, control again.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Compared to everything else I have trued,, this is great 👍
@richardwasserman
@richardwasserman 3 жыл бұрын
I bought this welder after watching your video. I just tried it and was having problems. I could not get a solid bond between the ribbon and the battery or between two pieces of ribbon. Used my Dremel to sharpen both electrodes and Bob's your uncle. Works a treat.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Thank You,, nice to know,, I have used 0.12 & 0.15mm ribbon strips and they work well,, I have heard that 0.2mm can be a problem.
@anticapitalize
@anticapitalize 2 жыл бұрын
Make sure you're not applying too much pressure - you want high resistance through only applying very light pressure for best results. The fact that sharpening the tips worked is pretty good evidence that was the root problem.
@PowerScissor
@PowerScissor 2 жыл бұрын
@@anticapitalize Sharpening might not have been the issue. Copper can oxidize a layer you can't see but effect performance. The sharpening could have just removed / cleaned the oxidation and it wasn't the "sharpness" that actually fixed it.
@SkylerLinux
@SkylerLinux 3 жыл бұрын
I'd totally want a holder kinda like that fancy thing you had been working on, but dang that's really decent.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Skyler Azzuolo Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@alejandrolemmo
@alejandrolemmo 3 жыл бұрын
I bougth a very similar one and found myself having to use the max setting to achieve the best result. The one you have seems to be a nit better. At the end it got the job done and it did not break the bank.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I have also been steeping mine up.
@cesarblanco
@cesarblanco 2 жыл бұрын
Fully agree. I have the same spot welder and works great.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Cesar Blanco Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@MrBilld75
@MrBilld75 3 жыл бұрын
Neat little thing and yeah it only runs about $67 where I live (in Canada). Some of those other $25 ones on Amazon look a bit sketchy. This thing looks nice.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Some of them you need to add your own battery. This one is a complete solution.
@MrBilld75
@MrBilld75 3 жыл бұрын
@@MyPlayHouse Well, that's even better then, I did not know that. For the price, "with" battery?! Good deal I think.
@Eo_Tunun
@Eo_Tunun 3 жыл бұрын
It probably is a one trick pony, but it seems to do its trick rather well! Nice little device, really! At first it seems counter-intuitive that you'd be able to power a spotwelder from such small power sources, but what the spotwelder does is taking the power provided to it over a long time and release it in a millisecond or so. The great advntage of spotwelding is that you don't put a great amount of heat into your parts to achieve the connection after all! So Bob's your uncle, Pocket-Spotwelder Olé! :oD
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Compared to the other two tries,, this was great.
@thomasbjerregaard1080
@thomasbjerregaard1080 8 ай бұрын
You obviously have no understanding of how this work
@giomjava
@giomjava 3 жыл бұрын
this is so cool! Thank youfor sharing the spot welder 👍 really impressive toy
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Gio Mag Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@giomjava
@giomjava 3 жыл бұрын
@@MyPlayHouse 👌👌 also, I don't mean "toy" in a demeaning sense. I'm an electrical engineer and I also call $500k equipment as "toys".
@linmal2242
@linmal2242 3 жыл бұрын
Good review. Well done, for a handy little unit.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Lin Mal Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@jaybee258jb
@jaybee258jb 3 жыл бұрын
Brilliant. Thank you for excellent ideas
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
You are so welcome!
@92taffy
@92taffy 2 жыл бұрын
Watched your video for first time good explanation and witty too cheers
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi John Bees Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@johnbrandolini2915
@johnbrandolini2915 3 жыл бұрын
Morten I just looked at the Banggood page for this device and they have attached an English version pdf file for the instruction manual. They've also got a more expensive version that has replaceable electrodes but doesn't seem to have the same features. I'm an amateur radio operator and in the past I've rebuilt battery packs for my portable xcvrs and they were a bitch to solder. Also a lot of my hand tools use rechargeable batteries and it would be a lot more cost effective to rebuild the packs rather than buy new ones. Rebuilding 3 battery packs would pay for the welder imo so I'm going to place an order. I've bought a lot of things from them before and the only complaint I have with the company is the long lead time. I also noticed they have nickle tape rolls so I'll probably get one of those because I know I'm going to have to practice with it before actually using it. Thank you for an excellent video. John. (N1ABE)
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi John Brandolini Thank You very much! Yes when you order something,, you kind of want it NOW :-) glad you liked the video :-) Thank you for watching! :-)
@johnbrandolini2915
@johnbrandolini2915 3 жыл бұрын
@@MyPlayHouse I was shocked this afternoon to find the package from banggood outside my front door. That's the fastest turnaround yet from them. One of the uses I intend to put it to is rebuilding defunct Black & Decker battery packs for some of the tools I have. Mind you I replaced those tools a while back but I abhor throwing potentially useful items out. I found a source on Ebay that sells the sub c 4/5 nimh cells so I can rebuild the packs for around $15. It was minimally charged when it arrived so I haven't had a chance to test it yet. The defective packs I have will be the guinea pigs for the testing. Thanks again for making me aware of this tool.
@johnbrandolini2915
@johnbrandolini2915 3 жыл бұрын
@@MyPlayHouse Morten, I just wanted to give you an update. I ordered some sub-c NIiMh cells to rebuild the battery packs that power my legacy B&D products. There where some vendors on Ebay that were selling "new" packs but considering this equipment has been discontinued for quite a while I decided to rebuild the packs I had. The new cells came with tabs which made the process easier but I tell you from having to try to solder wires to cells in the past this spot welder is p!sser! One electrode holds the tab in place while the other completed the circuit. And, as you pointed out, setting 2 does the job. Many thanks, guy! You saved me from throwing good equipment out.
@zacheryfunch8127
@zacheryfunch8127 3 ай бұрын
Great video, i came from your Dewalt 18V 15cell Ni-mh video. I have a similar solder machine to yours. Now i know i can fix the pack with what i have . Thank you
@MyPlayHouse
@MyPlayHouse 3 ай бұрын
Thank You,, I see your comment on the Dewalt video right under this (in my view) :-)
@andyb7754
@andyb7754 3 жыл бұрын
Very interesting video. Put heat shrink on the probe handles to insulate them against accidental shorting.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
You do not feel it at all,, but the first few time you worry a bit,, and it does not get hot.
@alleny.c1124
@alleny.c1124 2 жыл бұрын
So if I didn't insulate it, it won't short me?
@ikillzombies9975
@ikillzombies9975 3 жыл бұрын
Thank you for this video i am waiting for mine to charge taking forever haha looking Forward to using it
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
It is a cool little thing.
@ikillzombies9975
@ikillzombies9975 3 жыл бұрын
@@MyPlayHouse it didnt even power on,, so i have just sent it back and will get one
@theophilusthistler5885
@theophilusthistler5885 3 жыл бұрын
You can easily reuse old cells even when welded to a a rail. Side cutters, snip off close as can be to weld point, hamd file the rest down cautiously with machine oil (the hair clipper/sewing machine type), flush with Isopropyl, rescore with a fine pen knife then pre flux and solder with a reliable solder station and wide spade tip.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Sorry, I do not understand what you are going for 😬
@804USAR
@804USAR 2 жыл бұрын
Hey thanks for the video, this taught me how to use the one I just bought! I was nervous since the rods are copper with just a plastic coating on the ends, and I wasn't sure if I was supposed to touch them. Can't wait to try it out now!
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi 804USAR Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@thedave7760
@thedave7760 2 жыл бұрын
Did you use it? is it any good?
@804USAR
@804USAR 2 жыл бұрын
@@thedave7760 I do, and it is! It does occasionally blow a hole through the nickel that came with it, but usually that's because the setting it up too high. I spot welded about 10 cells for a hobby drone pilot, and I've spot welded some cells together for DIY lantern projects. For what it is I am honestly impressed.
@thedave7760
@thedave7760 2 жыл бұрын
@@804USAR Thanks I was worried. I will get some proper nickel strips not plated steel it will probably be better.
@davecoates4827
@davecoates4827 2 жыл бұрын
@@804USAR Thank you for posting this information :) I'm def saving to get one of these now! :D
@daif21
@daif21 3 жыл бұрын
Tx for the video. Was looking do one myself. U just decided to buy it 😂😂
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
As you can see in the start of the video I tried other stuff,,, this tiny little one worked the best.
@andrepost7571
@andrepost7571 Жыл бұрын
I have the same one but I need to repeat the weld several times at the same position to get a proper weld at the highest position. But it gets the job done that way.
@MyPlayHouse
@MyPlayHouse Жыл бұрын
I think I see mine becoming weaker as well.
@TranTek
@TranTek 2 жыл бұрын
After your review and ordered it it works really well. thank you
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Hung Tran Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@TranTek
@TranTek 2 жыл бұрын
@@MyPlayHouse after doing more thicker weld i wouldn’t able to get good weld may be one or two weld i got the one with supercaps version it is very strong
@herman389
@herman389 Жыл бұрын
Gonna get 1 soon. Thanks for ur review .
@MyPlayHouse
@MyPlayHouse Жыл бұрын
No problem 👍
@derwissenskiosk8041
@derwissenskiosk8041 3 жыл бұрын
Thanks for this showcase... $70 Bucks and it works :D
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
It can be found a little cheaper,, $55 is a good prices.
@matthewbennett
@matthewbennett 3 жыл бұрын
Just wanted to say I bought one of these from Amazon for around $67 and it is great! I was certain it would be garbage compared to the $20 ones, but this one seems totally great. Edit: the USB charging port fell off the main board. I can still charge the battery by taking the whole thing apart... Micro USB ports are surface mount and don't have through hole supports.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I was also positively surprised, of just how well this was working.
@bkay042
@bkay042 3 жыл бұрын
bought the same one for $67 a few days ago. first one was DOA, power button didn't do anything. Received a replacement 2 days later and it works like a dream. Hopefully I can wrap my brain around the limitations of 0.1 nickel in my projects since I've read this doesn't do well with anything thicker.
@perochristiansen8406
@perochristiansen8406 2 жыл бұрын
Very nice video. I have usein it. Do you shure it is not battery, but condensers 20000Farrad?
@DIYwithBatteries
@DIYwithBatteries 3 жыл бұрын
Wow it looks pretty cool bro.....! 😃👍 I need it so badly. 😂
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I recommend it,, it worked well 🤔
@yeroca
@yeroca 2 жыл бұрын
Spot welders need a bit of resistance between the two metals to work well. If you wrap the fuse wire around the copper, you make the connection too good, and so the highest resistance point is somewhere else, for example between the probe tip and the fuse wire, resulting in most of the heat being produced at that junction instead. I think trying to spot weld the fuse wire to the copper wire is a bit tricky because to get a high enough resistance, you need to have it touch without wrapping, since both conductors are essentially cylinders. You might try putting one short section of the copper wire on an anvil, and hit it with a hammer to flatten it out a little. That will give you a "line contact" instead of a single point contact.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi yeroca Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@a-aron2276
@a-aron2276 3 жыл бұрын
That second spot welder the banggood one, what you need is a 30amp fuse in the plug and back of the machine and depending on what circuit you are using, i had to swap out the circuit breaker for a 32amp C breaker for high inrush currents.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Yes,, way more then what I need,, this small battery one does the job.
@a-aron2276
@a-aron2276 3 жыл бұрын
@@MyPlayHouse yea I don't blame you, to be honest the battery spot welder looks better.
@rizen3467
@rizen3467 3 жыл бұрын
Gonna have to buy this soon so i can weld my own rc packs 👍 nice review!
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi 『 ЯiΖΞΝ 』 Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@johncoops6897
@johncoops6897 3 жыл бұрын
You cannot make RC packs from 18650's. There isn't enough current unless you buy special 30A cells which are expensive. Those ones are only about 2000mAh so that's 15C. For RC you usually need a lot more power than that.- you are better using LiPo pouch cells,
@rizen3467
@rizen3467 3 жыл бұрын
@@johncoops6897 yes, the c rating is lower than with standart lipos but 18650 battery packs are mostly used for long range flights or flights with long endurance. since most smaller efficient rc planes only consume about 10 - 15 amps on full power a 18650 pack is enough to fly
@phxgen
@phxgen 3 жыл бұрын
Li-ion cells also come in sizes other than 18650, there are 3-4Ah 2*700 cells that'll run cool at up to 35A (Sanyo NCR2070c, Samsung 30T, Molicel P42A, I've personally tested all, all handle 35A continuous just fine & burst rate probably double that). I've never used them but I know there are much larger cylindrical cells capable of 50+A. Still incomparable to a great lipo pack but can be not too terribly far off, plenty acceptable for lots of ground based RC stuff. There are always li-ion flat cells as well... I think I'm missing why I can't spot weld my own lipo packs (besides the safety issues - I'm a trained electrician & have been repairing mains single/polyphase AC and all sort of DC devices for probably 30 years without any accidents). I also just spotwelded up a new battery pack for one of my UAV groundstations, previously it supported a 5200mAh 2p 18650 pack that'd degraded to ~3900mAh, I realized the battery drawer could be just slightly modified to accept 2x21700 or 20700 cells and a protection circuit now. A set made with Sanyo NCR20700B, apparently the 1mm lesser diameter baby brother of a Tesla NCR21700B (which don't come with the positive terminal attached, to save weight for tesla, the whole line is composed of fantastic cells imo, and another 10Ah pack with a pair of Samsung 50T when I realized I could squeeze in two more mm. I've got two huge sacks of 5200-8000mAh 3s lipos, able to fly a relatively large 4k video & photography drone many hours at a time, all day basically, without ever having to bring two base stations or charge on the go (the oem battery is like $80, I built much better packs for under 25ea) Plus RC predated any Li chemistries.. obviously there're still many uses for a terminal welder.
@elfpimp1
@elfpimp1 3 жыл бұрын
Making me hungry with all his food talk! I love danishes!
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
STOP likking your mouth, while watching me :-)
@oldschool8432
@oldschool8432 3 жыл бұрын
Loving the spot welder oh an your safety slippers haha
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Old School Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@mercedesmarton3768
@mercedesmarton3768 2 жыл бұрын
Thank you so much! I'm trying to make my own custom cookie / polymer clay cutters, but unfortunately aluminum can not be soldered and using rivets is not the best either. So I do will take a look at this. I was wondering if I should make my own, but it would cost just as much in parts as this.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
I did do a video , where I build my own,, it did not work that well :-/ so I got this one,, and it is much better.
@respt46
@respt46 Жыл бұрын
you can solder aluminium with a blow torch and aluminium soldering rods.
@MadMax0318
@MadMax0318 3 жыл бұрын
Nice video and thank you, good review. By the way, how is the spot welder holding up? I'm thinking of getting one.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
It is still doing good! Thank You :-)
@Tjousk
@Tjousk 3 жыл бұрын
Nice. I was amused by the glasses on your light, I guess it needs to see better too.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I see better with glasses and more light 😳 That is my “Work Glasses 👓 “
@brentpolk2431
@brentpolk2431 3 жыл бұрын
Buy some vinyl wrap. I use it to cover EVERYTHING! It's on my canon 80D LCD screen back cover.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Brent Polk Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@lupemcghee9721
@lupemcghee9721 3 жыл бұрын
Awesome review and excellent information I am a subscriber now
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Awesome, thank you!
@LutzSchafer
@LutzSchafer 2 жыл бұрын
Nice review. I'm a bit concerned though that it could not melt copper. Although you may need higher melting electrodes but 600A should melt copper depending on the on time.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Copper is really good at leading both current and heat,, this tiny spot welder,, is to small,, and nikkle strips of about 0,2mm is the upper limit.
@atomicskull6405
@atomicskull6405 3 жыл бұрын
High setting is probably for tin plated copper strip. Copper has lower electrical resistance than nickel but requires more power to spot weld because of this. The reason they use nickel is because it's easier to weld due to the higher electrical resistance.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Atomicskull Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@Jan_Seidel
@Jan_Seidel 3 жыл бұрын
Nice device after inprovements are done :) Improvement #1 make new longer cables with more beef and insultate to the very tip. Improvement #2 a fixture to attach the box to the desk or similar
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Jan Seidel Thank You very much! glad you liked the video :-) Thank you for watching! :-)
3 жыл бұрын
To your point 2) I glued a Velcro pad on the box and on my silicone work pad. Holds perfectly.
@freelectron2029
@freelectron2029 2 жыл бұрын
longer cables mean more resistance, means higher powerloss and current draw from battery and hotter components and shorter life span
@i80386sx
@i80386sx 3 жыл бұрын
I bought a similar spot welder. Mine has a plastic case. We'll find out how good it works on NiCD and 18650 NiMH batteries soon.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi i80386sx Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@drewpaschal9294
@drewpaschal9294 3 жыл бұрын
Eesh. Spot weld the nickel strips but solder the wires. Also, agree, maybe put some shrink wrap around the unit. Some of the rubber type stuff.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
It is just the first 10-20 welds, where you think about touching the metal.
@AngryHybridApe
@AngryHybridApe 3 жыл бұрын
A very thorough review. The manufacturer should be happy with it. Now, do they have these at Harbor Freight?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I do not think this is a mainstream tool, that some one like Harbor Freight would be selling..
@AngryHybridApe
@AngryHybridApe 3 жыл бұрын
@@MyPlayHouse If it lasts longer than a week, Harbor Freight wont have it.
@rhsdat
@rhsdat 3 жыл бұрын
Nice, very interesting video, thank you :-)
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
You are very welcome 🤗
@dcsensui
@dcsensui 2 жыл бұрын
Very good review. Thanks!
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi DC Springwater Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@debbiebebington9803
@debbiebebington9803 Жыл бұрын
well done Sir a real video thanks so much
@MyPlayHouse
@MyPlayHouse Жыл бұрын
Hi Debbie Bebington Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@irekmaster187
@irekmaster187 2 жыл бұрын
the most impressive thing i've ever seen!
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
It’s okay cool 🤗
@thedude8046
@thedude8046 2 жыл бұрын
Thanks for the review
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi The Dude Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@alexeinuville2555
@alexeinuville2555 3 жыл бұрын
Good explanation!!! I'm wondering, will it weld sterling silver..? Could it be used in making jewelry?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
It is pretty inexpensive,, so you might just want to try,
@muehna1
@muehna1 3 жыл бұрын
10:11 Safety Slippers 😆🙏🏻
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Yes,,, Safety Slippers overrule all other safety equipment! it's not as if I am making the rules!:-)
@Magnetik_moto
@Magnetik_moto 2 жыл бұрын
4:55 If you receive a device with manual only in some strange language, scanning it and using Google Translate does a good job. Translated version usually isn't perfect and you still have to guess many things, but at least it's easier than reading in chinese.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Thank You,, I do know that trick :-)
@soeun4917
@soeun4917 3 жыл бұрын
have you tried the 0.15 and 0.2mm sheet thickness of zinc?This device is great for DIY work
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
That is nice to know,, think the stuff I use is 0.12 and 0.15. Thank You!
@jacakjacak
@jacakjacak 2 жыл бұрын
Thank you , very use full video.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi jacakjacak Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@lpjunction
@lpjunction 2 жыл бұрын
For the Chinese manual, open your android phone with 'Google translate', there is any option to point the Camera to the text and it would try to translate it to English. It also works for other languages such Japanese to English or Korean to English or whatever. The translation should contain 1/5 of jokes, but it will leave enough clues for your guessing. The translation will appear in the screen, it is quite handy. For the sharp pointer electrode, it is a hard alloy of copper which contains silicate or something, it is more durable than pure copper as those in the connection wire.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Well I figured out everything from the back of it :-)
@victorcarmelo8606
@victorcarmelo8606 2 жыл бұрын
Nice video, what other use is there for this welder apart from sticking batteries together, can you solder or join other metals together like making fitting for model boats perhaps? Thanks.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Sorry I do not know of other uses.
@Bianchi77
@Bianchi77 2 жыл бұрын
Keep it up, nice video clip, thank you for sharing it :)
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Rixtronix LAB Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@CrazeUK
@CrazeUK 3 жыл бұрын
Hey nice video Glad you did the strip down. Interesting to see. I am really interested in a smal spot welder. I did look at the inverter tyres but I like how small this is. My question is, outside of battery tabs what else can it spot weld or is it good for?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I do not think this one is good for much more then this,, bigger stuff,, you need a lot more power.
@AClarke2007
@AClarke2007 2 жыл бұрын
Tin Robot Toys?
@km4hr
@km4hr 2 жыл бұрын
As your helpful video shows the spot welder quickly and easily creates an adequate mechanical connection with little danger of damaging the battery due to overheating. However the electrical connection may not be as good as soldering. Spot welding creates a tiny contact area compared to soldering. Presumably this would create additional resistance, although perhaps not enough to matter.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi David Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@Cooper3312000
@Cooper3312000 3 жыл бұрын
wow pretty cool stuff.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Yes, finally something that works!
@jmpaq51
@jmpaq51 Жыл бұрын
thanks a lot for the video. What connectors did they use on the welding cables?XT150, AS150?
@MyPlayHouse
@MyPlayHouse Жыл бұрын
Hi JM Paq Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@toonman361
@toonman361 3 жыл бұрын
I LOVED this review. I have been wondering how to do tiny welding and this looks excellent. Since I have never welded, does the weld require the small metal strip included in the box or can two different metals be welded?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I have only been using this for the Nickle strips for batteries,, so I do not know :-/
@wolverinex4243
@wolverinex4243 2 жыл бұрын
Yeah we need to try stainless steel
@GrandadsWorkshop5252
@GrandadsWorkshop5252 9 ай бұрын
@@wolverinex4243hi did you ever try the portable spot welder on stainless steel ?
@miguelvallejo7289
@miguelvallejo7289 3 жыл бұрын
thats a game changer their i like it
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Makes it very easy!
@anthonyquiroz1998
@anthonyquiroz1998 7 ай бұрын
Very well done 👍
@MyPlayHouse
@MyPlayHouse 7 ай бұрын
Thank you! Cheers!
@Bleats_Sinodai
@Bleats_Sinodai Жыл бұрын
I'm tempted to get one for myself when I can afford it!
@MyPlayHouse
@MyPlayHouse Жыл бұрын
Hope it works out.
@TauCu
@TauCu 2 жыл бұрын
I have the same one, it's a little monster for it's weightclass.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Tau Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@dropinmedia01
@dropinmedia01 2 жыл бұрын
I've tried this one after some good KZfaq reviews, but I could only get 0.1 mm pure nickel to stick reasonability well. For some more serious battery packs, this is not enough. I've ordered the KWeld from Germany, and that is some much better. Even on low settings you can weld 0.2 very easy. A bit more expensive, but worth the extra $.
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
I have used 0.12mm and 0.15mm with out any issues, I hear that 0.2mm is the limit for this one.
@4nlimited3dition_4n3d
@4nlimited3dition_4n3d 2 жыл бұрын
Did you get that exact device or some replica?
@Kaiju-Goji
@Kaiju-Goji 4 ай бұрын
amazing i might get one
@MyPlayHouse
@MyPlayHouse 4 ай бұрын
Hi @Kaiju-G Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@curragh2840
@curragh2840 2 жыл бұрын
Safety slippers, I like it.😀
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Safety is a priority!
@AudreyRobinel
@AudreyRobinel 3 жыл бұрын
Saw this product on bangood a few days ago, was wondering if it is any good... I figured i'd take the chance for the price, it is nice to see it reviewed. My only complain here is that the interface is not the best, but again, it is cheap. But i'd like a slighly more expensive version with perhaps a tiny oled screen and a few buttons for more settings...
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
It works really well for what I am doing. I am happy with it,, :-) an OLED display,,No surround sound? :-)
@AudreyRobinel
@AudreyRobinel 3 жыл бұрын
@@MyPlayHouse i meant one of those small monochrome oled displays, as on the TS-100 soldering iron, it is 128*32 pixels; super crisp text, low power consumption, and it costs 1-2$ per lcd (i2c interface) from the usual chinese stores :) It allows to print values on the screen (for the TS100, you can see the celcius (or farenheit) degrees, rather than 4 levels of power), and thus you can have more precise settings, know the settings exactly (here you would print the amperage output, and the pulse duration, for instance... and having those settings may enable you to succeed the spot welding on copper) Anyway, cheers!
@kmed3526
@kmed3526 3 жыл бұрын
Think this would work for jewelry and chainmaille jump rings? Typically copper or silver, 20-16awg?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi k med Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@digitalsparky
@digitalsparky 3 жыл бұрын
Oh man, pun opportunity missed ... it's shockingly good... :P.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Yes,, missed opportunity right there,, 🤐 I’ll have to change my batteries so I can hit the spot next time 🙄
@dickfitswell3437
@dickfitswell3437 3 жыл бұрын
I'm impressed as well
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
So tiny, and still works good :-)
@stewall101
@stewall101 3 жыл бұрын
What is the max thickness it can weld? What, apart from thin nickel sheet, will it weld? Thanks for the video!
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Rumer will have it that 0,2mm does not stick well..
@jeramboo8511
@jeramboo8511 2 жыл бұрын
Thanks forntjis its nown 33 eu, i needed a cheap but decent one
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Jeramboo Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@zaugitude
@zaugitude 3 жыл бұрын
Maybe make a weighted base for it, would keep it from falling over and prevent scratches, etc..
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi B P Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@jhonepps6061fingers-wild
@jhonepps6061fingers-wild 2 жыл бұрын
Remarkable good vid. Maye
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Jhon Epps Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@OneOfDisease
@OneOfDisease 3 жыл бұрын
how many spot welds do you get in a full charge? what is the max thickness the unit can weld? can you increase the pulse time?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Over 300 welds and that was 0,15mm.
@SlickDiecast
@SlickDiecast 2 жыл бұрын
Great review! Do you think I can weld 2 pieces of 2mm rods together with this welder?
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
No I do not think so,, 0,2mm is about the limmet
3 жыл бұрын
Google glass can come in handy for translations. Well it's the only use case in my situations. 😋
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
There was just enough on the back of the box :-)
@scottl7644
@scottl7644 3 жыл бұрын
Also friends I know it is best to grind off the remains of nickel tabs from reclaimed batteries for soldering but is it as good for spot welding??? Some have said to leave a small amount of nickel on the batteries so that you can weld on to them??? Is this correct or should I grind it all off and start from scratch??? Best regards, Scott. ✌️🙏✌️
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Scott L Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@dieselphiend
@dieselphiend 3 жыл бұрын
Malectrics makes a wonder battery spot welder that's very affordable, and will weld up to .3mm nickel. There's also the slightly better but more expensive Kweld.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
This works great for this low prices.. 300++ weldes on a charge, time for a brake at that point anyway.
@scottl7644
@scottl7644 3 жыл бұрын
Hey friends. Great video. I have the same spot welder but have had problems using anything thicker than 0-1mm. I would really like to know what connections are they using from the pens in to the unit. Are they XT150 bullets as I have bought some pairs and plan to extent the cables to 12inch I’m total using 8awg silicone cable. Am I correct in thinking these things above and will it be of service as I doubt the cable they provide which is said to be 12awg and would I get a better welding experience using 8awg at 12inches or longer??? Thank you kindly friends!!! ✌️🙏✌️
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
I have used 0.12 and 0.15mm and that has worked good.
@scottl7644
@scottl7644 3 жыл бұрын
@@MyPlayHouse Thank you my friend. Keep at it. 💪💪💪🙏✌️🙏
@highducky420
@highducky420 3 жыл бұрын
i also want a spotwelder , because i need to build batterypack's for a electric skateboard sometimes. But have you tried to weld 0.15 PURE nickel with it? or is a regular spotwelder for 230v better for this type of application?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
That is just about the same I am spot welding,,, so that works.
@PhysiqueGeek
@PhysiqueGeek 3 жыл бұрын
Very cool! I've been wanting to start making my own batteries since I got into building electric bikes and this looks PERFECT! How many welds do you get per charge?
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
To be quite honest,, I got tired before it did,, I would estimate at least 3-400 fully charged.
@PhysiqueGeek
@PhysiqueGeek 3 жыл бұрын
@@MyPlayHouse WOW, that's impressive for such a small package. I think I'd have to put longer leads on it but that's simple. Thank you!
3 жыл бұрын
The most I did were 250 in a day and it seemed still to be ready for more.
@PhysiqueGeek
@PhysiqueGeek 3 жыл бұрын
@ heck even if it's "only" 250 per charge that's still great for what it is. Buying an expensive spot welder was the main thing holding me back from learning to do this
@TauCu
@TauCu 2 жыл бұрын
@@PhysiqueGeek just be careful with it as there is a very large and angry _danger pillow_ in it.
@loquitos1972
@loquitos1972 3 жыл бұрын
Did you know that In the BG add there's a link to an English manual? And I would have used heat shrink tubing on the electrodes as I don't like holding copper parts and be a possible electrical conductor myself :D..Cheers!
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
Hi Sanny RC Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@phxgen
@phxgen 3 жыл бұрын
I have one just like this. It rocks tbh. I was wondering wtf about the bare electrodes too, until they arrived and I found that they're covered in nice thick adhesive-type transparent heat shrink tube. It just isn't apparent in pictures or video.
@turbokoni
@turbokoni 2 жыл бұрын
Safety Slippers! Great Joke! But all in all a very informative Video!
@MyPlayHouse
@MyPlayHouse 2 жыл бұрын
Hi Konrad Mayer Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@listerdave1240
@listerdave1240 3 жыл бұрын
I just ordered one. I see there is now a pdf manual in English.
@MyPlayHouse
@MyPlayHouse 3 жыл бұрын
uhh that is an improvement :-)
New Spotwelder - Most powerful yet?
20:07
Stevenc22
Рет қаралды 24 М.
Василиса наняла личного массажиста 😂 #shorts
00:22
Денис Кукояка
Рет қаралды 5 МЛН
1🥺🎉 #thankyou
00:29
はじめしゃちょー(hajime)
Рет қаралды 83 МЛН
Why You Should Always Help Others ❤️
00:40
Alan Chikin Chow
Рет қаралды 107 МЛН
Make a Mini Spot Welding Machine for Lithium Batteries a $0 - DIY
13:54
Gianni Pirola Fai Da Te
Рет қаралды 2,3 МЛН
Repair Attempt - Super Cheap Spot Welder
21:43
Adam Welch
Рет қаралды 190 М.
Build Metal Tank KV-2 | How To Make a Tank out of Metal | Remote-Controlled Tank
15:04
Budget Amazon 18650 Battery Spot Welder by SeeSii Review
14:23
RC Video Reviews
Рет қаралды 111 М.
THERMAL CAMERA Imaging of Soldering Vs Spot-Welding 18650 cells
16:21
EbikeSchool.com
Рет қаралды 134 М.
Cheap Battery Spot Welder 18650, Yes its awesome!
19:58
HowIDidIt
Рет қаралды 216 М.
Cheap 18650 Spot Welder Reliability Mods and Test
11:08
RC Video Reviews
Рет қаралды 149 М.
DIY Battery Spot Welder - Update & Demonstration
23:47
darkkevind
Рет қаралды 766 М.
Spot welder upgrades
15:11
Jeremy Makes Things
Рет қаралды 35 М.
Как работает автопилот на Lixiang L9 Max
0:34
Семен Ефимов
Рет қаралды 14 М.
Mem VPN - в Apple Store
0:30
AndroHack
Рет қаралды 99 М.
Мечта Каждого Геймера
0:59
ЖЕЛЕЗНЫЙ КОРОЛЬ
Рет қаралды 1,3 МЛН
Cadiz smart lock official account unlocks the aesthetics of returning home
0:30