Why didn’t you check for leaks prior to backfilling
@BidwellCanyonFarm4 жыл бұрын
Great point Michael! I failed to record that part, nor did I mention it in the video. Definitely an important step. Thank you.
@Zaka_sama43932 жыл бұрын
How is that done? If you don't mind me asking, I'm about to replace one and just making sure I'm going in prepared as can be
@BidwellCanyonFarm2 жыл бұрын
Leak check would involve charging the system with water and while everything is closed looking/feeling for drips coming from your plumbing connections, turning on the hydrant and making sure water flows from the hydrant with no problems, turning off the hydrant and making sure water drains from the drain opening before backfilling.
@markpurdin9900 Жыл бұрын
To check is water is draining from hydrant, put your palm on outlet, you should feel suction
@markpurdin9900 Жыл бұрын
If
@christinemartin61102 жыл бұрын
Thanks so much. This 68 year old gal from Maryland appreciates your help. I dug the hole and am letting the plumber do the rest because I have no wrenches. Really like your sense of humor.
@BidwellCanyonFarm2 жыл бұрын
Thanks Christine! I appreciate that. Way to get in there and get dirty. Not a lot of people know how to do that anymore!
@07bigal0810 ай бұрын
helps to make sure the packing nut isn’t frozen before installing … I have two brand new Woodford hydrants that need replaced because the packing can’t be tightened up!
@BidwellCanyonFarm10 ай бұрын
That is a great piece of advice! We had one that needed adjusting and it was already super tight. We just barely were able to get it to stop dripping. Thanks for the comment!!!
@debroberts1296 Жыл бұрын
I love your work ethic and attention to detail. Thanks very much for the video. Now I just need to find my frost line!
@BidwellCanyonFarm Жыл бұрын
Haha, thanks Deb! I wonder if you find what climate zone you are in if it corresponds with frontline. I know up in Montana and colder climates, water lines are set up to 6’ deep. Yikes!
@debroberts1296 Жыл бұрын
@@BidwellCanyonFarm I am in the mountains of California where we get snow. I think it might be 2 feet.
@randykniebes5364 Жыл бұрын
Very well done!!! Excellent directions and procedures
@BidwellCanyonFarm Жыл бұрын
Hey, thanks a lot Randy! I appreciate that!
@melvinmccoy9830 Жыл бұрын
Great job, made it look easy. I Like the tape idea. The support was also a good idea.
@BidwellCanyonFarm Жыл бұрын
Thanks Melvin! I appreciate the kind words. I hope you have a great 2023!
@markpurdin9900 Жыл бұрын
Excellent demonstration
@BidwellCanyonFarm Жыл бұрын
Thank you. I appreciate that!
@cpenland Жыл бұрын
Thanks for the tips!
@BidwellCanyonFarm Жыл бұрын
You betcha! Thanks for watching!
@WoodWorkLIFE3 жыл бұрын
well done, that is way better than the way my yard hydrant is presently installed.
@BidwellCanyonFarm3 жыл бұрын
Thank you, I hope you can get her squared away before it is too late.
@michaelhuskey32253 жыл бұрын
The extra details you add to your videos are extremely helpful. Thank you for "thinking out loud" so that the rest of us can benefit from your experience. I just subscribed.
@BidwellCanyonFarm3 жыл бұрын
Thanks for the comment Michael!
@lawrencesmith65364 жыл бұрын
Great informative video, dude. Especially that little trick of using pipe dope under the teflon tape. Wish I woulda known that about 40 years ago. Cheers
@BidwellCanyonFarm4 жыл бұрын
Thanks Lawrence! Yeah, the pipe dope trick saved me a lot of time over the years. Best to you my friend!
@pauldominic21503 жыл бұрын
Vey good and informative. Cool rebar trick!
@BidwellCanyonFarm3 жыл бұрын
Thanks for the comment Paul!!! I have also used heavy duty concrete stakes and shortened T posts in the past.
@erikbrantner42954 ай бұрын
Woodford is a good brand of hydrant for both residential and commercial use.. I have two on my premise that I installed almost 16 years ago.. No problems, just once in a while I would have to Tighten up the retaining nut below the handle and put a little packing in first
@BidwellCanyonFarm4 ай бұрын
Nice! We are heading into our 10th year on 5 of the hydrants here at the farm and they haven’t needed any maintenance yet.🤞
@papadigiannip63493 жыл бұрын
“Don’t fake it….this is real life guys. “. So funny BT. You continue to show what an amazingly genuine guy you are. Miss you bro. Keep it all up.
@BidwellCanyonFarm3 жыл бұрын
Not sure who this is, but you sound like family! Much love to you and yours. Thanks for dropping a comment!
@Joe-re9ex2 ай бұрын
Very informative
@BidwellCanyonFarm2 ай бұрын
Thanks Joe!
@lawrenceklein3524 Жыл бұрын
Installed two hydrants in our area last year to water the livestock. One of the best improvements on the place! However, I didn't even think of taping the pipes! Dang! Must be specific to your area, as I've never heard of it up here in Northwestern Michigan. Good idea on the gravel bucket, too! Great video! Thanks!
@BidwellCanyonFarm Жыл бұрын
Nice! Yeah you should be fine without the tape for a good long while. I think it probably just adds a little extra protection out here. Our soil can be pretty brutal on things as well as the water. Some wells even have an iron eating bacteria! Yikes!
@tonywalters9436Ай бұрын
Pipe dope holds the tepline holds in place that one up on me
@BidwellCanyonFarmАй бұрын
It comes in pretty handy!!!
@pizzatheface3 жыл бұрын
I'm dealing with good ol' springtime in Idaho. Having to replace 2 hydrants, but I've noticed the owner used PVC underground. Your video was entertaining and informative enough that I've subscribed, and look forward to watching more!
@BidwellCanyonFarm3 жыл бұрын
Hi Russ! Thanks for the sub! One may consider being pretty careful with the PVC to galvanized joint. I always add an additional stake, t-post chunk or whatever I have laying around to anchor the hydrant at the bottom with pipe clamps around the hydrant and stake so there is little to no movement at that joint. Good luck!
@StoneKathryn9 ай бұрын
Love the rebar cross supports near the top of the hydrant! I'll do that too! Only thing I had trouble with in your video was when you put your pipe wrench on the outside of the pipe of the hydrant. I've been told to NOT do that and to only put a pipe wrench on the hex on the brass part at the bottom of the hydrant. I put a little 2 1/2" brass nipple (1/8" pipe) into the weep hole and then someone said they put a plastic bottle with the side cut out of it to cover the brass nipple and protect the gravel from wedging over the nipple so when you put the bucket over it and fill it with gravel it has some space that the gravel can't get in to block it off. I like your elbow drainage hack. We have a 39" frostline and we had to get a bury 6' Woodford frost free hydrant. We have clay soil so we were disappointed to see NO gravel around our weep hole and no elbow either! It didn't ever break because of the weep hole getting clogged. The handle broke and we can't adjust the nuts to stop it from dripping all the time. We couldn't have gone through this winter like that. We heard that the Woodford brand frost free hydrants are more trouble free and easier to adjust. We decided to go with that since we don't want to do this again. We only have shovels and a post hole digger. My husband dug for 10 1/2 hours doing steps down to the bottom of the hydrant. I'm so happy you posted your install. Thanks so much! We really don't want to do this again! Our old hydrant was a Conrad which I can't find anything about on the internet. The handle was bending out so it was very hard to close the hydrant and then we couldn't even get it to shut off all the way. So frustrating! We'll like this kind where you don't have to lift the handle all the way to get water and you can adjust the flow. Thanks again!
@BidwellCanyonFarm9 ай бұрын
Hi Kathryn! Glad the video helped. 6’ is a long way down!!! I have had really good luck with poly pipe and stainless fittings for the main hookup. The flexibility and durability of the poly makes a great connection that I don’t worry about breaking. I have had to change so many PVC connections at the base, but never any poly or Pex. Thanks for the comment! Hope your project goes super smooth!
@StoneKathryn9 ай бұрын
@@BidwellCanyonFarm Thanks! It'll go well with your help! Just have to unhook and put the new one and new nipple on. I'll try the cross rebar too!
@brucefoster89564 жыл бұрын
Assisted a few times on "the dig part" for repair at a friends retreat at Davis Lake. Quite a process.....Great video!
@BidwellCanyonFarm4 жыл бұрын
Thanks for the comment Bruce! The dig always needs some good volunteers!
@kermitmccourt4 жыл бұрын
absolutely fantastic! , ive always wanted to see what the install looks like, I wish i could subscribe 15 times. Wilder loves your videos as do I.
@BidwellCanyonFarm4 жыл бұрын
Well, you can tell Wilder that I love him very much and I love you too brother!
@phoenixfireclusterbomb3 жыл бұрын
Thank you for going into the details and explanations. You have a natural talent to teach. Thank you for making the world a little easier.
@BidwellCanyonFarm3 жыл бұрын
Nice! Thank you Matthew. I really appreciate that.
@Likadees Жыл бұрын
I changed two out at my buddies farm. I use the sonotube but before that; i stabilized the pipe by bounding the steel T-Post deep down the hole and leave about 6in. above ground level and tie it with five screw clamps! Great job tho!
@BidwellCanyonFarm Жыл бұрын
Nice! Sounds like that lil puppy dawg isn’t going anywhere anytime soon. Good on ya!
@jmorrisonjr862 жыл бұрын
My hydrate just failed and this is exactly the video I needed!
@BidwellCanyonFarm2 жыл бұрын
Sorry to hear that your hydrant failed you. Here is to a successful swap! Best
@bradfordtownsend22143 жыл бұрын
Seen some replacing galvi with brass. The galvi developed a hole which caused a leek.
@BidwellCanyonFarm3 жыл бұрын
Thanks for the comment. Yeah, I have heard of some troubles when you start mixing metals.
@glendasmith24353 жыл бұрын
Thanks, excellent video . Picked up lots of tips.
@BidwellCanyonFarm3 жыл бұрын
Thank you Glenda! Glad it helped.
@kylethelincey2 жыл бұрын
I appreciate the video. Easy to follow and understand.
@BidwellCanyonFarm2 жыл бұрын
Thanks Kyle!
@johnfarrell31713 жыл бұрын
Hey Brian. Another helpful "trick up the sleeve" is to use a short length of Sonotube (if it's available of course) to contain the gravel for drainage, provide lateral stability and keep the pipe itself from direct contact with ground water through the backfill.
@BidwellCanyonFarm3 жыл бұрын
Nice tip! I never thought about a sonotube for this application. Do you think they will last underground? I know they are harder than all get out to peel off a concrete column. Thank you for the comment!!!
@kaczara132 жыл бұрын
great job! I appreciate the info ., yes I will test before back filling!
@BidwellCanyonFarm2 жыл бұрын
Awesome! Thank you!
@aron7up3 жыл бұрын
Just seeing how much you saved us all, that watched this. How much would you charge someone to do this if they already bought the new valve?
@BidwellCanyonFarm3 жыл бұрын
There are a lot of factors to consider with the cost of an installation like this. If it is just a straight replacement with no problems in the mainline etc. it would probably be somewhere in the ballpark of $240-500 and take approximately 4 hours to complete. However, if there are issues with other plumbing the price could go way up. One may consider hiring a licensed plumber for the job. Best to you Aron!
@kehindejones Жыл бұрын
Thanks
@BidwellCanyonFarm Жыл бұрын
You betcha Marvin!
@Huskinmatt3 жыл бұрын
Hell yeah - I too often toss aside Debras
@BidwellCanyonFarm3 жыл бұрын
Haha. Debras everywhere!
@Esptrailrider6 ай бұрын
I need you to do a video on the filter. That is interesting. My water is so full of iron its crazy
@BidwellCanyonFarm6 ай бұрын
Next time I install one I will try and make a video about it. Is the iron in particulate form like from the sides of your well casing? Or more of a discoloration?
@idahopotato58372 жыл бұрын
The Teflon tape should be put on first before the dope so it is a tighter bond. Just using the dope is fine on a metal to metal contact. The tape is good on plastic pipes and can be used on metal but isn't really necessary. I use tape only when I fear contamination.
@BidwellCanyonFarm2 жыл бұрын
Thanks for the comment! I will probably stick to the tape over the dope, since it has worked for me without fail for nearly two decades, not to mention the time it saves hassling with tape slippage (especially when working in a hole or trench). Is there some science out there with a case for the tape under?
@sheliabennett39784 жыл бұрын
Really helped me
@BidwellCanyonFarm4 жыл бұрын
Glad it helped you!
@joeshittheragman1 Жыл бұрын
thanks man.
@BidwellCanyonFarm Жыл бұрын
Hey, any old time partner!
@griffinranger23823 жыл бұрын
Good job, very informative!!
@BidwellCanyonFarm3 жыл бұрын
Thank you!
@dalehaub9440 Жыл бұрын
Genius!
@BidwellCanyonFarm Жыл бұрын
Thanks Dale!
@summerbode52429 ай бұрын
Thx for great video…what would you charge for what ya just did, labor and material, and how long was total job?
@BidwellCanyonFarm9 ай бұрын
There was probably $200 wrapped up in parts and $450 for 6 hours of labor at $75/hr. $650 total for what was done in this video.
@johnfarrell31713 жыл бұрын
Curious LOL, the "What can I do now so I'll never have mess with this PITA again" ideas people can come up with . . .
@jerex112 Жыл бұрын
good job
@BidwellCanyonFarm Жыл бұрын
Thank you J King!
@immattyice76692 жыл бұрын
Question - mine just froze and there it’s noticeably cracked on the red portion where it threads onto the steel pipe. Do you think I can just swap out the handle to avoid digging up the entire 5 feet of dirt?
@BidwellCanyonFarm2 жыл бұрын
I would say most likely, I have never swapped the head out myself so I don’t know for sure. I hope you find a way to save yourself from digging! Good luck
@deanstoops26 Жыл бұрын
@@BidwellCanyonFarm The head could be changed if you can get it off. Most likely it is rusted tight. When I had one freeze I removed the handle, pulled the rod out and welded the head. You must use cast iron welding rod. It helps to warm the head up with a torch a bit before you weld it.
@Harliquinn92 жыл бұрын
Great video, thanks! Why did you change the 90 degree street elbow, though? Is there often a problem with that being clogged or something?
@BidwellCanyonFarm2 жыл бұрын
The water in our area has an iron eating bacteria that causes buildup on the inside of fittings eventually restricting the flow. Any plumbing I get into around here I end up changing out a few fittings. Thanks for the great question!
@marinbalan352Ай бұрын
Can you put a link for the 90-degree elbow into the drain valve please? Thank you!
@BidwellCanyonFarmАй бұрын
amzn.to/3LdzvEi 1/8” Street elbow
@marinbalan352Ай бұрын
@@BidwellCanyonFarm Thank you!
@rmox5 Жыл бұрын
I’ve got a slow underground leak running to my hydrant. In your opinion would replacing the plunger possibly fix it? I have noticed a difference in tension opening and closing the lever
@BidwellCanyonFarm Жыл бұрын
Hi Robert, sometimes you can make adjustments to the plunger travel nuts at the handle. These can usually be adjusted to increase travel or decrease travel depending on what you need. You could also get a replacement plunger kit and replace the plunger without having to dig anything up. Hope this helps!
@carloscarlos7044 Жыл бұрын
What exactly was the layment you put on top of the gravel bucket ? Also is making the standpipe connection to a poly pipe mainline the same process ?
@BidwellCanyonFarm Жыл бұрын
Hi Carlos, that product is called prodex. It was a scrap piece of house wrap radiant barrier i had leftover from a job. It is not for this application but it works. You can use anything that won’t allow fine dirt or silt into the gravel in the bucket. It probably isn’t even necessary, but i like to put something over my buckets. I actually have a video connecting poly pipe to a yard hydrant. The process is a bit different. Let me know if you find it. 🙏
@carloscarlos7044 Жыл бұрын
@@BidwellCanyonFarm thanks , just got done watching it , very informative .
@mikebarry34915 ай бұрын
Hey what size 90 degree elbow (threads ) did you use for the drain port on the hydrant
@BidwellCanyonFarm5 ай бұрын
Hey Mike, it is a 1/8” iron pipe thread. I like to use a street 90 coming out of the hydrant in stainless or brass then a short nipple facing downward, a 2 to 3” oughta do the trick.
@mikebarry34915 ай бұрын
@@BidwellCanyonFarm also my area calls for a 36 inch depth pipe but the spec sheet says that will give you a 27 inches above ground for the Spicket. Would it be OK if I went with the next size longer hydrant so it’s higher off the ground I don’t need to bend over as far for every time for hooking it hose up.
@jayvanvoorhis52932 жыл бұрын
I have to replace a hydrant in my backyard it's the only hydrant I have and I'm wondering if I should bleed off the pressure at the hydrant because the pump is under the house in the crawl space then I worry about having to prime the pump afterwards
@BidwellCanyonFarm2 жыл бұрын
So Jay, you do not have a submersible pump correct? It is one that sits on top of the well casing and draws water up from the well through a pipe right?
@Customsouthernarms2 жыл бұрын
Awesome video. I'm looking at getting a few of the Y34's. What I can't get my head around is how does the weep hole not leak while the hydrant is in use?
@BidwellCanyonFarm2 жыл бұрын
I pondered that for awhile too. Pretty sure the plunger seals against the drain hole opening when the plunger is pulled up and water flows through the Little curved profile part of the fitting. Pretty ingenious design really.
@toneycollins63772 жыл бұрын
You are correct, the plunger seals the main water line flow when the handle is down and opens the drain hole. When the handle is up the plunger seals the drain hole and allows water to flow through up to the faucet. Very well designed and has been around for years.
@BidwellCanyonFarm2 жыл бұрын
@@toneycollins6377 I love good designs that work!
@magickladycj2 жыл бұрын
I know this is an old video. There was a hydrant in the yard when I moved in.... although it was run over and just pulled out.... can I dig and put in another hydrant new one due to I have to do another one that froze this winter as well..... or do I have have to dig the whole yard up ...
@BidwellCanyonFarm2 жыл бұрын
All you would have to is to dig up each spot where the water line is and you want your hydrants might need to T into the mainline where you want to add the new one, but the location of the old one should be pretty easy. Do you know why it froze? Make sure your water lines are deep enough, or else it might be the whole yard.😬
@zapzpzee3 жыл бұрын
Ugh. I am watching this because our hydrant just like that failed. That plunger thing bent, so it can turn on, but good luck shutting it off! We got a different kind to match the rest of our hydrants (that all work great and can’t bend at that weak point), but we only got the top part, thinking we could just unscrew the top and screw on a new one....apparently that’s not how this is going to work and we need the whole giant expensive thing. It’s in a bad spot so we might just cap it and not use it.
@BidwellCanyonFarm3 жыл бұрын
Bummer! Sorry to hear that. Hope you figure out a good solution so you never have to go there again. Best of luck homie!
@YoutubeSucksAnus3328 Жыл бұрын
Boy the next guy is gonna hate you in 100 years lol
@BidwellCanyonFarm Жыл бұрын
Haha, that’s the goal. At least it isn’t me!
@thisplaceisazoo Жыл бұрын
@@BidwellCanyonFarm You never know. They might forget to turn off the hydrant in a year or two and have you come back and dig out all those rocks again! lol
@d1bigshifter7373 жыл бұрын
Just curious as to why you didnt just replace the head and stem instead of whole unit ?? Was it leaking at the well ??
@BidwellCanyonFarm3 жыл бұрын
Thanks for the comment. Personally, I would rather put in a new Woodford and let the next generation worry about it. I have no idea what make the original was, nor if I could track down pieces and parts for it. Not quite sure what you mean by leaking at the well? Is that what you call the base of the unit?
@johnkuiper66076 ай бұрын
Absolutely no galvanized fittings!
@BidwellCanyonFarm6 ай бұрын
I agree! Been using a lot of stainless fittings lately! How about you?
@Rich-oo9wq2 жыл бұрын
I purchased a Woodford Y-34 3 Ft Bury 1in. x 3/4 in NPT x MPT galvanized steel pipe yard hydrant, like the one you installed in this video. I don't have it yet and am wondering what size are the threads at the bottom where it will connect to a 90 degree street elbow. I want to make sure I can get the correct fittings for my installation. Any help would be appreciated.
@BidwellCanyonFarm2 жыл бұрын
Hi there Rich, thanks for the comment! You are going to want to pick up a 3/4” NPT street 90. The 3/4” MPT (Male Pipe Thread) on the bottom of the hydrant is also a NPT (National Pipe Tapered) fitting. It just lets you know if it is male or female.
@Rich-oo9wq2 жыл бұрын
@@BidwellCanyonFarm Thank you for your quick response to my question. Your expert video and tips on this installation will assist any novice to accurately replace any similar yard hydrant. I have subscribed and will watch more of your videos, also recommending you to my friends.
@Rich-oo9wq Жыл бұрын
@ Brian - I installed my yard hydrant just the same as you did here including the rebar braces which help to secure side to side support. Also I used a plastic bucket with cleaned washed gravel in the hole around the bottom of the hydrant for necessary drainage. My old pump failed because of dirt in the small drain hole and froze in winter months. Your installation video was a great help and I hope you continue to provide similar videos. Thank You !.
@Seabee1970 Жыл бұрын
How you know there no leaks b4 u fill it in
@BidwellCanyonFarm Жыл бұрын
I tested the pressure while the camera battery was kaput, backfilled the hole etc. and didn’t feel like digging it back up to film the pressure test. Oops!
@williambotts6352 жыл бұрын
I have a tiny leak at the elbow on mine and it has only been in the ground for a few years. I dug it up and found a small drip, is there a way to seal the leak without digging up more and replacing anything? A friend said he could touch weld it at the spot it's leaking and seal it as it isn't spraying just dripping about a drip every 1.5 -2 seconds. Thanks for any help.
@BidwellCanyonFarm Жыл бұрын
Not that i know of William. Sometimes sediment from the wall will plug it up over time without having to do anything. Are you on a well? Or city water?
@williambotts635 Жыл бұрын
@@BidwellCanyonFarm City water, i counted and the little triangle on the meter makes a complete turn in 10 seconds. Will a drop every second or two do this? or will it be a bigger leak? Thank you so much for your help, I am on a fixed income and any help is greatly appreciated as I have to do the work myself.
@richardtownsend6951 Жыл бұрын
Problem never disclosed…. Water table, (sewer affluent), etc., will enter your drain, freeze and burst your hydrant.
@BidwellCanyonFarm Жыл бұрын
Eww sounds gruesome! Luckily this one didn’t have anything like that going on. It was a cracked head. I think it must have had a hose hooked to it when the temperature dropped below freezing and split the head wide open.
@daniellupisella4282 Жыл бұрын
Where did you pick up the stainless steel drain plug/valve?
@BidwellCanyonFarm Жыл бұрын
Hi Daniel, I swooped those lil puppy dogs up on Amazon. Got them awhile ago. Not sure what the availability/price is looking like these days.
@daniellupisella4282 Жыл бұрын
@@BidwellCanyonFarm, thank you!
@tmontana2134 жыл бұрын
Whats the size of that drain elbow? 1/8in?
@BidwellCanyonFarm4 жыл бұрын
Yes. 1/8" drain elbow. I like using stainless even though it is a bit more expensive. Brass would be the next best. I also like to put a 2" nipple pointing down out of the bottom of the elbow to make it extra hard for sediment to travel up the drain spout. Thanks for the comment!
@garymolina21574 жыл бұрын
Why did you not simply service the existing hydrant? How did it "fail?"
@BidwellCanyonFarm4 жыл бұрын
Hi Gary. Apparently the hydrant split after a hard freeze with a hose connected to it. No service could bring that baby back.
@markpurdin9900 Жыл бұрын
I used a brass elbow for the drain, any ideas how it compares to SS. Anyway my wife didn’t want me install like I did before, the PVC broken, lasted 8 years. I’m a cancer survivor and lost a lot of strength. The company that did didn’t recommend the bucket/gravel even though I used it before.
@BidwellCanyonFarm Жыл бұрын
Hi Mark, Brass makes for a fine drain as well. I really like the poly pipe for my hydrant installs nowadays. For one, it is way cheaper than pvc right now and the natural flexibility of it alleviates the cracking like you get with the pvc. As long as you install it in a bed of sand, which helps avoid rocks from kinking it, i feel like it will last a long long time. I have always used the gravel and bucket method, but i am sure you will be fine without it, as long as there is not a lot of clay or fines in your sand that could potentially plug it up. Glad to hear you made it through the battle with cancer. Next step get your strength back. Maybe some yoga? Thanks for the comment! Best to you and yours. -Brian
@markpurdin9900 Жыл бұрын
Thanks I had metastatic melanoma, cured now after 5 years. Immunotherapy made me weak, the Yervoy. They wrote down to use 1/2 play sand then 1/2 topsoil. Red dirt (clay) in Oklahoma. Would that be Ok, to not use gravel. They used pex to make the connection. I’m on a well, and yes they checked the well tank.
@markpurdin9900 Жыл бұрын
Also please wear sunscreen, a big hat and good sun glasses.
@BidwellCanyonFarm Жыл бұрын
@@markpurdin9900 Copy that!
@croftjenniferfarmcroftdesi31256 ай бұрын
Where did you buy the stainless steel elbow that you screwed into the elbow at 7:45 into the video? Thanks!
@beyforghani79622 жыл бұрын
Nice job! What do you charge for this job? thanks.
@BidwellCanyonFarm2 жыл бұрын
I charge time and materials as well as a materials handling fee so i think all in all this came out right around $500.
@4wdaddict412 жыл бұрын
Why do you need to replace the elbow ?
@BidwellCanyonFarm2 жыл бұрын
The water is super hard on galvanized fittings out here. I have found some of them nearly sealed shut from mineral buildup. I found it easier to replace them while I am down there.
@GOBRADON5023 жыл бұрын
Can't you just replace the faucet itself or you have to do the whole stem?
@BidwellCanyonFarm3 жыл бұрын
Hey Tiger, often times you can replace just the guts. I’m this instance the top was cracked and could not be fixed.
@GOBRADON5023 жыл бұрын
@@BidwellCanyonFarm ok thanks the problem im having with mine is I can open it up all the way but there's not a whole lot of pressure like there used to be and when I turn it off it doesn't leak so I'm not sure what the problem is with that.
@jayvanvoorhis52932 жыл бұрын
Priming the well after?
@BidwellCanyonFarm2 жыл бұрын
Do you have any sort of shutoff between the pump and the hydrant? Just close that, then turn off water heater breakers, then undo hydrant. Might have to wait awhile till the water drains into the soil.
@brendapowers70242 жыл бұрын
plumb
@BidwellCanyonFarm2 жыл бұрын
Yep
@MERF2021 Жыл бұрын
how much do you charge for a job like this?
@BidwellCanyonFarm Жыл бұрын
With labor, materials, travel, etc. you can expect to pay $500-750 if you hire this out. If you DIY, you are looking at $250-$350 depending on fittings needed, etc..
@jamesbush66162 жыл бұрын
what size was that drain plug elbow?
@BidwellCanyonFarm2 жыл бұрын
Drain plug is a 1/8” stainless street 90
@bahamut85912 жыл бұрын
hey, do you know the make and model of the hydrant you took out?"
@BidwellCanyonFarm2 жыл бұрын
Wish i could help you, but i can’t. I might be able to find it online tho.
@bahamut85912 жыл бұрын
@@BidwellCanyonFarm i've been looking for a long time but cant, i have the same one and have a part on it broken, been trying to find replacement parts for it
@frankcastle64293 жыл бұрын
Must be nice not to have your hole full of water because the previous owner buried it next to the well!
@BidwellCanyonFarm3 жыл бұрын
You betcha!
@mfawls96243 жыл бұрын
Oh...is THAT why I'm digging in a foot and a half of wet clay right now? I knew what I was getting into with digging a 2x2x2 hole by hand in my region (well, I did forget about the whole network of pine tree roots and runners from all the bushes planted around it), but I didn't reckon on it filling with water faster than I could dig. My main concern is that I can't see anything in the hole as I dig. The well guy told me I need to watch for an electrical wire. I thought he meant running to the hydrant, but now I'm thinking he means the wire going from the house to the pump. Either way there will also be the pipe coming in and probably a wire somewhere running from/to whatever. Maybe I should turn the power off for the last 8 inches or so of the hole depth?
@loui91022 жыл бұрын
✊
@BidwellCanyonFarm2 жыл бұрын
🤙
@RexMoore19842 жыл бұрын
No leak check prior to filling in your hole? Maybe you didn’t video it.
@BidwellCanyonFarm2 жыл бұрын
By the time I realized the camera was not recording, i had already backfilled the hole. 😬 so i went with it.
@jerryrogers5233 Жыл бұрын
Good advice with water heater breaker, pipe dope, bucket of gravel, rebar, and tape. Why not just rebuild the valve with new packing rings, nuts, and dick?? Replacing the whole thing, buried elbow and all seem over kill.
@BidwellCanyonFarm Жыл бұрын
Hi Jerry, The head was cracked on the old hydrant, think it must have froze with a hose hooked to it. 😬
@HHI4552 жыл бұрын
MASSIVE pipe wrench?
@BidwellCanyonFarm2 жыл бұрын
Sure, there’s bigger pipe wrenches out there Early. I take it you have used some?
@atilladeniz3 жыл бұрын
Hii man! hope you are well! nice channel like the video also! keep it up! if you have time please visit my new commercial video about bmw and corona haha i hope you like it