Baxi/potterton promax E133 fault

Рет қаралды 22,280

Snapgas

Жыл бұрын

Quick video on how I go about repairing boilers and how I listen to what’s going on

Пікірлер: 37

@user-iy8vq4mj7s 4 ай бұрын

Thank you for being clear with explaining most just go on and don't get to the point ...but you are clear with helping us engineers .

@snapgas9832 4 ай бұрын

Haha cheers, love to chat, what can I say 😂

@Carl-re6zb Жыл бұрын

Nice one brother... Carbonisation of the electrodes and rectification probes is very common. The state of the electrodes gives a good insight into if the burner mix is too high or too low.. Burnt or melted probes can mean too high carbon ratio or heavy coating to little. Correct set up of the gas/air ratio very important to correct operation.

@snapgas9832 Жыл бұрын

Thanks for the info mate this is what comments sections are for

@iqbalnuthoo1566 7 күн бұрын

Thank you, good explanation

@dimitriskatsiaounis1290 Жыл бұрын

Well done mate Good presentation and valuable tip!

@snapgas9832 Жыл бұрын

Thank you mate!

@JoseFigueroa-gv4db 7 ай бұрын

Thanks for uploading! I had same exact symptoms. Allowed me to narrow down cause. I cleaned the probe but issue persisted. Ended up being the contacts on the other end of the cable needed cleaned. Contacts calcified from a prior leak.

@snapgas9832 7 ай бұрын

Lovely!

@plumbingheatingandgas8545 Жыл бұрын

Great work mate keep it coming,

@snapgas9832 Жыл бұрын

Will do mate thank you

@macpatel7810 Жыл бұрын

Some good hints and tips there mate. Appreciate you sharing..

@snapgas9832 Жыл бұрын

No problem hope it helps

@rayc1503 Жыл бұрын

Great stuff pal, I generaly use a file to clean spark and rectification electrodes. Works better then wire wool or sandpaper. 👍

@cynt1111 Жыл бұрын

Cheers, going out to one of these tomorrow.

@snapgas9832 Жыл бұрын

Hope it helps

@craigmcgregor5463 9 ай бұрын

Been missing your videos mate. Hopefully your back soon. Always seems to happen. Engineers go in a different direction or just stop filming. More importantly, hope everything's good with you 🎉

@snapgas9832 8 ай бұрын

Thanks mate, had lots of family issues to resolve Then got married and all sorts haha Cheers for the support craig

@mouradchallal6256 3 ай бұрын

Thanks for video

@garethmccarthy8228 Жыл бұрын

I had E133 yesterday, it turned out to be a split condense pipe leaking onto the flame rectification plastic joint and cutting it out. It was the original grey flexible one, replaced to black hose.

@snapgas9832 Жыл бұрын

Yep that’s common on these too

@cheeky1187 Жыл бұрын

Litrally have the same leaking boiler and have not had heating or hot water since 5 15 on 16th Dec.. should be fixed oin next 24 hours but exactly same issue it's leaking and putting the pilot light out

@nickcannon5592 Жыл бұрын

Nice one

@snapgas9832 Жыл бұрын

No problem mate! Hope it helps

@donpetkov73 8 ай бұрын

I have this E133 after installing a new PCB installed from a E168 caused by installing a new smart meter. Do you cover Romford?

@snapgas9832 8 ай бұрын

I’m really sorry I don’t anymore I’m a bit too far away, Sounds to me like the gas may not be getting to the boiler or needs to be purged Please call a local gas safe engineer to repair or rectify this Thanks for watching

@1966reilly 7 ай бұрын

Guys got a eco compact 30 hot water runs fine but no heating.rads and water symbols shown but no flame when demanding heating.The red and green lights are flashing on receiver cant solve?i have turn the hot water dial 90 degrees twice it fires up with flame symbol then heats up then flame goes out do it a couple of times then i get flashing error 133 flame crossed out and an R top right above error number. i have blaming my receiver and thermostat no connecting does that narrow it down ?its getting cold. regards

@snapgas9832 7 ай бұрын

Please contact a gas safe engineer to solve this issue Thanks