In this video I tackle a mystery engine noise, replace the water pump to fix a coolant leak, and a couple of other quick jobs.
Пікірлер: 30
@fawls6642 Жыл бұрын
As mentioned taking the tensioner off would be a lot easier, its good to see someone cleaning the old bits with a wire wheel before reassembly, you are the first one on KZfaq that I have seen do that so well done to you!
@markxtinkering Жыл бұрын
Thanks Fawls, appreciate your feedback and positive comments. Yes we live and learn, if I ever do this job again...that tensioner is coming off 😁👍
@brousschambers383 ай бұрын
Looks like previous owner stripped the [alloy housing] thread on the original 10mm tensioner retaining bolt then replaced it using a bolt with a 1/2" head. These retaining bolts should be tightened to just 25 NM.
@hunny1968able Жыл бұрын
What a lovely BF, I have a BF2 dedicated LPG wagon as well in New Zealand but I’m in need of a new or reconditioned converter same as yours. I hope to find one soon.
@markxtinkering Жыл бұрын
Hey James, pretty sure you can get a kit to redo your converter? Might be a less expensive way to go. Cheers, Mark
@elijahhemara6520 Жыл бұрын
Yeah bro, you can get kits that fit into your gas converter
@julianalderson393810 ай бұрын
Ive just brought a 2010 bf wagon. Its got few little things to do. These vids so helpful cheers'
@markxtinkering10 ай бұрын
Appreciate the feedback Julian and glad you got some value from the video. Good luck with your project 👍
@simoncross1677 Жыл бұрын
You really know your stuff mate, I have a wagon just like yours on gas,and you've given me some good tips, thanks.
@markxtinkering Жыл бұрын
Thank Simon, the whole purpose of the video was to try help others like yourself. I'm no expert but if someone gets value out of this, then that's my reward. Good luck with your project. Cheers, Mark
@stevanzaharic2 жыл бұрын
Good job everything is done,only you forget to put heather on to hight position for prevention of traped air in system and after that top up coolant.Two hoses on side of engine going in heather module or HIM module which controling heating in vehicle and that is way heating should be put on hight position for sometimes.
@markxtinkering2 жыл бұрын
Thanks for watching Stevan and appreciate your comments. All of those things were done off camera, so rest assured I didn't forget to do it.
@lesliethompson3054 Жыл бұрын
Can cheat and take the tensioner off to change the pulley. The bolt for the coolant bypass pipe is self-tapping, but can still tap a thread if you want.
@markxtinkering Жыл бұрын
Cheers mate, if I ever have to do it all again it will be easier next time.👍👍
@brettpearce6872 жыл бұрын
Pulley bearings n replace water pump asap. I have a BF wagon too
@tepaeaandrews40942 жыл бұрын
Nice.. thank you very much for the video. 👍😎
@markxtinkering2 жыл бұрын
Glad you liked it!
@julianalderson393810 ай бұрын
Nice job dont wana cook it. Over bad seals thermo.
@markxtinkering10 ай бұрын
Yeh glad I did all those jobs, thermostat surprised me a bit. No problems with the ol girl now. Thanks for watching 👍
@andrewlawrance31392 жыл бұрын
Well done very informative
@markxtinkering2 жыл бұрын
Cheers Andrew, glad you enjoyed..
@brettpearce6872 жыл бұрын
Check them all with belt off. Cheap to replace all of them
@fernandomartins9816 Жыл бұрын
Thanks for your help.
@markxtinkering Жыл бұрын
My pleasure Fernando 👍👍
@braidenleeparkes62397 ай бұрын
Rear main seal leak
@markxtinkering7 ай бұрын
Yep your probably right but for now I'm not feeling that enthusiastic 🤣
@jimeddy-oz4gi Жыл бұрын
Was it the tensioner pulley or the idler pulley that was making that marble sound? I have the same noise. Cheers in advance 🙂👍🏼
@markxtinkering Жыл бұрын
It's been a while so can't recall but would change both just to be sure 👍👍
@Bandolero318 Жыл бұрын
Just wondering why the hose from the coolant tank that goes straight over to the top of the radiator is blocked off?
@markxtinkering Жыл бұрын
I can't remember which way around it was...but I either replaced the radiator and the top port for that hose was blocked off...or I replaced the expansion tank and it had 2 ports instead of 1, do blocked it off. Sorry for inexact answer but it was quite a while ago. Cheers, Mark