BEST HOSE CLAMP Worm Drive VS Spring Type Hose Clamp

No video

BEST HOSE CLAMP Worm Drive VS Spring Type Hose Clamp

Рет қаралды 2,132

Күн бұрын

Mechanics react to which hose clamp is the best. Worm drive or spring loaded type hose clamps. Check out these fellow mechanics tell us which one they like the best.
Tools on Amazon for spring type home clamp:
Single Hand Pliers Hose Pliers: amzn.to/3QSNqmn
Long Reaching Hose Clamp Pliers: amzn.to/3QRaBO8
Full Kit with both SHORT & LONG Pliers: amzn.to/3WOebfF
Spring Hose Clamp [FITS ON JAPANESE CARS]: amzn.to/4bKnmSm
Worm Drive Hose Clamp: amzn.to/3K7DmlL
BUNDY APPROVED TOOLS AND CHEMICALS:
BEST Dielectric Paste: amzn.to/3KJL053
BEST KIMO 3/8ths Electric Ratchet: amzn.to/3o51OK0
BEST RTV IN THE WORLD (FIPG): amzn.to/3s09hLB
BEST Anti-Seize for Spark Plugs: amzn.to/3KNE9Y9
BEST Mechanic Work gloves: amzn.to/3KTBBYv
BEST Zero Offset Wrenches Metric: amzn.to/3KTAIzs
BEST Metric Wrench SET: amzn.to/3u2NHIZ
BEST Underhood Work Light: amzn.to/3u4EOOW
BEST Headlight Restoration Polish: amzn.to/35w94YY
BEST Synthetic Motor Oil: amzn.to/3u3uM0E
BEST Headlamp Work Light: amzn.to/32ISTqe
BEST Grease for Wheel Bearings: amzn.to/3rQ1ik8
BEST ½inch Electric Impact: amzn.to/3IMa89c
More About BundysGarage:
goo.gl/qv3Wzc
Questions, Comments, Concerns:
bundysgarage@gmail.com
Twitter:
/ bundysgarage
@bundysgarage
On The Web:
www.bundysgarag...
Music by Randall Kent: As seen on NCIS
• Randall Kent - Going H...
All Rights Reserved 2024
© Copyright 2024
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: bundysgarage@gmail.com
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.

Пікірлер: 6

@donaldm9689 3 ай бұрын

Constant spring clamps are the better of the two. Hands down. There's a reason vehicle manufacturers use them even on fuel lines (carbureted vehicles) The material of the fitting under the hose will expand and shrink with temperature. (Radiator inlet/outlet water neck etc.). Spring clamps will slightly expand and contract while keeping constant clamping force. It can not be over tightened and don't need retightening over time like a worm clamp.

@JPN850R 3 ай бұрын

I use worm gear type. As long as you tighten them correctly, you hardly ever need to re-tighten. I've had issues with the spring clamps where they allowed coolant to leak. They must be of the correct size for the application, whereas the worm gear types can be larger in diameter and still work. The biggest advantage of the worm gear clamp is that you do not have to disconnect the pluming to install/remove, whereas the spring clamp requires disconnecting the plumbing. I mainly use products sold at McMaster-Carr, as they carry worm gear clamps with flat surfaces.

@MDC2020 2 ай бұрын

I'll take the worm drive all day. Because if a factory clamp is wore out or broken I can pick a worm drive clamp up any where, They can be removed and tightened by multiple tools, screw driver, nut driver, wrench, vice grips, the list goes on and on, I don't have to remove anything to put them on in most cases and they are very cheap and can be found in any size. That's another thing 1 worm drive can be made to fit multiple sizes easily.

@markbristol2645 12 күн бұрын

The Worm drive can break plastic radiator inlets.

@kirkdarling4120 17 сағат бұрын

Over-torquing any connection will break it. That's a user error. Plumbers use a fixed-torque wrench to tighten worm clamps for permanent plumbing waste uses.