In this video I will walk you through how to install/modify the Alpha-1 handguard to fit AKM style rifles. Remember to show me KZfaq support because it is free and it does help the channel.
Пікірлер: 23
@unit281413 күн бұрын
Correct the WBP kits are AKMs style front ends, it’s funny that they would be called 101s … Russians started the 100 series in the 90s by putting 74 front ends on all calibers.
@jonathanrivera2773Ай бұрын
I had like 4 ak variants I never friggin shaved anything was always solid
@cryowarrior1Ай бұрын
yeah a punch and soft mallet does the trick
@josephledl1384Ай бұрын
Looks great, bummer they didn't keep it clone correct and use flat screws 😂
@DudeManDave3 ай бұрын
Does it add much weight? Been eyeballing this handguard but part of me thinks it might just make it super front heavy
@BERGQUISTARMAMENT3 ай бұрын
It does add a noticeable amount of weight compared to the standard ak furniture. The weight penalty is definitely worth it. Just on the ergonomics alone it’s worth it. But there are more benefits such as a rock solid quad rail to mount accessories and better heat management. I’m currently working on the review.
@KO3A692 ай бұрын
I said the rail is worth it and it doesn't add as much as it seems to the front. 2 I installed mine how zenitco tells you to with a soft blow hammer and pound it into position. I have had 0 problems with it yet. Zenitco says do not use a file to install their rail. In
@BERGQUISTARMAMENT2 ай бұрын
@@KO3A69 The rail had way too much material to just hammer it in. I tried using the hammer at first and I ended up destroying to finish of the rail because I was hitting so hard. You are supposed to hammer it in. But in my case it wasn’t going to fit unless I removed some of the material.
@KO3A692 ай бұрын
@@BERGQUISTARMAMENT The again I am everything but caring of the finish on it. For I never care about resale or looks. Is this soft aluminum since where it's going into literally could act like a file. I took a 2 * 4 put it at the top with a soft blow hammer and then hit it like it was a nail that refused to go into an a oak bored. It is there for good. Does AK are horrendous at this thing called receiver stretch.
@KO3A692 ай бұрын
@@BERGQUISTARMAMENT would share video of what has happened to it in all so you can see.
@deadman123x2 ай бұрын
I filed the hell out of it and it didn’t fit on my WASR-10 😪
@BERGQUISTARMAMENT2 ай бұрын
I wish I could help you out. Try reaching out to the customer service at Barwarus. They might be able to walk you through it.
@2000rayc2 ай бұрын
you are not suppose to file
@2000rayc2 ай бұрын
OMG who told you how to install this?!! everything you did is wrong. you dont file at all. you use a punch and hammer it in. by hitting the handguard retainer. NOT the rail!! go watch the zenitco videos that's how you do it. it should not have gone in that easy for a few taps. you should hammer it in hard
@2000rayc2 ай бұрын
DO NOT WATCH THE KUSA VIDOE ITS WRONG
@BERGQUISTARMAMENT2 ай бұрын
You are correct that you are supposed to hammer it in. That’s what I tried at first. But there was way too much material on the handguard to fit. I actually bent the rail a little bit and destroyed the finish I was hitting it so hard. After realizing it wasn’t going to fit I made the choice to file it down.
@2000rayc2 ай бұрын
@@BERGQUISTARMAMENT you did it just like the zenitco video?
@BERGQUISTARMAMENT2 ай бұрын
@@2000raycNot exactly how they did it but yes. They hammered the rail in by applying force close to the receiver. Very smart I wish I would have seen that before I gave it a go. Different techniques but same results. In the Zenitco video they don’t have to apply much force to make the rail seat into place. That’s how it supposed to be. When I first tried to seat the rail, the lips would barely start to go into the receiver. In the end the lips on the rail sit about 60% into the receiver. I regret not documenting the whole installation process.
@Lil_poopy_Squat2 ай бұрын
I’m about to put this rail on my kr103 kalaahnikov has a video of him installing this exact rail on an ak no filing but the rail was made for kalashnikovs and kusa makes good clones
@BERGQUISTARMAMENT2 ай бұрын
Hopefully the installation process will go smooth. I think you will be happy with the end result.