The replacement battery on Amazon: amzn.to/39ZYA4n Alternative: amzn.to/3TPbM19 (Associate link)

Thank you so much for taking the time to make such a video. You help make some of us family heroes and thereby make the world a better place. For future comment readers: mine also had a few differences with the Flip5 in the video, like what was said in one comment. No screws on the caps , only on the speaker. The power inner connector did not need to be undone, it was glued anyway (one small part came out), the wire was long enough to push the motherboard out enough to get to the battery connector, albeit after lots of coaxing- maybe it had a bit of glue too. While pushing out the motherboard, a flat ribbon connector came undone, probably should not have come out this way, maybe the wrong end of a connector came out. Delicate job to replace. After reassemble it worked great.

This helped me so much I thought something was wrong with my JBL but it was actually dead because of overpowering, I purchased my kit off of Amazon and it came with everything and his directions are straightforward I recommend

1:00 mine did not have any screws, just clips. 3:20 My speaker plug was located under the motherboard. I could have pulled it off but there would have been no way for me to put it back. So I left the speaker dangling. 3:33 the battery plug was facing inwards making it extremely difficult to unplug it. Your battery connector was at the end of the motherboard whereas mine was in the middle. There was one more connector attached to the motherboard that fed to the exterior control buttons also preventing me from pulling out the motherboard. Once I had irreparably damaged the speaker as the bluetooth antenna wires got ripped out of their socket, I discover that the speaker plug wasn't a plug at all. It is permanently connected to the motherboard. Your video was great but I believe JBL saw this and in their next iteration of the Flip 5 they specifically designed it to be more difficult or near impossible to replace the battery yourself. On the inside of the case there was a little sticker that read Flip 5- V3. Thank you JBL. You have joined the ranks of SONY. Another electronics company I will never buy another product from again.

Very well done. Clear and easy to see. Thank you

Very Helpful! Was very easy to follow along. Thank You So Much!!!

Thank you so much mate. Perfect tutorial. It worked for me. Cheers!

Super helpful, thank you!

Without this video I wasn't able to replace my battery, thanks so much...

Very good video! Thank you for making it.

Thank you. Nicely done.

Very nice and neat way Very Good

Thanks for your time

Thank you man! :D

Excellent tutorial . Thank you! Shout out to the Swiss Army knife!

I have 3 flip5s and they are almost a year old .. how to know that when should i replace the battery ? The method you show was very good and i appreciate it. Kindly revert

*For all who struggle because it doesnt work like in the video* TRY THIS - #MegaSafetyFirst maybe you can pin this! As experienced and mentioned by others in the comments there seem to be other (newer?) versions of the JBL Flip 5 - where the inside looks different and you have to work it different than in this video. I repaired mine so I thought it would be cool for you if I made a little instruction: 1. You have to make things different than in this video. So you should not try to force the material to behave like in this video. Otherwise you will break things. 2. The first cable with the white adapter, that is connected to the platine, will go off, if you just gently push it side to side, pull a little, again push side to side and so on. 3. Don't try to remove the speaker (as you experienced it in your attempt). Just pull it out and work around the cables having the speakers hang outside while still connected. 4. Pull off the sticky black foam in the back so you can work there. There is also foam on the platina. I removed a lot of it because it makes it easier to remove the platina afterwards. 5. There are several ribbon cables that connect the platine to the outer body of your JBL Flip 5. Open and disconnect all of them but take a picture to make sure you remember which one has to go back in which place (there are numbers on the ribbon cables that help you to identify them afterwards). Especially one ribbon cable is pretty hard to reach as it lays on the inside. Some ribbon cables can be taken off after pulling the little plastic barrier up. Others (the brown ones) are not working like that. You have to pull them up parallel to the cable. They will come off easy. Then you can pull the ribbon cable off. Sounds complicated but it isnt. 6. Yes, the bluetooth antenna is sensitive. But if you just gently solve it it shouldnt break. You have to be careful there. 7. there is another little cable with a golden knob. It is connected to the outer body of your Flip 5. You can just pull it off. It will be easy to reattach it. 8. At this moment all cables should be removed from the outer box of your Flip 5. If the cables are not removed, dont proceed! 9. The platina is very hard to move. Just pull off some of the black foam thats on the edges (but gently!!). That should make it easier. You really have to push your fingers against it. It will come into your direction. 10. Because you removed all the cables you can pull off the platina far more than in the video. 11. Replace the battery. 12. The rest is not easy but you will get there by yourself. Basically putting the cables back and so on. Kind regards

I have 4 flip 5's 2 charge 5's and a boombox 2 which all link together and sound fantastic. Help video for when I need to replace the battery. I wonder if there is a battery upgrade?

Thanks for clip

looks like JBL changed the internal design a tiny bit in the last two years. From the looks and feels, i would guess to speed up the assembly process of those things. :D nevertheless, it was still easy to take appart, you only have to pay attention to the antenna and ribbon connectors, push out the motherboard a bit to reach the connectors so you can safely disconnect all three of them, otherwise you are screwed if those break... But still nice instructions, especially on how to open that thing. thanks a lot :)

Good

My little flip lock for the ribbon wire flew off, now it may be broke. So where can i find the tiny plastic retainer for the ribbon wire? Thanks. Great video by the way. :)

Great video. I need to do this to my speaker. Can you please tell me exactly what model battery to order? I googled it but there was multiple batteries.

My JBL is also a bit different. I had to remove the main cover, unscrew the speaker itself, remove it and there inside I found a cable that was not plugged in properly. No need to remove the side covers.

Will the 21700 battery fit into the battery compartment?

Have 3 with same issue. No power, only power button lights up when plugged in. Battery gauge does flash. Also installed new battery. Nothing works... Yes I did resets. Any idea? Thanks...

Does resetting the speaker turns off lfm?

my flip 5 just died the other they when I plugged it in to the socket to charge. Is it probably the battery right? Is there a way to tell that the problem is the battery ?

¿Dónde podre comdre comprar la batería?

I found a JBL Flip 5 6800 mAh battery. Can it go instead of 4800 mAh?

The foam pads on the replacement battery are not as wide as in this tutorial or what's on Amazon. The picture on Amazon look like they are the same size, but they are not. The original foam pads do not transfer to the new one (they don't come off the old battery in one piece.) Will the thinner bans make a difference?

Internally, my one year old JBL Flip 5 is different from the one shown in the video. My battery connector is in the middle of the mother board. It is virtually impossible to replace the battery.

dont know how old this flip5 is, but mine is like 5 years old and its totally different. this method doesnt work with recent versions, as thery are constructed differently

Is there anyway you can do a video on water damage to the charging port

I looked this up to check the battery connector on my flip 5 and it was as I expected, the connector wasn’t fully plugged in

No puede ser flip 5 tambien sufre del problema de bateria al igual que flip 4

Is it still water proof after you take it apart?

I have also a jbl flip 5 but yours is aother than mine. I have no screws for replace the cover. Your speaker has black and red cable, i have black, blue and red.

Ho seguito il tutorial, ma non serve smontare tutto : basta staccare il coperchio e la spinetta della batteria dal lato dove è alloggiata e sostituire.

Save yourself the trouble. Newer models have a white (ground wire) that came off the casing, broke one of the ribbon cables because there was no flip connector. Battery costs about $20. Bought a new Walla speaker for $60 with shipping/tax.

Plz help me. I put it on charge and after 2 hours I see that it is not charged and when I open the charging, I see that the charging light goes up and down and the jbl speaker is not on.

I did something wrong. Followed the video exactly, put a new battery in (the straps around it are shorter than the original so it does wobble a tiny bit, then reassembled. But now whenever the volume goes over half, it shuts down for no reason

Once I increase the volume of my flip 5, it trips off immediately, why is it so?

WHY MINE IS SO DIFFERENT?

you skipped some important steps i.e. the bluetooth wire should be removed first

All that just to change a battery, I would rather take it somewhere and get it done

Very bad design

Lol battery is $22. Speaker was $99. If the batt fails within the warranty period ill just exchange it. Afterwards ill just get a new speaker or upgrade. It's not meant to be user serviceable even though clearly it can be done. The second you open it up its no longer IPX7 CERTIFIED. It's like dive watches you can't replace those batteries yourself because they have to be pressurized and tested after they are opened up... more sense to buy a new one if it's outside of warranty

OR, just buy a new one.

Ha easier to buy a new one