Bass Tracker Boat Wrap | How To Vinyl Wrap Your Boat!!!

Рет қаралды 48,423

2 жыл бұрын

Today I wrapped my 2021 Bass Tracker 175. I go over each step on how to vinyl wrap a boat and the tools and materials you will need!
(Complete Guide to Vinyl Wrapping your Boat)
Boat: Bass Tracker 175 Pro Team TXW
Wrap Material: 3M IJ180 Cv3 - Printed with Latex HP365
Wrap Laminate: 3M 8418G - High Gloss Laminate (1.5mil)
Tools You'll Need to Wrap:
75% Isopropyl Alcohol - To Clean Boat
Paper Towels
Masking Tape
Application Tool - Felted Squeegee
Olfa Blade - Preferably a Carbon Blade 45 Degree
Torch or Heat Gun - For Install & Post Heating
3M Tape Primer 94 - Pre Wrap
3M Edge Sealer - Post Wrap
Check out Raptor Wrap & Sign at:
raptorwrapandsign.com
IG @ / raptorwrapandsign
Mention: RAPTOR10 from Bent Rod Bassin YT for 10% Off!!!
BECOME A ROD BENDER 🎣 bit.ly/2K5JFVn
INSTAGRAM: / bentrodbassin
#basstracker #boatwrap #howtowrap #teamraptor

Пікірлер: 84

@Venomthegr8 2 жыл бұрын

Finally found the Bob Ross of boat wrapping

@sarahdigby1346 2 жыл бұрын

That looks sooooo good! Now I want to wrap my boat! Great video 👍

@BentRodBassin 2 жыл бұрын

Absolutely!!!

@MartinRodriguez-gx9cs 2 жыл бұрын

Great job, u have me thinking about doing my tracker now.

@BentRodBassin 2 жыл бұрын

It’s a great investment, save my paint a few times already!

@DIDGZONEW 2 жыл бұрын

Great Job! Thanks for sharing!

@chrisaliberti457 Жыл бұрын

Wow that looks awesome!!

@TM-ct1sg Жыл бұрын

I want you to know, I wrapped the top rail of my 190 tracker and followed your video to the T. Thank you, what a great job of explaining you did, perfect! Will be doing sides soon.

@BentRodBassin Жыл бұрын

Nice!!

@sunsetadventures5329 10 ай бұрын

Looks Great. I didn't even think about doing something like this to my tracker. Thanks.

@BentRodBassin 5 ай бұрын

It’s a great paint protector or makes an older tracker look new again 😎

@darrenpritchett1516 2 ай бұрын

Awesome, brother. looks great.

@rougetrader8 Жыл бұрын

Nice work! Thanks for your efforts!

@BentRodBassin Жыл бұрын

Thanks for watching!

@braintrustoutdoors8183 2 жыл бұрын

Man bro you did it! Remember we bought our boats around the same time and we talked about your wrap plans. I dig it! Wish you had pics or a walk-around of the whole completed wrap. I kinda see it in your other vids. Question: Are you gonna paint the console to match? If you are ever near WA I'll airbrush it for you. I did Brian Lattimore's (BLatt) - and sneakers and a few crankbaits for him.

@ladycruiser65 Жыл бұрын

Awesome Job❤

@BASSNGRASS 2 жыл бұрын

Man That looks really good

@BentRodBassin 2 жыл бұрын

Thanks! Came out real nice 👍👍

@pardselmertv 2 жыл бұрын

Wow its very nice design of vinyl wrap.i really like it.may i know where i can buy that?

@ReapeR2129 2 жыл бұрын

NICE!

@BentRodBassin 2 жыл бұрын

Ready to rip some lips!

@vicwalter9918 2 жыл бұрын

Were can I get that wrap

@rudyvaldez4902 2 жыл бұрын

Your pretty good at making these videos you ol blueberry

@Vbokisha Ай бұрын

Will it bond on sanded 2500grit or need to be polished surface. And is foil good aginst algee?

@ovrlndtravel 2 жыл бұрын

Awsome vid 👌🏻! I have 2016 Pro170 that I would like to wrap, Do you sell the wraps and ship them for a do it yourself kind of proyect?

@BentRodBassin 2 жыл бұрын

I don’t, sorry.

@marklopez8378 9 ай бұрын

That's badass bro, would this work on an older aluminum bass tracker? Thanks for the vid

@BentRodBassin 5 ай бұрын

Absolutely!

@r24sanchez Ай бұрын

I have a boat that is a black hull with stickers. How does your wrap work wrapping on top of your existing logos?

@justincooper7497 2 жыл бұрын

Where you popped the pin holes to release the air bubble would you put sealer over them

@BentRodBassin 2 жыл бұрын

No sealer needed, just post heat and your good to go!

@cougar281efs 7 ай бұрын

Looks great Nice video Any problems going over the original decals? Car you see them after the wrap is on?

@BentRodBassin 5 ай бұрын

You can layer over the decals with no issue. They are slightly embossed under the wrap.

@FishingLifeTV225 2 жыл бұрын

Do you do this for a living?

@vitovaldez7470 2 жыл бұрын

Did u have to cut around the hull numbers ? Great video 👍

@BentRodBassin 2 жыл бұрын

Replace with new decals ✌️

@TM-ct1sg 2 жыл бұрын

How do you apply sealer to the edge if you cut the wrap flat without overlapping to the bottom?

@BentRodBassin 2 жыл бұрын

Just wipe it on, vinyl to hull

@Jesse-jc4vv 2 жыл бұрын

Sick shop dude, what dolly do you use to move your boat around inside the shop?

@BentRodBassin 2 жыл бұрын

I just roll it around, it’s not a double axle.

@Jesse-jc4vv 2 жыл бұрын

Thanks

@bobreichel 2 жыл бұрын

is there a difference between car wrap and boat wrap material?

@BentRodBassin 2 жыл бұрын

There are different wrap materials but 3M IJ180Mc-10 was used on this boat, and can be used on vehicles as well. Side note, the gloss laminate is 3M 8518.

@reelchristianfishin7397 2 жыл бұрын

Did you not want to take the Tracker graphic off?

@BentRodBassin 2 жыл бұрын

Kept it on for resale value.

@mikebartolini2918 2 жыл бұрын

I’m looking for a wrap for my bass tracker any recommendation

@BentRodBassin 2 жыл бұрын

Raptor Wrap And Sign in Rogers. 👍

@chadpearsall7398 2 ай бұрын

How is the wrap holding up under the waterline? My black tracker needs paint, but I may try to just gloss wrap it over painting, do you think it will hold up long term?

@BentRodBassin 2 ай бұрын

Still like brand new, I wrap boats professionally.

@scottcozart8950 2 жыл бұрын

I bought a brand new tracker today. can I bring mine to you let you wrap it??

@BentRodBassin 2 жыл бұрын

For sure, check out Raptor Wrap and Sign in Rogers. 🤙🤙

@TM-ct1sg 2 жыл бұрын

Can you put knifless tape to primer and still use the tape to cut?

@BentRodBassin 2 жыл бұрын

Yes it works well on top of primer 94

@TM-ct1sg Жыл бұрын

Is it difficult to remove the plastic casing around the cut tape once it’s put over the primer.

@WONofAkind Жыл бұрын

What different steps for wrapping fiberglass?

@BentRodBassin Жыл бұрын

Same, as long as the gel coat is in good condition. No oxidation or roughness, needs to be slick to stick 🤙

@michaelj8067 2 жыл бұрын

Where did you get the wrap?

@BentRodBassin 2 жыл бұрын

Raptor Wrap and Sign in Rogers, AR.

@richurban659 11 ай бұрын

Hey bud where u get ur wraps from

@BentRodBassin 11 ай бұрын

I design them, and Raptor in Rogers prints them for me.

@robertsimcox8185 6 ай бұрын

How much did the printed wrap cost or did you print it yourself?

@BentRodBassin 5 ай бұрын

Depends on the shop, $8-$10 a sqft normally for 3M-IJ180

@SeeLifeBro 2 жыл бұрын

How much should it cost to have someone print out a wrap like yours to install it yourself? I have the exact same boat but white and your wrap looks super legit. I want it 😆

@BentRodBassin 2 жыл бұрын

Depending on design cost, I’d estimate around $700 👍

@SeeLifeBro 2 жыл бұрын

@@BentRodBassin thanks man super cool!

@scottyablonski1740 Жыл бұрын

@@BentRodBassin what state are you in

@timbrown479 3 ай бұрын

What would something like that cost shipped?

@BentRodBassin 3 ай бұрын

Most places are 100$ per linear foot.

@TM-ct1sg Жыл бұрын

Question: so you just trim to rub rail.

@BentRodBassin Жыл бұрын

Yep!

@BentRodBassin Жыл бұрын

No need to silicone, unless you need too.

@walleye56789 3 ай бұрын

How long does a boat wrap last?

@BentRodBassin 3 ай бұрын

They average 3 years, depending on usage and sun exposure.

@jeremys636 2 жыл бұрын

What would something like this cost?

@BentRodBassin 2 жыл бұрын

Depends on the shop, material and design time.

@eduardomendez3800 Жыл бұрын

greetings friend, how can I buy that for my BASS TRACKERS

@BentRodBassin Жыл бұрын

Come on by an well get you taken care of 🤙

@johnny_jgs2435 2 жыл бұрын

Hi it's same vynil as car wrap?

@BentRodBassin 2 жыл бұрын

Yes, it is.

@johnny_jgs2435 2 жыл бұрын

@@BentRodBassin thanks

@Harlanmote 2 жыл бұрын

Try one with rivets and a rib down the side. It took me 2 hours per side on an 85’ 18’Alumacraft. I didn’t use any seam sealer mines been on for 2 years not a pealed place on it. I cut it 1 inch above the bottom of the boat. Putting on a wrap is not for a beginner. I only used the heat gun on the rivets.

@BentRodBassin 2 жыл бұрын

Rivets are definitely fun, good times!