Seriously thank you for this video. Working on a 706 and this answered a lot of questions for me.

Very nice video, very educated person on farm equipment, a skill that will feed your family and enjoy it at the same time. I'm assuming that you are enjoying it because of the lack of four letter words

great stuff, 👍👍

Thanks for posting these, this is the best info on the 414 I've found anywhere on the internet. I have two questions for you: how would you remove the right bull gear if the axle is already broken? Also what kind of gasket material would you use between the hydraulic unit and the differential housing?

Super saar and mahindra distributor repair

Good job

Great vidio

In the previous video you mention you sell parts, used and after market. Would you give more information on that. Old IH parts are getting scarce down in Georgia

Hi Dave Thanks for the video's really helpful please do more. I have a B250 with a whine in the back end going to lift the lid off over the next week or two almost sure it's the pinion and diff. Have you any advice on how to setup or check the correct marrying of the pinion and diff? Any advice on this would be very helpy and much appreciated ps is whining common on the b250 tractors? Regards Andy

Thanks Dave Final questions below if you don't mind it would be really helpful :-) There are only 2 No shims ie located at bull bearing cage? What would cause it to whine now assume wear and needs to be adjusted? Is it now to late as the damage is done and beyond repair? Thanks again for your help

Thanks dave for your reply To be clear gears fully meshed but no tension if it was to be adjusted could you advise how this was to be done? Hoping my whine is a bad bearing assume this could whine also? Andy.

wish I had saw this yesterday before I broke the bull pinion housing trying to take it off without drawing the half shafts and removing the bull gear

Hi Red, I can relate with your work, lol , I recently had timing /hydraulic gear strip on my b414 it is early model with small shaft only gear i could find had larger dia , witch i had to shim with pipe bushing, any info or aid to find a smaller dia gear? Kinda scared of my shim job although it runs could be costly if rips my key job. and thanks for videos .

Hi Dave I have a 454 international I'm trying to clean it up and fix some wiring. So pulled the seat and seat pan off when doing so I found a bolt just sitting in a hole on the lift housing it doesn't fit in there but on further inspection I noticed there are thread's down inside I have no idea what really belongs there it's just in front of the flow control valve and there is a bolt just to the left of it if your sitting on the tractor.looks like there was some kind of retainer in there to but it is missing some of it I was able to get some of it out if you need more info let me know and what ever belongs in there can I buy a new one the local dealer was not able to give me an answer. Thank you

Video on fixing differential lock please

Good day Boy that was interesting. I thought the differential looked awful big for that size of tractor. If you would take a IH M apart would that be bigger. Thanks good video

Hi Dave, Thank for your educated videos. I want to change my 444 pull pinion seal due to leakage into break disk. Only side cover removing is enough to reach the seal ? your video confused me by the way I am ameteur for repairing.?

Dave, your such a smart guy. Video too short . lol.

What I would to know is how you found the lock ring so fast after it shot out? lol! Invaluable information BTW!

Quick question. I’m putting in my new bull pinion seals for the brakes. The new seals are thinner than the old ones. If I drive them all the way in they are loose in the groove all the way out by where the brake disc makes contact. Do you just drive them in part way so they stay tight? Hopefully you know what I mean. Sorry if it’s confusing. Trying to get it re assembled tonight. Thank you.

do I have to pull the axels to do my seals on the bull pinion when doing new brakes only? will the diff stay in place once the diff lock assy is disconnected?

I have a b275 that has gear oil leaking at the shaft that attaches to the brakes. The brakes are coated with oil. How would I go about changing that seal?

Hi CR 424 diesel diff locking shaft leaking. It's coming out from the center shaft (moving shaft at end, not at inner brake plate) Is that a different seal or oring? Do I have to pull inner brake plate out??? Thx mucho!

would you have the procedure to change the diff lock sleeve , both my B414 tractors the sleeves are stripped , so no diff lock on either one

SE ME PASO COMENTARTE ESTOY EN LA CIUDAD DE COSAMALOAPAN VERACRUZ ,MEXICO

Hi Dave i have a 275 and it will only drive on the right hand side wheel when you engage diff lock. It wont drive the left wheel and if you disengage diff lock the wheels dont turn at all when you release the clutch. What could the problem be? Regards Colin

How different is this from the 733 tractor? It seems the IH 733 has a split pin to hold spring of the differential lock?

Got my brakes off and have grease inside the drum. Would that be from a bad brake seal? Looks like I’d have to pull the hydraulic housing and pull the bull pinion shafts to replace if I’m understanding right? Or can the seal be replaced another way?

Can I ask why this vintage International seems identical to the Russian Made Belarus - could they have copied this model the brake system is exactly the same with the ball and disc system. Are you aware of anything like that I happen to have a belarus with crap brakes and your video is very helpful.

can you unstick the differential with out going on the insaid of the transmissin

I believe large brakes? What is the disc diameter for small and large discs in inches?

Do you have the part number for the brake seals for the 414?

Can those hubs be taken out without having to tear apart the whole tractor? I need to replace the brake bull gear oil seals, and I don't want to tear the whole tractor apart to do this.

Hi mate, is it possible to remove the pinion housing without first removing the axles? I've got a couple of snapped bolts on the bottom of RHS housing causing oil to enter brake housing.

HI, good video. Can I remove the LHS differential half-shaft without lifting the hydraulic cover? The shaft broke flush with the outside bearing housing/brake plate. thanks

were could i find 2 bull pinion shaft in canada

hello from finland i have old 414ih and i have problem my tractors differential lock doesnt work at all. mechanism is moving nicely when i push pedal with my leg but lock doesnt engage. can you help me where is the problem and sorry my bad english.

What to do if the diff lock does not release

Hello i no this has nothing to do with your video! but has any one ever put a power steering kit on on a B-275 or any tractors like it would appreciate any info on this thanks in advance

1550 loader lift arm rebuild

It's similar to Mahindra B275

Is it possible to remove the right oil seal of the right brake without removing the upper cover of the differential mechanism and without tightening the large sprocket going to the rear wheel?

I have a 3414 backhoe

Sir my I-H 2504 gas, has locked up on me, after a low rpm 2nd gear fwd start. With bucket load. It let off the screatch of a banshee & never ran again. Engine is locked up tighter then a bull's ass.. Any thoughts? Thanks

HOLA ESPERO ESTES BIEN QUERIA COMENTARTE QUE ESTOY RESTAURANDO UN TRACTOR INTERNATIONAL B 414 , EL CUAL ME GUSTARIA ENVIARTE FOTOS PARA QUE ME DIJERAS SI VOY POR EL CAMINO CORRECTO Y ME PUDIERAS ASESORAR UNAS DUDAS QUE TENGO ....POR TU ATENCION GRACIAS

Czy da się wyjąć prawy simering prawego hamulca bez zdjęcia górnej pokrywy mechanizmu różnicowo i bez dokręcenia dużej zębatki idacej do tylnego koła?