Beginner 3d Plane: Twisted Hobbies Laser Complete Review

Рет қаралды 30,686

10 жыл бұрын

This is a complete walk around, tip, and build review on the Twisted Hobbies 32" Crack Laser LITE.
Recommended hardware:
Motor: E-Flite Park 340
Battery: Thunder Power 2s 480mAh or 3s 350mAh
ESC: HobbyWing 12amp
Servos: Futaba S3114
Receiver: AR4000
Thank you all for watching!
Voro.

Пікірлер: 36

@lookeflite 10 жыл бұрын

Nice!!! Beautiful plane.

@Ahblair4 10 жыл бұрын

I got the red one, beautiful and flies nicely

@rogerkukuczka5466 10 жыл бұрын

One of the Best!

@damied866 10 жыл бұрын

Wondered what you were using for a propeller. Great review. Thanks

@jcansdale 10 жыл бұрын

Very nice review. Could you post it on the Laser thread on RCGroups?

@helidork 10 жыл бұрын

Great review. Have you done one on the crack beaver?

@JohnFHendry 9 жыл бұрын

Great servo advice. I laugh when people say small airplanes don't need accurate servos because they are made of foam. The S3114.s are better performing than the larger 17 gram S3101 servo that has a 5 pole motor I used that had 2 clicks of trim play in the gears where theS3114's have no play at all. An amazing servo and worth the money for such a small 3D plane. But the digital versions would be even better as long as the BEC used could handle the current. Have you ever tried the digital version? These servos are in a class all their own it seems despite using a 3 pole motor. I'd think Futaba would update them at some point to coreless as the little 3D planes that could use it are not going away anytime soon. As usual you get what you pay for and Twisted Hobbies has really come along ways and is producing some supper nice foam to pack your servos in.

@Sam-w9des 7 жыл бұрын

they have two glues I seen which glue do I use and how many tubes of glue to build whole plane like you did?

@MattiaMastroianni 8 жыл бұрын

how does it handle in the wind

@hemixprs 8 жыл бұрын

Hi Voro, what is the best way to get good at 3D?

@domda-turtle1463 10 жыл бұрын

I really want to see you do a review on the e-flite umx yak 54 180, I am torn between the inverza and it. I want one of those because they are the only 3d planes that my local hobby shop stocks.

@mn815048 10 жыл бұрын

I hope I'm not too late, but definitely go with the UMX Yak. The Inverza is a little more advanced in my opinion, and the Yak is extremely easy to fly.

@cmerighe2 7 жыл бұрын

In the video, you say you have a Team Motor 2404 motor on the plane, but you show a picture of a T2402. Which one do you have on the plane? And which motor do you have on the flight review video of this plane? Thanks.

@travislinton7258 Жыл бұрын

Wound you recommend this over the Crack Yack for a beginner 3D (durability ). I have fliwn warbirds and wings for years.

@travislinton7258 Жыл бұрын

What motor would you use that can be found today that would keep it floaty but food still in some wind. Thank you.

@richeiger2320 10 жыл бұрын

Thanks for the great review. I have been flying RC airplanes such as the Parkzone T28, and the Great Planes Electrostik for a bit over a year. I can do basic sport maneuvers. A friend got hold of a Laser and brought it out to the field. He let me fly it a bit and I went nuts .... just all giggles for the three minutes I had it. I was looking at TH planes and was thinking of the Yak 55 or this one, but after watching your video, I am going with the Laser. I am totally new to 3D and I think this will be perfect. Plus, you can fly it sport as well. What a great plane. Do you think I should go with the recommended Power Combo from TH (19 gram motor), or should I step up to the 26 gram motor. I will be flying it outside almost exclusively, usually in wind under 7 or 8 mph.

@VoroRC 10 жыл бұрын

If you are flying outside the majority of the time, I'm always a fan of more power. I'd go with the slightly larger motor. Thanks, Voro

@geandy9063 10 жыл бұрын

what is the weight of it ? ( battery not inclued)

@wezsyder1 10 жыл бұрын

Hi there great review, just wondering if twisted hobbies do a slick 360 or 540? Thanks

@VoroRC 10 жыл бұрын

Hello, To my knowledge, they do not make a Slick version, however this Laser flies very similar and I would recommend it above all other Foam 3d airplanes. Thanks, Voro

@RudyNortz 5 жыл бұрын

Twisted Hobbies has bazillion foamy plane models and I have the Crack Yak - is there much difference in the way all these models fly? I can't see much if any difference between the models watching them on You Tube. Just wondering.

@I_am_archie 3 жыл бұрын

I'm about to buy my first twisted... Crack yak. My first 3D.

@GoProHero2Day 10 жыл бұрын

I have never built an rc plane, so I am nervous about buying this, is there adequate instructions and how do I know which motors are safe to use and wont cause nose heaviness?

@VoroxioN 10 жыл бұрын

There is a very nice PDF instruction manual that twisted hobbys puts out. You can find it on the website where you order this particular plane. Also, this plane allows room for error, it'll still fly well even if you do not build it perfect. Thanks, Voro

@GoProHero2Day 10 жыл бұрын

Alright I went back to RC forums and asked. I am about ready to order here in the next day, so just triple checking. Red Laser, power pack option, amazon charger (one they use in example photo on twisted with that dock that charges up to 8 Lipos), amazon DX6i remote control, the little things like glue and tape that were recommended, and 8 2s 450 batteries. Am I good or what am I missing out on?

@VoroRC 10 жыл бұрын

Looks great! I would buy 2x tubes of Welders glue for building, about 4-5x props (Size is 8x4.3 Slow Fly). Double check the charger to make sure it's a whole charging unit and not just the adapter board. You're also going to need a receiver for the plane, I'd recommend an AR400. Finally, I'd recommend purchasing the DX6i off of horizon hobby (fantastic hobby company), that way you can receive the warranty. www.horizonhobby.com/products/dx6i-dsmx-6-channel-transmitter-only-mode-2-SPMR6610 I hope the plane works out for you, it's a great plane to build and fly. Take your time building it and have fun. Voro.

@GoProHero2Day 10 жыл бұрын

I went ahead and purchased my order from TH, came out to $320. I got the AR400 and 2 tubes of welders, and a bottle of CA. For props I bought the props and I think the power package option comes with some as well. The forums recommend agains the DX6i however, and many say go 8 or go home. They said you can not get full power from the servos with the 6?

@VoroRC 10 жыл бұрын

GoProHero2Day I have never heard of that before. I still recommend the DX6i. Thanks, Voro

@GoProHero2Day 10 жыл бұрын

VoroRC Much appreciated I have purchased the DX6i and am on my way to the top! lol

@rambozo_fpv176 8 жыл бұрын

+GoProHero2Day I know this is an old comment but what I suspect the comment about the 6 not giving the 'full power' from the servos is referring to the ability to increase the throws beyond 100% in the transmitter. Not power, but distance.

@cmerighe2 7 жыл бұрын

Unfortunately, you didn't show us where you mounted the battery.

@bobrosso9147 6 жыл бұрын

7200 feet?? I thought FAA allowed max altitudes of 400 feet?

@yourbestversion3942 5 жыл бұрын

Bob Rosso lol his current location is 7200 feet above see level. It sort of threw me off when I first heard him say that too. Most RC planes (profile foam planes) are flown from 1-20ft high. So if he is at 7200ft then he is flying at 7201-7220ft. So the FAA would come into play at 7600ft in his case lol 😂