Belt Trick! Showing how to remove Crankshaft Bolt Without Using a Special Tools Holder

Рет қаралды 203,616

JasmineFatherGarage4k

2 жыл бұрын

Пікірлер: 126

@rogerlaporte8376 Жыл бұрын

Want to see an even better trick pulls out an impact

@Zaxby722 Жыл бұрын

Lol exactly what I was thinking

@lilesnate Жыл бұрын

right

@BmwMe-uh9sy 11 ай бұрын

impact wont have enough power

@jacobecavalier1499 8 ай бұрын

My 3/4 impact will be so much easier

@ryanpeck9648 5 ай бұрын

As someone who has had the honor of removing these god awful bolts. A half inch impact doesn't have anywhere near enough power to break these bolts. It tool my 300lb friend literally sitting on a breaker bar to get them off.

@user-lr6ks3xn6r 3 ай бұрын

Make the bar where you pull up and use jack to push it up to break it loose

@TYSuggested Жыл бұрын

That belt flexes too much. That's your momentum going down the drain and that is why it's costing you so much effort.

@jamesbubba1331 Жыл бұрын

Honda makes a socket 19mm it's weighted for impact use that's a nice trick though I'll remember that thanks

@thesniperofcs Жыл бұрын

I usually stick a screwdriver on the flywheel to jam the crankshaft then i can easily loosen the crank pulley

@YourDoneMate Жыл бұрын

Put a small piece of scaffolding pole or any pole like one off an old trampoline on the end of the breaker bar makes it much easier 😉

@drew8570 Жыл бұрын

Most people know it as a cheater bar

@harryblackburn9556 3 ай бұрын

Now torque it back on using that belt trick.

@friendofvinnie Жыл бұрын

Thank you for your time and patience

@marc-francoisbrideau4797 Жыл бұрын

Of course, the belt just keeps stretching and taking the torque you're giving and only half is going to the bolt. It's called physics

@coltoncubed1167 6 ай бұрын

i used a prybar and lodged it against something to take off and put mine back on, not enough room for an impact the way i did it

@J0hnnyb0y50 10 күн бұрын

If you haven't disconnected the starter, you can use that to remove that bolt. Just tie your breaker bar to the frame to secure it, and bump the starter. Obviously you will have to disable the fuel system to prevent it from spraying fuel everywhere.

@Stroke2Handed Жыл бұрын

Put the breaker bar on the bolt and turn the engine over.

@slimmyhendrix4067 9 ай бұрын

Sounds good and all but the Crankshaft on Honda Accord's spin counter clockwise

@jfGarage4k 5 ай бұрын

Cant start this engine, Its on the engine stand😅

@jfGarage4k 5 ай бұрын

@slimmyhendrix4067 Is right on the Money Honda engine Turn counterclockwise

@Stroke2Handed 5 ай бұрын

@@jfGarage4k I've started dozens of engines on stands. So you can have a good laugh at yourself. 🤡

@frantzloiseau6442 9 ай бұрын

Thus actually helped thanks just left a thumbs up

@bentleynorton6843 Жыл бұрын

Honda uses loctite on crank bolts. Heat them up they come right off

@Bob-he7dl Жыл бұрын

Or just use an impact....

@Jacoby559 Жыл бұрын

You’ll need a powerful impact for that

@carlt6932 Жыл бұрын

That is a good trick to hold the pulley until you torque it.

@stephenjerome7793 Жыл бұрын

An impact works really well for that

@kevinedwards8330 7 ай бұрын

What happens if it spins counterclockwise?🤔

@martinroycroft Жыл бұрын

And in my tool box for later that little trick goes... Genius..

@dougsanders6034 Жыл бұрын

Take a spark plug out and pack the cylinder full of cotton rope and turn the crank manually until the piston locks on it. Leave about a foot of rope sticking out to retrieve it once you break it loose. I hope this helps someone.

@jick747 Жыл бұрын

You could bend the conn rod

@TheRealRonRico317 Жыл бұрын

Can you not use an impact on that?

@joshfixall7938 Жыл бұрын

You need one of those machine gun shaped impacts with the 1" anvil. Good for tractor lug nuts n stuff

@warrenmcelroy4718 Жыл бұрын

A regular 1/2 impact gun with a thick Lisle socket would work just fine, that or a 3/4” drive impact socket.

@stevejackson7899 Жыл бұрын

use a Chinese hot wrench on the bolt head tell it is starting to look somewhat orange, along with your drive belt trick.

@angelgonzalez9490 Ай бұрын

The belt on the outside was not aligned to the bracket you put it, and second belt did it because it was straight and did not twist, therefore the strength go right in to the bolt and you got it

@throckmortonthebrave6634 Жыл бұрын

isnt this interferance or does this have a chain

@jimiliev3924 22 күн бұрын

I wish you viewed your clip before utubing it like show how you wrapped the belt around the pilley

@dougmyers7336 Жыл бұрын

if the engine is still inside the vehicle I use the starter, get your breaker bar setup so when you crankthe engine the bar hits the frame or something solid enough to take the blow.

@jfGarage4k Жыл бұрын

Cant do that on this type of Engine, This Engine turn counter Clockwise. Need to know your Engine before doing this Bump start the starter motor

@dcomputers Жыл бұрын

Sometimes the starter housing breaks.

@Alberthoward3right9up Жыл бұрын

If it turns the other way you just need to position the block of wood in a different spot

@MikeDoesEcom 8 ай бұрын

Can this method mess up the engine at all?

@MikeDoesEcom 8 ай бұрын

Let's say the bolt is still stuck even after cranking engine few times can it hurt the engine to keep trying it?

@bomberman4046 Жыл бұрын

Block the flywheel with a lever like the one for tires, or a strong screwdriver. That's how you do it. And of course, be sure that the thread isn't inverse.

@dgage1776 3 күн бұрын

Block the flywheel with a heavy screwdriver

@harrisonmauldin5090 6 ай бұрын

my Milwaukee impact did the trick just fine

@biff2k2 Жыл бұрын

Run the bar into the ground and turn the engine over if you can.

@chriznew1695 Жыл бұрын

regular 1/2 air impact pop it off easy af

@adamhiggins3786 Жыл бұрын

Lisle 77080 is what you need, it's fantastic for removing these

@CopyrightedCup Жыл бұрын

I just put two flywheel bolts in and wedged a wrench into that.

@jfGarage4k Жыл бұрын

Your right on that but Its kind a shity this may warped the flywheel out do you think.

@CopyrightedCup Жыл бұрын

@@jfGarage4k I have my engine outside the car right now. I am redoing all of the engine seals. And that meant I had to remove the flywheel and clutch. And yes, it could warp your flywheel if you left it in there. but luckily for me mine was already damaged so I ordered a new one from luk for like $30

@dnm1016 Жыл бұрын

Please use an inpact, this puts alot of stress on the crankshaft rolling surfaces....

@IzziedeD Жыл бұрын

crank bolt in my 95 325i fried my dewalt DCF899HB high-torque (1200ft-lb). got the bolt loose, but the poor impact had to be sent in for replacement, guts were seriously wrecked

@notkylelol Жыл бұрын

I use a dcf899 every day working on tractors and implement, I’ve had it three years now. How the hell did you burn it up 😅

@IzziedeD Жыл бұрын

@@notkylelol it wasnt the motor as was still churning, albeit very labored. Somehow the gearbox got messed up. The new one works perfectly though

@notkylelol Жыл бұрын

@@IzziedeD good to hear. I love my dewalt impacts! Idc what any Milwaukee guys say lol I have a 923b that makes life so much easier.

@Deathmetalmechanic Жыл бұрын

Weighted impact sockets on 1/2 impact easy

@robertbarnes9141 Жыл бұрын

Good idea

@tdkyt46 Жыл бұрын

Ratcheting flex heads are not to use in any high break situation like crank bolts.

@classicshelby8931 Жыл бұрын

I use a breaker bar and starter lol just bind the breaker bar and turn the key

@adamcompton567 Жыл бұрын

time to get some 3/4 breakers and rachets

@brianjimenez5616 Жыл бұрын

Honda impact socket??

@38unknownhinson Жыл бұрын

No this application is obviosly inside the car and impossible to use ugga dugga.

@ian9toes Жыл бұрын

Just hit the breaker bar with a hammer, same as using an impact wrench. Don’t even need to secure the pulley.

@notkylelol Жыл бұрын

Had a buddy call me because he had been fighting a crank bolt for two hours. My 1/2” impact took it out in less than two seconds 🤣

@kenxiong6830 Жыл бұрын

Just set the breaker bar to the ground and give engine a crank

@laurelhayes2034 Жыл бұрын

I broke two belts trying this lol

@jfGarage4k Жыл бұрын

Haha wow that ridiculous! I only broke 1 doing this I using the power steering belt at that time

@strol6257 Жыл бұрын

hold the flywheel

@kentjones3757 Жыл бұрын

Use a heat gun on the nut to soften the lock thread on the bolt, don’t use a blow torch just a heat gun

@timwilliams3662 Жыл бұрын

I had to show my son on his Honda, how easy it was to break the bolt loose by putting your breaker bar against the frame, and hitting the key because of the leverage of the fly wheel, will break it loose easier than you can do by hand largest of a long time ago back in 1975

@danielagyei9987 Жыл бұрын

do you please have a video of the how somewhere? I'd love to learn from one. Thank you

@timwilliams3662 Жыл бұрын

You find a stable spot on the motor to get the break of against there and just bump the key over it will break it loose, easiest way in the world to do it

@warrenmcelroy4718 Жыл бұрын

That works, but an impact gun with a thick socket is the easiest way

@riccicrozzie8204 Жыл бұрын

I see a lot of backyard mechanics attended the Butcher's school of mechanical engineering. The easy way is not always the correct way,and,wtf were you using a ratchet ?

@jamesgascoyne.7494 Жыл бұрын

Milwaukee ugga dugga. Max power if its a bad one. Done all types of cars never had one it wouldn't sort. I guess there must be some. But not found it yet. Nor have any of the lads I know in 3 separate garages.

@aslanatlas2876 Жыл бұрын

Bravo unid stat of America

@Kevinmaddox1000 Жыл бұрын

Air impact

@joseprado4627 Жыл бұрын

This guy bought a brand new belt just to loosen up the bolt😂why not an impact gun??

@WilliamSmith-jf5pq Жыл бұрын

So what's the trick you speak of?

@larrybrooks2885 Жыл бұрын

You use to block the bar on the frame and crank the engine over!

@sammymazda 2 ай бұрын

That's a ratchet not a breaker bar

@Alberthoward3right9up Жыл бұрын

Breaker bar a block of wood and then hit the key. If you know you know.

@jamesgallia0147 Жыл бұрын

Use a 1/2 inch drive Milwaukee impact

@danielagyei9987 Жыл бұрын

yes, that works and costs almost $500 with the battery; the charger will top it to about $600

@zerbinauto Жыл бұрын

Impact anyone?

@TheGamersRace Жыл бұрын

Wanna see something crazier? This tool here is called... an impact. I bought this one for 35 dollars. It is as cheap as your belt is.

@marscobras8281 Жыл бұрын

You need vitamin fire next time

@stillnick14 Жыл бұрын

Remove oil pan put a block of wood between crank and block. Done.

@gixxermoon29 Жыл бұрын

"impact"

@tonykb2193 Жыл бұрын

You have the engine out...lock the flywheel.

@everydaylivinglife1753 Жыл бұрын

h22 I made a tool for that

@alexwu8391 Жыл бұрын

this is not how you use a breaker bar

@magagarage7975 Жыл бұрын

Even my broke ass has a impact. The belt absorbs your torque. Bit of rop fed into the #1 spark plug hole on compression stroke can work for you if you're careful.😂👨‍🔧

@TheMaared 10 ай бұрын

1B ft😂

@duskyman1 Жыл бұрын

Too much give..... That's why you need an impact

@luispadilla7519 Жыл бұрын

Mande a fabricar en el torno una herramienta 🔧 de bloqueo de polea y puedo apretar y aflojar sin problemas gracias a dios 💪🇦🇷👍

@donniedye2716 Жыл бұрын

Buy a crank bolt removal socket. They're cheap.

@ridingwithpat Жыл бұрын

That isn't a breaker bar, that's a ratchet and you're crazy. I just put an actual breaker bar on the bolt while it's in the car and flick the starter. Make sure the bar hits the subframe.

@heffedirte6243 Жыл бұрын

Impact

@bengraham9132 Жыл бұрын

The engine was moving, then, you laid it on its side on the floor.

@jimknight2041 Жыл бұрын

That's not a breaker bar dummy that's a 1/2 inch drive ratchet or 3/4 inch drive ratchet.

@KekeeBlack Жыл бұрын

It’s a flex handle breaker bar dude what are you on about

@KekeeBlack Жыл бұрын

Wait… I see it now. He did use a ratchet at one point. Good way to break a ratchet!

@randalceniceros8157 11 ай бұрын

WD 40

@nicolaidavid5319 Жыл бұрын

Cheap mechanic can't even buy impact gun

@rushane1707 Жыл бұрын

I just hate seeing idiots working on Hondas

@daviddawson3366 Жыл бұрын

You were sitting on the ratchet

@JF32304 Жыл бұрын

Might not want to use his name in vain, instead Might want to ask for help and he'll help.

@hw-tq3qb Жыл бұрын

There is no God or gods

@Adam-im4hm Жыл бұрын

@@hw-tq3qb then why use the name of someone that doesn't exist?

@kevinnistor1954 Жыл бұрын

I smelllll a BIBLE THUMMMPPPEEERRRR

@ajauto588 Жыл бұрын

Not really good ticknique,,,

@tatayenlarto6665 Жыл бұрын

I got a better trick 😌 go to Amazon and buy the thick wall suckit and call it a win 🏆 buy right tools 🔧 make a life change

@peterbenson3776 Жыл бұрын

Ruining belts

@zekemowad6501 Жыл бұрын

Why do you feel the need to take gods name in vain ? Very offensive to Christian believers

@aqib2000 Жыл бұрын

Jeeeeeeez us

@Rajgaragesautocares Жыл бұрын

Best way is put socket with bar in crack shaft and start the engine it will loosen easily 😊

@algijura Жыл бұрын

have had one like that in honda even impact gun industrial size couldn’t do it..and my neighbour comes to me with can toilet aerosol can..few seconds sparay ..wait few secs ..spray again. like that 3 times. and when i put impact gun felt like nothing holdig bolt😅😅😅😅😅😂😂😂😂😂