Bernzomatic torch Catastrophe TS8000

No video

Bernzomatic torch Catastrophe TS8000

Рет қаралды 115,156

6 жыл бұрын

This video contains Paid links that gives me a 6% commission if you click and buy any product on that website . Check out my web site www.nobox7.com/ Check out my store front www.amazon.com/shop/nobox7
Support this channel on Patreon www.patreon.com/user?u=3620781 Check out my store front www.amazon.com/shop/nobox7
Support this channel on Patreon www.patreon.com/user?u=3620781 Bernzomatic torch Catastrophe TS8000 Pressure regulator failure something failed after 5 years , however we get it fixed in this video.

Пікірлер: 267

@NOBOX7 5 жыл бұрын

GUYS IF YOU DROP THIS TORCH WHEN ITS LIT IT CAN KILL YOU , THE TANK NECK CRACKS drive.google.com/open?id=11RG-8ujy1UjnBWBDVCMyeHF96bxGes7W

@volvo09 5 жыл бұрын

Thanks for posting that document, great info. I've been refilling my 1lb propane canisters for years and this has got me to go through and retire some of my stock. I've noticed flimsy necks on some of them and now I'm going to trash em. I feel bad for the folks who have been terribly burned or lost their life... if all that liquid propane burst out in a small confined area like soldering in a mechanical closet or bathroom I can easily see death occouring, or TERRIBLE burns resulting in an agonizing death. I wish these bottles were built in a way where cost cutting didn't rule because they are designed to be single use, most people don't like tossing them, and truthfully as this shows some of them are so crappily built that they fail a drop on their factory fill.

@phase1ny 5 жыл бұрын

That was so the neck would crack off and the flame would stop.. Remember, this is a map/pro handle, not pro.

@mariodavila4375 4 жыл бұрын

Thank you .... I'm trying use the oxygen but it release's pressure and gas maybe should find and seal leaks?????

@jonathanolson772 4 жыл бұрын

Does this still occur or have they fixed the issue? Also, do Coleman camping propane tanks that you would normally find at Walmart have the same problem?

@pauldelarouch780 4 жыл бұрын

The Australian owned HOT DEVIL map gas torch is a much better design. Though in saying that , it's produced in China

@labrat810 Жыл бұрын

Start: "This torch lit my hand on fire!" Mid: "I sure hope I can save me 50 bucks" End: 'I basically overclocked my torch'

@craigsmith3645 3 жыл бұрын

Don't remove the sintered brass inserts! They are there as a safety element! They serve 2 purposes, to help regulate the flow & stop liquid propane from going out of the tank, which could cause an explosion of gas. Yeah, removing them will increase the available heat & flame, but it will be wildly unsafe! These things are designed to perform reliably for their intended tasks. Modifying them puts your life at at risk! My guess is that your torch should have been replaced at some point, as you seem to heavily abuse them. You also put the flame too close to the fitting you were heating, and may have caused it to overheat the torch internals. These torches are not designed to be used like that. I hope you have a large first aid kit nearby & 911 on speed dial. Also, you need to learn how to use tools safely and stop showing videos using unsafe practices. Never drill something while holding the work in your hand! Good way to put a hole in your hand.

@liliencalvel6151 Жыл бұрын

Well said. Thank you for that. I thought the same thing; it's time to get a new one. I hope this man never has any serious consequences.

@30roundclip44 Жыл бұрын

My thoughts, you are a lot wrong .

@NOBOX7 10 ай бұрын

All wrong , the brass is there as a dirt filter nothing else guys , get your facts in order . it does not regulate the gas or stop it from coming put as you say . your dead wrong and i am still alive

@easternlcmroofing8751 3 ай бұрын

How did he not?

@spettro9 2 жыл бұрын

Another comment in another video had a letter received from an engineer at Bernzomatic, who said the problem simply comes from leaving the torch attached to the bottle when stored. The seals in the torch are thus constantly subject to the pressure of the gas and deterioration of materials in it. Despite people saying "they've always done that and everything was ok", it does make sense. I take the torch off every time, and I wear big gloves when using these torches.

@spettro9 2 жыл бұрын

I actually bought it and love it. Got steel up to 600+ F anyway. Taking touch off bottle, and capping bottle every time, as I have with basic propane torches as well.

@dhall5634 Жыл бұрын

It's just like the NASA mngt sending the email to the Columbia crew "foam always comes off the external tank and bashes the wing, therefore its fine"

@yaitsme4953 4 жыл бұрын

FYI, this torch has a LIFE TIME WARRANTY. You call them, they give you a return number, you take it back to Lowes and they give you a new torch. Just don't take it apart. If it's leaking gas, that is because the O-rings failed because propane is corrosive to them. This torch will fail, that's why it has a warranty. You don't need your receipt either. My 5 year old torch leaked out the hole too.

@corrupter2311 6 ай бұрын

Frick already removed the brass plug

@mihaiilie8808 3 жыл бұрын

Be safe! I learned a lot and got inspiration from your channel ,to build an oil burner for my small metal foundry. Today i bought this Bernzomatic burner for brazing and on mein says its made in USA ,Wisconsin. Its made in 2019 and has a series and WI under the lock button. Says Chilton Wi.

@777nexus7 5 жыл бұрын

I had problems with the flame on mine. It wasnt normal, after watching this video i gained the confidence to pull my TS8000 apart. I fed a pipe cleaner through the main shaft, i found that an office staple had entered the air intake area. After i removed the staple, everything was perfect and back to normal. I guess things can make their way into the air intake area and cause a blockage of some kind. It made the flame come out all messy. I couldnt believe an office staple got in there and could cause a problem like that. Anyway, thanks for pulling yours apart to teach us its easy enough to dismantle and inpsect/clean

@toolguyslayer1 2 жыл бұрын

That sounds like sabotage buddy

@NightFlight1973 Жыл бұрын

@@toolguyslayer1 Smells like child sabotage... lol. As a 5yr old I remember leaning some nails up either side of my dads bronco tires in the garage. Why? Because it looked cool. Boy he was mad!

@ExDubxC Жыл бұрын

This happened to me a couple hours ago. I've owned this torch for a couple of years now and it was a big surprise. I mostly use map gas through it, was damn glad I had my welding gloves on.

@georgeeaklor3442 6 жыл бұрын

Thanks for the video. I wasn't thinking about how the spark got to flame, thought it was near the bottom of the tube. I've got the turbo torch 504 and was having problems with the igniter and found that the wires coming from the tube wasn't touching the base plate where they connect. played with it a few times and wala, it started working more often than before. BTW, I've got the one that has multi tubes you can put on the body, so I guess they're just designed a little weird and that's why they don't fire every time.

@anotherrant6688 5 жыл бұрын

I actually read a lot of the recall and there are a lot of past and present law suits. The leak in the neck has caused at least two people to drop the unit, ripping the defectively welded neck from the bottle causing severe burns. This company knew about bubbles in the bead around the necks of their bottles and compensated by creating a breakaway groove on the head that would break instead of the neck of the bottle but it doesn't in a fall of less than 6 feet. Instead, the propane cylinder fails at the bead. A man rapped the head against a tree tearing the parent metal of the canister from the neck, igniting the bottle and burning him badly. Some bottle necks were braised instead of being discarded and were offered for sale at stores. There have been fatalities.

@NOBOX7 3 жыл бұрын

yeah that was that guys fault , you dont bang a lit torch against things , he had it comming , i dont think they should be responsible for thta kind of negligents

@shaneintegra 2 жыл бұрын

@@NOBOX7 if your torch kills or disfigures you... Everyone is going to say the exact same thing. "He shouldn't have opened it up and messed with the insides, that's his fault" lol

@juancamaney3562 Жыл бұрын

@@NOBOX7 Great awesome video 👍 Go ahead and barrow a fireman's suit and drill a next step bigger whole on that sintered brass and then light it up, can't wait for your next video 🤣

@labrat810 Жыл бұрын

@@NOBOX7 It's a complicated case when misuse and abuse is greatly exacerbated by manufacturer-known (and ignored) defects.

@totallyfrozen 4 жыл бұрын

For class today, kids, we’re going to watch NOBOX’s shop safety video. LMAO!!! 🤣 👍🏻

@Jmuhung 5 жыл бұрын

just bought a brand new one..and it does exactly that. Thanks for posting..

@anotherrant6688 5 жыл бұрын

Return it. DON'T USE IT. There's a recall.

@Tony-cf8re Жыл бұрын

Blocking the vent with a small screw is defo not the answer its there so the pressure regulator thats in the handle that has atmospheric pressure on one side . if you block it gas will come down the threads and it will come out between tank and torch (it makes you think the tank seal is faulty) once its fixed you can leave the tank on permanently without problem and can easily be fixed again ..... here is the Fix:- remove the tank and the seal in the torch . You will find 2 indents (there to stop you fixing it ) Drill 2 holes at the side of them and with a pair of long nosed pointed pliers in the vice located in the 2 holes you've drilled unscrew the internals which is the regulator . You now need to change the "o" rings.. (mine was the small one ) clean up the threads on the body so if you need to do it again and reassemble it . Its the same as Rothenberg who tell you to buy a new one 😞 basically they have used the wrong "o" ring and nowt to do with the tank being perm on

@ARCSTREAMS 4 жыл бұрын

have you had any leak issues keeping it attached to the tank for every day use or less frequent use cause i heard some ppl leave it for a year and find it has leaked all the gas out maybe cause the rig seal dried up ,would this seal be in the torch body or the tank itself?

@ARCSTREAMS 4 жыл бұрын

after your fix does it work inverted?

@mikeobryan8368 4 жыл бұрын

So I fixed this problem the right way if anyone is interested. The problem lies in the part on the bottom you can't unscrew cause it's pressed against the threads like this gentleman pointed out. Just take a 1/16" drill bit and drill about 4 shallow holes in those pressed in tabs to relieve the tension on the threads, do it right next to the threads. Then take a punch that fits snug in that little hole that's used to screw the piece in and use a hammer to unscrew it. It will be tight at first but I got mine out without any thread damage. When you get it out you will see it has an oring, then there is another piece further in with two orings. One or all of the orings are your problem. Inspect them for damage and replace if needed. If they're like mine and undamaged, just take them off, clean everything and lube the orings up with petroleum jelly and put them back on. Put it back together and test it out.

@NOBOX7 4 жыл бұрын

Right on brother

@mikeobryan8368 4 жыл бұрын

@@NOBOX7 best torch on the market, I couldn't toss it in the trash.

@justina208 3 жыл бұрын

might wanna use silicone instead of petroleum jelly on o-rings, assuming they are rubber

@robertkline5808 3 жыл бұрын

Actually the problem usually is at the bottom the little tit that goes in the propane bottle is damaged and is not sealing correctly

@robertkline5808 3 жыл бұрын

Just take a lil sand paper and smooth it out

@cheath8705 3 жыл бұрын

I own a TS7000 for many years and it never let me down. Problem started cropping up when I used a hose to hook to 30 gal propane tank. I think the oil plasticizer got in. I managed to flush it a bit and it seem to work but never the same. Holding it upside down and getting liquid propane in does not hurt it. At least never in mine. I am still using it. Just hoping it doesn't go out.

@pingpong9656 2 жыл бұрын

I'm thinking the idea of the hole is to ensure propane can escape the handle area - if you get liquid propane in the handle it now has nowhere to go and will explode. Also, I hope the bit you drilled out was not a fire arrestor... you definitely don't want the flame to go into the tank when it gets low... don't get me wrong - I love your video, but always good to be safe too!

@johnw1883 2 жыл бұрын

I have the same design torch, different brand "sure fire T111" Same issue started gushing out the weep hole on the neck. I have always left the bottle connected, never an issue in the 25 years I've had it. Keep it in the tool box on my truck in the garage all year. It emptied entire bottle of mapp gas. Luckily no ignition source when it filled a confined space. I don't recommend altering the torch at all given the explosive rick factor. Also plugging the weep hole only makes the gas escape around the red start button and the hold button and the rube where the ignition wire is housed.

@heavyhauler213 Жыл бұрын

Ya I was lightning a cigarette in my mouth when I found the little hole decided TO LIGHT MY ENTIRE FACE ON FIRE AND MELTED MY BEARD OFF BLISTERS AND RED SKID . PLASTIC MELTED BLOBS MADE OUT OF HAIR . LOOKED PRETTY STUPID ON ME INDOORS AT WORK .. what the fuk

@heavyhauler213 Жыл бұрын

Oh mine was map gas and the failure was the thread sealant BTW. 4000 model

@fireandcopper 2 жыл бұрын

Apparently if you keep the tank attached to the bottle when not in use it fatigues the gasket/o-ring

@susangott1346 Жыл бұрын

I never thought about that. Thanks for the info. After reading the comments and seeing the video, I know it’s a miracle I haven’t had a dangerous situation arise yet. Now I will prevent that.

@NOBOX7 Жыл бұрын

Nice fish , do you throw them back or eat ? fried fish is gotta be one of the most delishes foods . No i cannot spell

@m3sca1 6 жыл бұрын

Those bottles use a BOM fitting. I think they are referring to the tip on the warning label. I have the same torch. Have always preferred the Bernzomatic...can't buy them anymore from the big hardware store. I think that is a safety release in case the bottle was in a fire. That handle has seen some heat.

@NOBOX7 6 жыл бұрын

this is a great torch even though it failed on me at least i got it fixed , i applaud them for making the frame out of solid steel

@getoutside8202 5 жыл бұрын

I just did a similar plug in my torch. I used two set screws and mashed rubber together between them. Is your torch still working the way you fixed it?

@bobsquires4521 5 жыл бұрын

I taped three of the four vent holes and the small opening which burned you badly and it is working fine now. There must be some obstruction for the gas so it's getting where it needs to get for the while - till I can figure out how to make it run properly without all of the tape. Good nuf.. any suggestions?

@anotherrant6688 5 жыл бұрын

RETURN IT. It's dangerous manufacturer's defect. Recall number 12-117.

@mattalancornelison 4 жыл бұрын

Gloves?

@RedShiftedDollar 3 жыл бұрын

That hole appears to be a weep hole to vent any internal leaks. Plugging the hole without fixing the leaks is asking for a worse safety problem.

@NOBOX7 3 жыл бұрын

Its just a regulator vent , no big deal

@RedShiftedDollar 3 жыл бұрын

@@NOBOX7 yeah, you’re right. It’s crazy they put that right where your fingers go. Also, that sintered brass mesh appears to be a flashback arrester to prevent a flame from propagating back into the tank. I wouldn’t remove that.

@melaniecotterell8263 2 жыл бұрын

I heard a story of a powerhouse flood caused by plugging the weep hole on a hydraulic control valve which caused the valve to shuttle which released an axial seal ring on a turbine shut-off valve on a turbine open for maintenance. Never block weep or vent holes.

@RedShiftedDollar 2 жыл бұрын

@@melaniecotterell8263 So the hydraulically controlled shut off valve experienced pressure fluctuations that caused it to open and close rapidly, resulting in a seal failure? Then the valve was stuck open which would normally allow steam to flow, but since it was down for maintenance, the boilers were cool so water flowed instead? Or was this a hydroelectric turbine?

@gaggiggable 4 жыл бұрын

That looked like back draft pressure that caused that torch to ignite - after watching the video, it kinda looks like improper use - not to take the side of bernzomatic, but being a firefighter for many years, you see some things - you "tinkering" and " altering" it doesnt help your case or the situation - just an outside perspective.....

@NOBOX7 4 жыл бұрын

yeah its my fault the torch spued gas out a hole in the side ? and no this wasnt a backdraft bro , thats a lack of oxygen thing

@philldownes8685 3 жыл бұрын

@@NOBOX7 your problem was the seal between gas bottle and the torch. it was not a problem in the torch itself. its the small brass tit that goes in the bottle did not seal, so you then get gas escaping and instead of going through the brass piece it went up into body and out of the hole.. its designed to do this and yes its stupid , but it has to have that as a fail safe. to me its not a fail safe when it burns like yours did..... normally it would be a extremely small amount of gas, but to me the best thing would be to get another torch and melt some alloy in that hole. or thread it and put a bolt in with some sealer....

@bundy3795 Жыл бұрын

Agree fully, backdraught issue, sticking the torch end into pipe… defiantly operator error

@adambrozek3116 Жыл бұрын

I just got the same problem. Same torch. Working fine for some time. Than suddenly blows gas in the side. And it did it without touching it not an user error.

@jr42a1 3 жыл бұрын

Get a brand new $35 Turbo torch on ebay. They are well worth it. Comes with spark ignitor in the handle and a 6' hose so you don't have to have a bottle hanging in our way

@wadebarnes6720 3 жыл бұрын

I have bought a couple different torches I would like to be able to buy one it would last at least a year all I use it for is lighting my bee smoker and starting the fire in my house and yes sometimes I leave in your car sometimes I'll leave it outside but still as much as you pay for one it ought to last a year if you recommend this one let me know

@randylee249 5 жыл бұрын

I had a different type of torch that did the same thing it was the O-ring in the propane bottle itself I replace the O-ring and it worked fine .

@lprkon72 4 жыл бұрын

The Spud does not control flow rate the regulator as it's called is at the base of the neck, if u pull it off the body you'll see a fitting with about a 1/4 mm hole that controls flow rate the piece u took out with the channel locks is the regulator what you drilled is a filter to keep the regulator from getting clogged. Inadition that piece of brass in that bottom spit is the burn back arrestor that's what will keep the flame from reaching the bottle

@ARCSTREAMS 4 жыл бұрын

did you get both cinters out or only one?

@aznseeker 4 жыл бұрын

Replace with warranty. And leak??

@lenueltyson8307 4 жыл бұрын

My torch is not a benzomatic I think it's a Brazzer just different build it catches flame at the tip of the torch where my air vents are and it is not cool if you know anything please help

@TheJACKCOLORADO 3 жыл бұрын

Oh, yeah. I'm down with the $50 screw. Doing that right now. Thanks again.

@contessa.adella 2 жыл бұрын

Hmmm, my Rothenberger Superfire 2 looks to be the identical build to this torch. Ok…so in future, spit on your finger tip and lightly press over that little hole….if it’s leaking you’ll see bubbles forming. Other than that, secure a length of brass tube into that little hole….that means gas can still vent if it needs to, but away from your fingers. Of course gas should not be venting period, right! My takeaway is this: Don’t store with bottle attached. Don’t drop the unit or chuck heavy things upon it. Visually examine the bottle seal periodically. Don’t tilt it over too much in use…like maybe no more than 45deg. If any part is not working correctly….bin the torch cos it’s better than plastic surgery.

@vinny420smokerofdank3 3 жыл бұрын

Thanks to this guy i fixed my TS8000! You're a brilliant dude my dude!

@horatiuimbuzan1452 2 жыл бұрын

En la parte inferior en la unión de la bombona con el soplete debajo de la goma de 3/4 la piesa que ves de latón se desenrosca con Oña llave especial y hay que pasar con la fresa en dos citios donde se ve el latón golpeado así se desenrosca todo el mecanismo

@lilodog8107 2 жыл бұрын

It's "fixed", but would you use it if you were working off a ladder or an experimental liquid fuel burner? Will it be a "$50" screw or a $50,000 hospital bill?

@kaloosh2639 2 жыл бұрын

Im still trying to find a torch tip that I can actually use on mapgas ,a manual torch tip so to avoid these "button start"torch nozzles ,anyone know?ive bought some but they always give out ,because they can only supposed be used for the blue propane torches only,trying to find a manual flint start nozzle for MAP

@NOBOX7 2 жыл бұрын

turbo torch

@heliski989 6 жыл бұрын

Do you think that is a safety precaution so that the torch doesn't explode in your hand?

@NOBOX7 6 жыл бұрын

turns out its a vent for the pressure regulator

@MattJonesYT 4 жыл бұрын

The precaution is to not use that torch!

@sonet1231 3 жыл бұрын

I had VZ gas out the little hole also. Don’t know why , I brought a new one, but been meaning to call the company

@lorakaelber8067 2 жыл бұрын

Can you please tell me if a popping sound and blue flame coming out the holes in the brass neck when you turn it off, is normal?

@NOBOX7 2 жыл бұрын

no you may have something stuck n the nozzle maybe a bug

@davidleslie949 Жыл бұрын

I love the video. I found it very informative and entertaining at the same time. However, you've probably already figured out why your torch caught on fire? It was simply because you turned the propane bottle on its side which then caused pure liquid propane to come out of the torch evacuation escape hole at the bottom of your torch handle rather than trying to escape at the top of the torch, which might not end up well? Typically the liquid propane wouldn't ignite but I think you had a lot going on with your experiment & Murphy's Law took hold. Propane has a boiling point of -40°. Once it reaches anything warmer (Atmosphere) it immediately boils and therefore easily ignited by a flame unintentionally nearby. Take care and stay safe please!

@brandocommando36 3 ай бұрын

This happened to me with the newer model as well, luckly i didnt panic and just blew it out and u screwed , only slight BBQ of bare hand lol but left me a bit pissed that this hole is supposedly a safty feature 🙄 it has been ok last few bottles but recently acting up again . If you have one of these listen for leaks as you hook torch to bottle !

@christopherguy1217 5 жыл бұрын

The brass mesh can get clogged and the pressure has to find a way out.

@solarsynapse 2 жыл бұрын

Don't those have a lifetime warranty?

@shagara65 Жыл бұрын

Lucky you still have your hand!

@leeisawesome123 4 жыл бұрын

I have the rothenberger superfire 2 and it looks pretty similar. Are there any known cases with them failing?

@muppit666 3 жыл бұрын

My superfire 2 literally went today. Only just 2 years old. Rothenberger didn’t want to know. Just told me it’s now trash. No fix. 🤬👊🤘😎

@8dns8 3 жыл бұрын

Mine got the same problem after two weeks.

@simonharper4199 2 жыл бұрын

my superfire 2 leaked thru the hole today (only 14months old) Got 5 years from my last one (same fault) Rothenberger arent interested

@leovela3044 Жыл бұрын

THANY YOU FOR SHARING THIS MAN, BUT IF YOU PLAY WITH FIRE 🔥, GUESS WHAT? SO PROCEDE WITH CAUTION, I ALWAYS WEAR PPE AND I RIDE WITH MY HELMET, SHALOM FROM THE BLUEGRASS

@flashcraft 7 ай бұрын

" a secret feature." Ha!, I love it.

@vetalvet3817 5 ай бұрын

I drilled 2 holes, 4 mm deep, and inserted snap ring pliers, and with difficulty unscrewed them... replaced 1 ring and everything was ok!!!!

@susangott1346 Жыл бұрын

I don’t know if this means anything. I just recently bought a new one. That small hole is plugged in mine with a small rubber plug.

@NOBOX7 Жыл бұрын

Yep thank my videos for that

@victoriam586 4 жыл бұрын

You had no idea what it was, what was on the inner bit of it, and you just.. plugged it with cement and plunged in a screw. You're lucky you still have fingers. In case you're wondering, the hole's a pressure regulator - it keeps it running smoothly when holding it sideways and such. You should've tried cleaning the internals before plugging it, since dirt's your likely culprit there.. cleaning your torch once in a while isn't just a cosmetic thing :I About the ignition-testing, by the way, you can just unscrew the tip and watch the igniter to verify it without having to flood your workspace with stink. I'd guess you probably just didn't have good contact for it on first reassembly.

@NOBOX7 4 жыл бұрын

it worked so long as not upside down , and no it cant blow off your fingers

@victoriam586 4 жыл бұрын

@@NOBOX7 Dropping it while it's lit can kill you, in your own words. Potentially compromising the head's integrity isn't much better. I get it, you're a professional, you have experience with this stuff and feel you know better than some random bitch on the Internet. Could even be true, but don't forget how many seasoned workshop veterans get injured by complacency and "knowing what they're doing". As long as you're human you're still at risk, please don't let yourself get hurt.

@keithnoneya6730 10 ай бұрын

Wow, dude your like so unsafe it's crazy. But I loved the video, it was very entertaining and informative. I thought for so you were going to run that drill through you hand. 🤣🤣🤣

@maxinpains6937 3 жыл бұрын

Cha-Ching ! You got millions !!! Sue them ! LMAO 🤣👌

@braxtonravndal8768 2 жыл бұрын

that weep hole "starting your hand on fire" probably saved your life

@NOBOX7 2 жыл бұрын

Only an idiot would say that but ok bra

@heavyhauler213 Жыл бұрын

No you're the idiot that 100 % correct . Don't talk shit stupid

@larryphillips4164 2 жыл бұрын

HELL YEAH BROTHER WE GOT OURSELVES A GODDAMN RIPPER NOW!!! 😂😂

@HandyTim 3 жыл бұрын

So is the bigger flame mean hotter output?

@tichij9070 Жыл бұрын

Думаю,вряд ли.

@expTRM 5 жыл бұрын

Are you still alive and use the same modified torch? :) Got the same issue with two some years old torches (ts8000 and ts4000), ordered two new, ts8000 and ts4500hs, both of the new torches have the same isse from day zero! I ordered those from US to Europe, so because of shipping costs i can't even bang those torches on bernzomatics head. Is closing the hole a safe fix? Thansk in advance

@overbuiltautomotive1299 4 жыл бұрын

mod repair is option

@ARCSTREAMS 4 жыл бұрын

its cast aluminium body not steel,,also maybe you should not be messing with those cinters ,they might be made for keeping the flame lit when inverted,,they diffuse the lpg from liquid to gas

@muppit666 3 ай бұрын

Had that happen to me with a Rothenberger Surefire 2. Bloody dangerous.

@vodogrey1341 2 жыл бұрын

I have two of these burners with the same problem.

@tichij9070 Жыл бұрын

Доброй ночи. У меня ЯТО 36715,похоже,тоже Китай,уже вторая. Работала более-менее,нормально. После падения перестало щёлкать в ручке при подключении и отсоединения баллона,и плюётся,как верблюд. Кто-нибудь подскажет,как устранить,она новая. Спасибо.

@catalinobracho172 Жыл бұрын

Isso é facil consertar. Tem que trocar 2 o'ring e lubrificar com graxa de silicone. Só tem que fabricar uma chave para desmontar por baixo o maçarico. Na parte de cima não precisa desmontar. É só na parte de baixo.

@veelink6345 Жыл бұрын

This is a real one but amazon and ebay is selling the recalled and fake ones with no labeling on them. What caused this is the little needle valve pin getting stuch open inside the bottle nipple. Same thing happened to me and I burnt the hell out my finger but of course I got mine off amazon and its not a benzo so I cant sue anyone for my suffering. Also I was lighting my fire place inside my house it could have went very badly and I could lost my house if I wasn't as quick to pull off the bottle like I did I could see others just panic and throw it then they have basiclly a live bomb ready to explode at any second

@obfuscated3090 Жыл бұрын

There are far better torch options but these turds still sell for some reason. When I get one in an auction lot of torches I actually want I treat it like the cutting heads on no-name acetylene torches (famous for mixer fires and poor machining) by smashing it then it gets recycled so no one else is at risk. The Turbotorch STK basic torch in your other video is good and the classic Turbotorch with regulator and hose is far more versatile and reliable (and fine to buy used). I collect and rebuilt US-made industrial torches to use and the further one gets away from consumer kit the easier life becomes.

@jamsax6915 Жыл бұрын

Where do you think this is made? I’ll give you one guess.

@NOBOX7 Жыл бұрын

Its a huge country called Corona villa . They also sell organs . Not the musical ones ...

@daveed1797 4 жыл бұрын

The hole where the flames and gas came out, there should be an Allen head screw that holds the lower half of the innards inside the aluminum body

@kleitonmonteiro2690 3 жыл бұрын

3:41 e meio apertado para sair todo o miolo mais sair, depois era so ter feito a substituição dos três anéis orig de borracha que sanava todo o vazamento!

@HavanaWoody 4 жыл бұрын

Damn it! I have had a ts-4000 for 10 years, always with a bottle of map gas. I use it for everything from brazing to lighting charcoal and in the kitchen to peel peaches peppers and tomatoes . The only issue I have had was the upper connection that is held tight by a small set screw. It definitely has taken a few tumbles . I HOPE THE ISSUES ARE WITH THE MODELS AFTER MINE.

@NOBOX7 4 жыл бұрын

Thanks for the input

@Backtheblue-xo8mv 6 жыл бұрын

Same problem

@NOBOX7 6 жыл бұрын

it can be fixed with new O rings

@johnnyzsalt5374 Жыл бұрын

A Bernzomatic has to be the best dab torch ever made. Not sure of they were intending this, but it happened.

@BlondieSL Жыл бұрын

I've only heard of this happening on the cheaper models when they were mistreated. This guy admits that he's dropped it a few times and even the tip that goes into the tank got notched. I have a feeling that this was the main problem. Not a "defect" in the actual torch itself. If there was an actual defect, the news of that would be all over the internet in a huge way. Even up to Government standards. I'm buying one tomorrow.

@imjeffvaderofficial 3 жыл бұрын

DO NOT on Earth remove the "sintered brass" "mesh" stuff. It is used as flame arrestor.

@ruen99 3 жыл бұрын

What about Mars?

@imjeffvaderofficial 3 жыл бұрын

@@ruen99 good question. Since this torch does not supply its own oxygen, and given that, to our current implanted knowledge, there is no oxygen in the atmosphere (if any) on Mars, attempting to use such a torch with the porous brass flame arrestor thing poses no actual danger (if of any use anyway).

@Legozahar1 3 жыл бұрын

Get a turbotorch. Worth the money.

@Wirewelding 4 жыл бұрын

Are ok ?

@owood5243 Жыл бұрын

The reason it didn't spark was because when torn apart the wire connection for the spark either grounding out or the spring wasn't making contact with wire from the striker. Being dirty doesn't matter.

@catcry1857 5 жыл бұрын

That bernzomatic doesn't look like mine. It has a different logo and markings. You know what i mean. Hihi

@totallyfrozen 4 жыл бұрын

🇨🇳 😆

@maxinpains6937 3 жыл бұрын

That's a Chinese knock offs

@alockworkorange7296 3 жыл бұрын

Mine went out once just the ignighter glad it didnt so this but i just took it to home depot and told them i bought it and it died they have lifetime warrenty they replaced it np they dont care they have agreement with all manufactures to be refunded its the same as going thru berbzomatic just faster

@jt-wy8qc 5 жыл бұрын

alot of newer torches have that hole and can do this i pluged the holr and it did not spray out in other places like i was thinking

@randy1203 2 жыл бұрын

It's no wonder there was a blow back of flames. Judging from the beaten damaged appearance of the torch head. You've trashed your equipment. Dicard it and purchase a new one, lesson learned!!!!

@NOBOX7 2 жыл бұрын

I didnt trash any thing but thanks for telling us who you are .

@feger481 2 жыл бұрын

You should have contacted BernzOmatic and sent them the video at the same time. I have no doubt they would have sent you a complete replacement, and probably a whole lot of other stuff.

@NOBOX7 2 жыл бұрын

Actually i called them then was prompted to post when they told me no more warranties

@MrGalactuz 3 жыл бұрын

I had this same problem : (

@pulodogato3888 4 жыл бұрын

Vou fazer isso mesmo com o meu

@RicardoOliveira-iq7ow 4 жыл бұрын

O meu, abri por baixo onde entra o cilindro. Não precisou fazer o que esse açougueiro do vídeo fez.

@77oliveira 4 жыл бұрын

@@RicardoOliveira-iq7ow o Ricardo já desmontei o meu ,...mas não concigui tira a parte de baixo...pra chegar onde tá o vazamento...se puder me dá uma dica agradeço pela atenção dês de já 👍

@RicardoOliveira-iq7ow 4 жыл бұрын

@@77oliveira Manda teu ZAP ou e-mail para que eu possa enviar um vídeo desmontando ele.

@DrWarped 2 жыл бұрын

The hole youi plugged id there for a reason- it is safety! it is like a overflow valve it your tank is not fitted correctly or the threads have obtained damage, a leaking seal etc. it is to relieve any back pressure that can result in you catching fire! You just made a bomb self igniting bomb! P.S. take the tank off after use or you will weaken the seal! BOOM!

@simonlinser8286 Жыл бұрын

Why not throw a wet towel on it and throw it b in a bucket of water or put sand on top of it, or in a bucket full of vinegar and baking soda with a wet towel over the top. Don't try to disconnect the tank if this happens to you. Also does anyone know what the deal is with those valves the little bottles have on them? Is it for refilling?

@30roundclip44 Жыл бұрын

Now i dont recommend this.but if you refiil bottle and put valve on top . ,its in a vertical position. use a small nail or screw and lift up on schrader valve on bottle to vent air to get bottle full.valve can fail and release all fuel inside.which can ignite a large fireball which u will b in side of. All Of this is considered illegal. And Do not vent all air. It should be on a scale.like they do with large tanks.stop when gas starts to come out and weight is comparable to a new bought tank. only do this when u use bottle immediately to lower pressures. It can and will explode. That valve is a pressure relief valve. So don't do it i don't recommend it's illegal to do . But adapter is for sale most anywhere.i just want to explain the dangers of what can happen. 1st degree burns put u in hospital for a month or longer .then twice a week visits adding up to several thousands of dollars for u to pay.most insurance doesn't cover stupid. I know this to b reality. JIM BEAM , JACK DANIEL S, HYDROLIC FLUID, AND A SMALL FLAME.IT RUINS YOUR BUZZ QUICK. IUSED WATER IN A OLD HYD.BUCKET TO PUT A SMALL FIRE ON MY COTTON SOCK. WATER WENT THROUGH SOCK .FLUID STAYED IN SOCK.and burned my leg big time.

@pulodogato3888 4 жыл бұрын

O meu está exatamente assim

@valmoralex2832 4 жыл бұрын

O meu também.

@valmoralex2832 4 жыл бұрын

Não encontro assistência técnica que conserta.

@pulodogato3888 4 жыл бұрын

@@valmoralex2832 consertei o meu Alex Fiz um vídeo

@pulodogato3888 4 жыл бұрын

@@valmoralex2832 coloquei no KZfaq, tubo tocha

@ernandesantos28 4 жыл бұрын

@@@pulodogato3888

@eliassimon7947 3 жыл бұрын

BUY ESAB TURBO TORCH TX500. MINE WORKS FINE IN MANILA

@hawkinscsa 2 жыл бұрын

I have a TS4000 doing the same thing!

@NOBOX7 2 жыл бұрын

the O ring is damaged

@broken1965 6 жыл бұрын

One thing i can add if you drop that bernzo she's toast its a home gamers expensive tourch. For auto start been using chinafrieght for 4yrs at my own risk then the victor stuff/Turbo torch pro stuff for work.. interesting vid thanks for showing diy people people beter off staying away from the cheap stuff and by a decent all brass torch an a Stricker my2c

@NOBOX7 6 жыл бұрын

I agree , and yes i finally figured out that was a vent hole , we could of used you a few months ago , on my store front page i have an all brass torch, its white with brass nobs , tell me what you think about this thing amzn.to/2A5LK40.

@NOBOX7 6 жыл бұрын

Thanks for your input jon

@broken1965 6 жыл бұрын

WORTHINGTON is same same Bernzomatic if you like a autostricker victor makes one for under $100 TurboTorch 0386-0851 STK-99 Torch Swirl, MAP-Pro/LP Gas, Self Lighting

@FrancisR420 4 жыл бұрын

I got the same one for years and it's taken more than a beating

@30roundclip44 Жыл бұрын

There is one more Allen SCREW. Holds spring and igniter..drilling and sealing won't help you AT all..

@anotherrant6688 5 жыл бұрын

This is a defective torch that is highly dangerous. There is a known vulnerability in the neck where the flame is emitting in this video. I would get rid of this thing asap if you value your life. There are known fatalities.

@ampdals Жыл бұрын

Well, this was almost helpful. You edited out the only two parts I needed to see. Not really a complaint, though, since I was just hoping to see to flame lock removal, which isn't really relevant to the topic of the video. Also, I did get enough of a look at it once removed to be sure I know how to get it out without damage.

@LazaroSanchez-zb8rk 3 ай бұрын

For refeo bessott

@lilodog8107 2 жыл бұрын

I think you missed my point. Get rid of broken tools when they get dangerous. By the way, a TS8000 caught fire on me while I was soldering pipe in a house under construction.

@NOBOX7 2 жыл бұрын

Yeah not a good place for a regulator vent , it should be vented to the flame tube then it would just get burned

@jinpark5324 3 жыл бұрын

Something is stuck the propane path so it vent from the small hole - may be carbon buildup.

@jamesringler987 4 жыл бұрын

I did not get much use out of mine before it failed called the company but they did not want to service it or look at it for a redesign other than that I liked the torch.it was not that old though

@superspecialty5169 2 жыл бұрын

Yes, I would like to know who/what f…up? We all want to know, what not to do!

@mpalaskokkalis1476 6 жыл бұрын

Η καλύτερη πατέντα για επισκευή στο φλογιστρο και επισεις όταν ένας ρυθμιστής υψηλής πίεσης προπανίου έχει φίλτρο στην είσοδο του ρεκόρ πρέπει να αφερειται για ασφάλεια και να έιναι ο ρυθμιστής της μπουκάλας με απαιτούμενη ασφάλεια στην είσοδο του ρεκόρ χωρίς φίλτρο για να αποτρεπει τις διαρροές και να δουλεύει σωστά το υγραεριο .

@mpalaskokkalis1476 6 жыл бұрын

Ο ρυθμιστής της μπουκάλας του πετρογκαζ πρέπει να είναι με απαιτούμενη ασφάλεια στην είσοδο του ρακόρ για σιγουριά και ασφάλεια και θα είναι ο ρυθμιστής υψηλής πίεσης ασφαλείας πάντα

@NOBOX7 6 жыл бұрын

Eυχαριστώ για τον φίλο εισροών σας

@mpalaskokkalis1476 6 жыл бұрын

NOBOX7 οκ.