BACK TO BASICS. How To Make A Two Piece OWB Holster.

Рет қаралды 2,982

3 ай бұрын

FIRST, IM SO SORRY THE MIC CUT OUT HALFWAY THROUGH. WHAT A PAIN THIS ORDEAL HAS BEEN!
anyways, i figured id film where we should all start. I non light bearing holster is perfect for the beginner, so this is exactly what you want to practice on. The first coupe holsters you make will make you laugh in the next couple years when you look back.
In this video i show you my tips and tricks that i have discovered over the years on building a basic 2 piece pancake holster.
This particular rig is a left handed owb holster for the glock 19 and alike.
On to the next.
All Material from www.Holstersmit...
and/or www.Knifekits.com
Tell them I sent you!
mold from multimolds
If you would like a holster, visit here👇👇👇
www.Faltacunlim...
If you'd like to email me, email here 👇👇👇
Faltacunlimited@yahoo.com
Follow FalTac Garage here👇👇👇
/ @faltacgarage
ALWAYS RESPECT THE HUSTLE
If you thumbs down this video, i hope you step on a lego hahah
"You'll never be criticized by someone who is doing more than you. You'll always be criticized by someone doing less. Remember That"
~Denzel Washington
"You're going to inspire some people, and piss off the rest. Might as well do it anyway"
~Unkown

Пікірлер: 33

@RockyBurns-m4v 14 күн бұрын

Thank you.

@RockyBurns-m4v 14 күн бұрын

I formed a holster on foam and the top kydex piece rolled down around the top and stuck between bottom kydex and gun. Thank you for teaching.

@FalTacUnlimitedLLC 14 күн бұрын

Pull that top layer tight and you're good!

@searchBLOC941 3 ай бұрын

Dude, your logo as a form of blocking would be killer. And your sawing skills are on point. Lastly, I really dig the voice-over work. Makes me feel like daddy Iggy is tryna whisper us to sleep. 🤣

@FalTacUnlimitedLLC 3 ай бұрын

I was so bummed the mic cut out! It was good content!

@searchBLOC941 3 ай бұрын

@FalTacUnlimitedLLC Hey, you were able to get all of the important points across, and the build turned out killa. Damn mics will always crap out on you. "And it'll embarrass you every time." -Lucky Ned Pepper, True Grit.

@MightyGunzTV 3 ай бұрын

Made a big order from holstersmith & I let them know you sent me! Thanks for the awesome content Iggy!

@stanf9898 3 ай бұрын

This guy makes legacy pieces.

@RockyBurns-m4v 29 күн бұрын

What spacing do you use for eyelets?

@FalTacUnlimitedLLC 29 күн бұрын

100% depends on the belt attachments

@toddpyhtila2138 4 күн бұрын

I HAVE AKYDEX HOLSTER. I RECENTLY PUT A COMPENSATOR ON THE BARREL. NOW THE GUN WONT FIT IN THE HOLSTER. HOW WOULD YOU GO ABOUT OPENING THE END OF THE HOLSTER TO MAKE ROOM FOR THE COMP. HEAT THE KYDEX WHILE SLIDING THE GUN THROUGH IT OR WARM UP THE END OF THE HOLSTER AND USE A WOODEN DOWEL ANY HELP WOULD BE APPRECIATED

@FalTacUnlimitedLLC 4 күн бұрын

I personally cut the end off so it's open and the compensator sticks out. That is probably the fastest and easiest way. You can heat the end up and shove the gun in. But it will look sloppy.

@alfredomenocal1025 Ай бұрын

What laser do you use for engraving?

@rickhighsmith6383 3 ай бұрын

I enjoy watching your videos. What is the grit number on the belt sander? Going to get a belt sander tomorrow and I see that most are supplied with a 120 grit belts.

@FalTacUnlimitedLLC 3 ай бұрын

Ill want to double check but I want to say around 300 grit. It came with 120 and I ordered new belts on amazon to fit it

@rickhighsmith6383 3 ай бұрын

Thanks

@donaldcadwell3911 Ай бұрын

Sorry for my ignorance, but what exactly is "blocking" and why is it used? Was it just layers of the blue tape or was it also the small aluminum piece you put on the sides?

@FalTacUnlimitedLLC Ай бұрын

Blocking creates a channel for the raised components on the firearm to pass freely through the holster without getting caught up. Blocking would be the metal material I put on.

@donaldcadwell3911 Ай бұрын

@@FalTacUnlimitedLLC Thanks for the quick reply.

@glennstar2121 3 ай бұрын

Great video. What polishing wheel do you use?

@FalTacUnlimitedLLC 3 ай бұрын

800 grit sanding disc

@wadejensen6829 3 ай бұрын

What belt loop was that again? Have you or do you ever make magazine holsters using the foam press? I've tried to make a few, and they work maybe 50% of the time. (no vac press atm). I've tried folding from the side and even bottom up.

@FalTacUnlimitedLLC 3 ай бұрын

Those are P style loops and I have made mag carriers on foam. I can do vids on that as well

@kennethwatson6851 3 ай бұрын

I do my mag carriers on foam press and they work 100% every time. I had problems to start with until I added a sight channel to one side.

@wadejensen6829 3 ай бұрын

@@FalTacUnlimitedLLC that would be cool!

@chriswood3924 2 ай бұрын

can I use my actual gun for a one time mold? If so do I treat it with anything to minmize any possible damage?

@FalTacUnlimitedLLC 2 ай бұрын

Absolutely but you have to be mindful. If your gun is Polymer you could crush it. So make sure the magazine is installed and it's a good idea to put 2 layers of tape on each side of the magazine to make sure it doesn't crush. And if you're using metal blocking, it's a good idea to have tape under to protect it