ENIG= Electroplated Nickel Immersion Gold, which is the normal gold finish where you don't need hard plating for edge connectors etc., but want a very flat surface for fine pitch SMDs, QFNs etc.
@Shinji_Dai7 жыл бұрын
From what I found its actually Electroless Nickel Immersion Gold, where the Nickel is deposited without needing to pass an electric current through the solution. en.wikipedia.org/wiki/Electroless_nickel_immersion_gold
@SidecarBob7 жыл бұрын
Years ago it used to be popular to make "armatures" for trees for model railways from telephone wire twisted together in more or less the same way. When finished by wrapping the main trunk with floral tape and painting it with plaster for texture and then adding foliage (coloured ground up foam rubber) the results can be very realistic.
@BvP707 жыл бұрын
Best quote ever: "Lead based solder, for te maximum soldering pleasure!"
@mulgerbill3 жыл бұрын
It's probably a bit late for a chance at a kit but what the hell I'm still jealous af at your soldering skills, you did the whole assembly faster than it took me to replace the grindy little 40mm fan in my ioniser/ozone generator with something a little quieter
@curtaintwitcher11487 жыл бұрын
Clive I have ip65 rated led down lighters that we use at work. These fail alarmingly regularly despite costing upwards of £15 each! If interested I could send some too you for a future autopsy video. Love the channel keep up the good work.
@DjResR7 жыл бұрын
Same thing, a lot of times the bond wires inside the LED elements break (instead of a PSU failure)._
@curtaintwitcher11487 жыл бұрын
DjResR they just end up flashing randomly. I figure it's a component on the aluminium board that's at fault rather than its driver. Shame really given their cost and modest heatsinks installed.
@samplews7 жыл бұрын
Since I need to comment I'll take the opportunity to give you my heart felt thanks for getting me back into electronics after a 15 year hiatus (A Level Electronics!) and its now brining me an immense amount of pleasure, so thanks Clive!
@paulraezer22537 жыл бұрын
Clive, I have to tell you, I was trained in radio electronics in the army, but I have learned much more, watching your videos than the army taught me. I have really enjoyed watching these past few years! Very entertaining, and educational. Not after the kit, just want you to know, you're appreciated. Thank you so much!
@paulblitz6 жыл бұрын
I've now had 6 lots of double-sided PCBs done by Seeed, and in all cases the quality and price were both excellent. If you order multiple designs at the same time, then the per-board cost drops quite a bit, due to the combined postage costs. They also offer DHL delivery - costs a little more, but is faster.
@zZBucketsZz7 жыл бұрын
Pink cable ties? Hot damn, I'm in.
@OAleathaO7 жыл бұрын
10:50 - 11:11 --> BigClive pre-crimped 340 terminals? Now that's some serious dedication for his viewers.
@bsvenss27 жыл бұрын
˙uʍop ǝpᴉsdn ʇᴉ pᴉp ǝɥ ʞuᴉɥʇ ʎllɐǝɹ I puɐ
@chmarr7 жыл бұрын
I legit personally know how he feels .... but I have worked in electronics and I have had to do the job he's did ... except he's only had a taste what hell I went through doing that crap 12 hours a day 6 days a week ... I would rather tickle a rattlesnakes balls than do that crap again.
@Kasatome7 жыл бұрын
How's Australia?
@thatrudager7 жыл бұрын
Plus the 17 from the kit he assembled in the video. And I'm sure he made a couple extra on top of that.
@macdonalds19727 жыл бұрын
The ones from the kit Clive used in this video are included in the 340. (20 PCBs x 17 terminals = 340) And every kit has 1 extra as only 16 are used.
@generedwine68634 жыл бұрын
Cool led tree Clive. Really enjoy your videos and learn a lot from you. Really wish I could afford to be a pateron. Sorry. Just keep up the fun work. Even us retired 75yo disabled vets enjoy learning new things or just being entertained with your shows.
@Markle2k7 жыл бұрын
High CRI is easy to explain, it's like having less ripple by adding phases to your input. They use more colors of phosphors and carefully proportion them to more closely match the human eye's response curve. You'll see fewer dead spots or weak colors in apparently white light.
@somedutchguy75827 жыл бұрын
ENIG: Electro less Nickel, Immersion Gold A completely chemical process that puts about 0.1µm of gold over a few µm of nickel.
@FirstLast-lt7xe7 жыл бұрын
Clive, you have on of the best electronics tear down and circuit board exploration channels out there. Keep uploading the good content.
@jimmuse30107 жыл бұрын
I enjoy your videos because I've always enjoyed taking stuff apart to see what makes it tick. I also save a lot of broken items rather than tossing them because maybe some part of it might be useful later on. Recently, after a lightning storm, two LED tubes in the basement got zapped. I was curious what exactly got zapped, so I took it apart and found the LED strip was unharmed but the little power supply had a chip blown out of the chip in the power supply. The LED PC board has cob LEDs arranged in groups of 5 parallel and 24 groups in series. What I wound up doing was cutting the pc strip into 2 pieces of 11 groups and 1 piece of 2 groups and used all 3 in the kitchen as under counter lighting. Since I have 3 HP printer 32v dc power supplies, from friends that gave me their old printer that no longer worked, I was able to use one of them to power the 2 eleven group strips and I used a Canon 6v DC wall wart (from what, I know not). I just thought you are one person who could appreciate that story. Keep up the good videos. Jim
@NoRouteToHost7 жыл бұрын
A lead based comment. We don't want any of those lead-free comments :)
@DaveCurran7 жыл бұрын
With DIrtyPCBs, it's worth changing from protopack to qty 10, and setting the actual size as that sometimes works out cheaper. Also check 20x and 30x as sometimes they come in at the same price as 10x.
@100roberthenry7 жыл бұрын
yep i do that too on dirty pcbs. ;)
@KarlKornel7 жыл бұрын
This is kindof interesting: It looks like SEED can also do the assembly, which sounds cool if you've already done some test boards, and then you want to miniaturize it. I also hope you'll be able to do videos while you're out and about! Those were always interesting.
@bigclivedotcom7 жыл бұрын
i intend to set up the "studio" on a random flight case as soon as possible. I'll be trying to put up a lot more videos than I did while I was travelling last year.
@denislostinlondon1997 жыл бұрын
Off-cuts of brown copper clad board and an etch-resist pen. Happy days.
@ryanmacewen5114 жыл бұрын
THAT stuff never worked for me. Was great fun though.
@johnhutchinson53985 жыл бұрын
This is one of the best informative videos about two totally different companies and pub,s and how they are made. I’ve watched this video twice along with a few other s. Thanks for all the great info on different electronic components. I never went to any kinda schooling for electronics. I learned it mostly on my own with the help of a great friend in , Porter, Texas. Mr Sonny Eires. He learned everything about communication electronics when he was in the navy. There’s nothing he couldn’t fix or build from scratch. I learned to work on cb radios and amps. I even designed my linears. I built com a little 50 watt driver to 6000 watt amps. I even helped sonny develop what we named a, dead motor mall. When you keyed up your radio to activate the amp , the motor mall would change from 12 volts to 24 volts. You could use as many 12 volt batteries as you had space for. I’m retired now and piddle around the house and always looking for something to build or fix. Thanks. John.
@DTAChako7 жыл бұрын
I've been watching your videos a lot lately while doing breaks from studying for my Electrical Engineering exams. They are perfect to relax and simultaneously learn much about bad chinese product design.
@jojoposter7 жыл бұрын
Dennis Witzig the bob ross for electrical engineer(ing students) ;)
@mikethedigitaldoctorjarvis7 жыл бұрын
+ Niklas Mertens........I agree except Clive doesn't beat the devil out of his tools :-)
@joshbobby7 жыл бұрын
If you put this on your website as a kit, I'd be willing to pay for it, as it's such an interesting looking "tree", especially with the colour changing LEDs!
@torqued6667 жыл бұрын
Same here.
@wisher21uk7 жыл бұрын
and me :)
@jameswhite96627 жыл бұрын
JJ TECH same
@kasnitch7 жыл бұрын
I would love one of those lamps to sit on my computer . it will give me a good reason to get a proper soldering station and muck about with electronic kits during the long winters
@misterhat58237 жыл бұрын
Just use a cheap USB power supply.
@wouterkuit35087 жыл бұрын
Not sure about the odds, but did want to let you know your videos inevitably make me giggle, snort, or laugh out loud at least once every video. I love the comments and the 'basic' setting that doesn't distract the viewer. Keep up the great work!
@otopico7 жыл бұрын
Here's my comment. Thanks for the years of entertainment and information. Watching you tear down the deadly pink devices from China has made my world a little safer and a lot more appreciative of well engineered electronics.
@crpeterson147 жыл бұрын
Better odds of winning a kit than getting stuck by lighting. I'm in :)
@BaronVonBeef7 жыл бұрын
Great little kits you've got there, Wouldn't mind being able to buy them from your website
@MovingTarget.7 жыл бұрын
Max Beefsteak 👍
@cryxli7 жыл бұрын
The explanation of the PCB manufacturers' pages is very much appreciated!
@goranandersson35447 жыл бұрын
Skip the rest of the video? No way. Watching soldering is mildly interresting, but it's all the stories and knowledge that you so willingly share that makes it so nice to watch. :)
@osholt7 жыл бұрын
Gimme da multimeter!... wrong channel
@hoytdotblohm7 жыл бұрын
Oliver Holt nice
@DoRC7 жыл бұрын
Oliver Holt who is giving away a multimeter?
@m816327 жыл бұрын
Do R/C! electroboom
@electrospark2957 жыл бұрын
Lmao
@vmailtk57 жыл бұрын
gimme a 3D printer. oh wait, wrong channel. please send me a kit and send Jullian a spludger.
@OtusAsio7 жыл бұрын
You are very kind to your viewers... always fun to see you do tear down and explain the circuitry...
@erikprins89787 жыл бұрын
Lead based, for all your soldering pleasures. Hmmmmmm nice
@KnowledgePerformance76 жыл бұрын
Only way to do it properly...
@MvRens7 жыл бұрын
I love the smell of lead in the morning...
@MegaMetinMetin7 жыл бұрын
Doug Reed shrinking balls
@doorguner017 жыл бұрын
Doug Reed gunpowder! well at least for us Americans in the USA!
@chrisc77077 жыл бұрын
I'd have to agree. Lead free solder just lacks that sweet smell :(
@bren1067 жыл бұрын
In your pencil?
@KolorowaSowa7 жыл бұрын
You should consider selling those kits. I would like to buy one.
@lossycodec93057 жыл бұрын
The concept of getting a custom printed board that affordably is amazing.
@stevenott83307 жыл бұрын
I just wanted to say that I love this channel. Your videos have actually gotten me through a really tough time in my life, and have also inspired me to learn to solder and to play around with electronics.
@ADR697 жыл бұрын
these kits are awesome. whoever wins one should record the build process and share.
@daBigR--7 жыл бұрын
Very kind gesture Clive, thnx
@Roamor17 жыл бұрын
Don't mind watching the build for a second time; love to hear your ramblings.
@shaunewing8973 Жыл бұрын
when I worked for this company I was running a EUBANKS 9100 wire machine cutting and stripping and marking MILES of wire every day. also running AMP and MOLEX crimping machines . with the FLYWHEEL and solenoid die. loved that job
@RedSplatGraphics7 жыл бұрын
ENIG is Electroless Nickel Immersion Gold, its a nickel plated pad with a thin flash of gold on top to protect the nickel pad and aid soldering. The gold is removed by the solder, and you solder to the nickel pad. Its becoming the standard lead free finish. its also good for small SMD components, as its flat, unlike HASL which can have bumpy finish
@ezhatiy7 жыл бұрын
gimme da meetah... whoops, wrong giveaway
@stephenf34337 жыл бұрын
Данил Сергин lol
@Firecul7 жыл бұрын
Tbf they moth like causing explosions so easily confused :)
@grimninja20047 жыл бұрын
need to meaure the FULL BRIDGE RECTIFIER
@AlexApol7 жыл бұрын
Данил Сергин *insert monobrow dance*
@JeroenvanMontfort7 жыл бұрын
I already saw the other build video for the LED tree. Still, I can't stop watching this one. Oh dear, I think I need to cut back on watching KZfaq for a while.
@kNasty_7 жыл бұрын
listening to you talk about various lighting effects or electrical stories as you assemble a thing is damn near therapeutic.
@__aceofspades7 жыл бұрын
As some with an apartment, id love to have a year round Christmas tree to brighten up my life. Also clive, may i suggest painting the wire limbs of the tree green, brown or black? If I win id definitely do that.
@mgobluevictor7 жыл бұрын
Would love to get one of these kits, since I am not an asshat!
@anthonycroftcroft78045 жыл бұрын
Love watching your projects Clive, it’s inspired me to get my old soldering iron out.
@Booger69957 жыл бұрын
Your dedication to you viewers is very heart warming.
@burtron7 жыл бұрын
Had no idea getting pcbs made was so cheap at a small scale.
@AttilaAsztalos7 жыл бұрын
It's not, unless you're specifically ordering from one of these two - they're not the ones being mentioned by accident. There might be another one or two less known sources with the same pricing (I don't know of any others), but the typical "hobby PCB" outlet will charge you several times this price, and at $50-100 for ten, when you really just need one single small PCB paying for it stops being fun really fast...
@Monkeh6167 жыл бұрын
One of these two.. or Smart Prototyping, ITEAD, Elecrow, PCBWay, ALLPCB, ShenZhen2U, and certainly a few more. And OSHPark, which has a different pricing scheme (which sucks for this specific example, but is great for some things).
@nickguy68207 жыл бұрын
Love OSH Park for small boards. If you're into SMD and tend to make thing a couple inches square, it's cake. For larger boards, I tend to go with Elecrow, as OSH's pricing scheme tends to end up more expensive with increased size. Elecrow's also nice if you want other options, like solder mask color, etc. Never used Dirty PCBs or Seeed.
@hellcoreproductions7 жыл бұрын
Watching Clive before bed.
@raymondj87687 жыл бұрын
his voice is so soothing isent it !
@seanyem7 жыл бұрын
Hellcore ditto
@seanyem7 жыл бұрын
& ditto
@seanyem7 жыл бұрын
its like a geeks bedtime story of electronic distruction. I don't even understand some of the electronic it find it enjoyable. its deffo the voice but as well I love taking things to bits or building crazy things to enjoy!
@MiTh697 жыл бұрын
lol, me too.
@adabill2953 жыл бұрын
Still interesting, 3 years later. Thanks for your efforts and channel.
@leejones80507 жыл бұрын
Been following for the past year or so Bigclive and your vids are always educational and fun to watch, i've built many items through your knowledge and this video is no exception. I may be trying these sites myself now for some PCBs i have in mind. Keep up the great work.
@SGM2601907 жыл бұрын
Love your vids, Clive! I don't understand much electronics but I enjoy listening to you talking about stuff!
@ozricm7 жыл бұрын
You should sell these kits! Kits are the best way of learning electronics in my opinion.
@ihnwtpu7 жыл бұрын
He actually does sell some kits (www.bigclive.com/shop.htm), but I remember him saying not many people buy them because they are more expensive than cheap kits from eBay.
@Overrice7 жыл бұрын
Electrical engineer here that went through an apprenticeship before going to university. Kits will teach you soldering, and maybe give you some ideas for good PCB design. Breadboards and simulators are better for learning the actual electronics.
@LionkingCMSL7 жыл бұрын
Big Clive, I love your channel as it is very informing and entertaining. I will admit that I love your accent. Just to note I was a radio maintainer for Amtrak and am used to working at the component level, even down to replacing surface mount components with a 25 watt soldering iron.
@HammesHacks7 жыл бұрын
Pros and cons of Dirty PCBs v. Seeed: Seeed is cheaper when you use 1 design per Gerber file because they charge per design. One design could be 4 identical, 4.5 by 4.5 mm boards placed in one gerber file or just one PCB design. When you have multiple boards you will need to add mouse bites in your gerber file to allow PCBs to be separated later. If you need multiple different small boards on the same 10 by 10 board Dirty PCBs is cheaper. You just add all of them to the same gerber file (making sure they are in the 10 by 10 mm area) and Dirty PCBs adds the mouse bites for you. This makes panelization much easier for people new to PCB design. Lastly, if you are in Shenzhen, both will show you factories/how things are made. However, the people at Dirty PCBs are more fun when it comes to beer and BBQ.
@PyroRob695 жыл бұрын
I have used Dirty PCBs a couple of times. Excellent quality, just slow shipping.
@44687 жыл бұрын
I think I speak for quite a few of your fans in saying we'd love to be able to buy one of those kits. Could be a wee business for you there Clive and to change things up different kits each season i.e a festive themed one for xmas etc. they could be ltd edition too :)
@seanyem7 жыл бұрын
Hi Clive. I'm visually impaired (registered blind). I love all your work watched every very... I struggle to soldier with my Vision but have started playing with Microcontrollers as I can get away with bread board and patch wires. but I would love one of your LED Tree's if I could be built. With ym Vision deterioration LED Lighting is my obsession and a must. I lovely the wonders of RGB for pleasure but always have led lighting around me to live day to day from LED Touches, Filitment LEDS to full on ceiling and floors / Video lights.... I would love to be luck to receive a built Tree. keep up your amazing videos. I love watching your video just before bed. chilled out relaxing watching you dismantle the crazy pink things of China. p.s. love the gay darlics. so doesn't my Chinese Husband. we think it's helirious. much love. Sean (and Alex) Yem from Near Liverpool
@mickjames737 жыл бұрын
Sean Yem i also have low vision and have a setup where i use my iPhone on a tripod and use its Magnifier function for soldering. Takes a bit of getting used to but does work
@joeboygsxr7 жыл бұрын
Sean Yem I myself am visually impaired and am registered blind, love soldering it can be defficult at times however with enough practice I have become quite confident in my soldering. Being fully colour blind also doesn't help things as colour plays a big part in electronics as well as in standard electrical stuff however I always find a way to get what needs to be done done haha Keep on soldering!
@joeboygsxr7 жыл бұрын
chrisphobia ha! It just so happens that I build a few FX pedals, did an overdrive last week and a tremolo as well as a PT2399 delay
@thewolfin7 жыл бұрын
Do you guys sub to Christopher Fisher? 'The Blind Woodturner' is his channel name I think. Really interesting stuff!
@marvinweisbeck3585 жыл бұрын
Cool tree. Love your show and led projects.
@1911azkiddennis7 жыл бұрын
You make this stuff look so easy and fun when you put stuff together so thank you for all of the videos you make
@ToxTox7 жыл бұрын
For the maximum soldering pleasure...
@ciarfah7 жыл бұрын
Daniel Olaussen Dual layer for her pleasure
@jameswhite96627 жыл бұрын
color changing LEDs , black and red cable connecting to the pcb with lead based solder going through to the resistors and in a moments notice through the blue poundland cable in the right polarities and held in by a very strong and also pink cable tie to the also poundland battery pack that I exploded this month (but there still good). and that guys and girls is how I back tracked the project I would love to build and hope I win thanks BigClive for the the brilliant video
@TimothyHamm7 жыл бұрын
That is a nice little tree. A good Christmas present for mum.
@kevindinsdale82047 жыл бұрын
Thanks for your videos, I find them most interesting and informative as to me, a layman with just basic knowledge of electrics, you explain in ways that I can follow and understand.
@juanmendes12997 жыл бұрын
GIMME DA MEETTA, i hope this works
@ArpadBelovai7 жыл бұрын
I hope read this Mehdi Sadaghdar too :D
@l3p37 жыл бұрын
To put less stress on the wires: Twist them together before soldering!
@macdonalds19727 жыл бұрын
Good luck soldering them after you twisted them.
@alexatkin7 жыл бұрын
I'm going to have to consider your Patreon at some point as I really enjoy the videos. They have given me the confidence to repair things i might otherwise not have touched, plus know a bit more about what to lookout for with poor built quality.
@relishgargler7 жыл бұрын
I've used Seeed's Fusion service a few times and have always had good results. I've always gotten the thinnest boards available due to extreme space constraints of what I'm putting them in, but even those are well made and easy to use.
@andrewkissel2297 жыл бұрын
I'll stroke your beard for a kit! Only with the grain too, just like a kitty!
@BenEater7 жыл бұрын
.
@6F6G7 жыл бұрын
Another prototyping PCB service you could try is ExpressPCB. This company provides its own free cad software (basic but easy to use). This software doesn't generate standard Gerber files so only ExpressPCB can read and make boards from these files. If you want to design your own boards but don't have a cad program then this service is worth considering.
@mikecowen65077 жыл бұрын
Hi Clive! Another fun project! We've both been in the E-biz about the same amount of time. I'm always amused to see our soldering techniques being nearly identical, despite learning the skills half a world apart.
@curringtonmatthew7 жыл бұрын
My 10 year old daughter would love one of those.
@macdonalds19727 жыл бұрын
Sure, it's for your daughter.
@petermcarthur74507 жыл бұрын
Where do you get your pink cable ties?
@crawfish0697 жыл бұрын
Ebay, Aliexpress, and Dollar Tree should have some. Also Harbor Freight.
@raymondj87687 жыл бұрын
do you want to be thrown across the room by pink cabel ties hahaha
@tirbelain6 жыл бұрын
Looks like a really fun thing to build. Want to go shopping for the components now, to build my own bonsai. :D
@qweiop19987 жыл бұрын
I'd totally purchase this kit to build for myself as a side project from the site if they went up for sale. I really like the look of the tree.
@RicoElectrico7 жыл бұрын
Tnettenba.
@bobbybaggers7 жыл бұрын
RicoElectrico The first rule is you must absolutely tell everybody you know about street countdown.......classic!!
@tin20017 жыл бұрын
bobbybaggers It's basically regular Countdown, but played on the street.
@rozzabuc7 жыл бұрын
tin2001 it can get awfully chilly.
@bustherhimen7 жыл бұрын
Hey Clive where can I pick up a kit? (that is if I don't win)
@PandaMan027 жыл бұрын
if he has the pcb on his website, might have to order a set of parts for yourself
@smudgerdave11417 жыл бұрын
Hey Clive, Standard tinning on Chinese PCBs is HASL (non-RoHS). HASL means Hot Air Solder Levelled and non-RoHS means they use leaded solder. This is IMHO absolutely the preferred option (unless you actually need gold) and any other option is usually at additional cost anyway. HTH
@Baitercell467 жыл бұрын
Having watched you for 2+ years is always nice to know it's helping a bit.
@RadioCaroline1927 жыл бұрын
Please sell the board or kit on web site
@dylnm7 жыл бұрын
BONSAI!
@johnmcdiarmid70107 жыл бұрын
You're a true Scotsman, Clive. You made an offer with no thought to the personal hardships or consequences. Then you regretted that offer!
@lezmellor23914 жыл бұрын
Love watching your videos and your humour in them. Keep up the good work 👍
@adzgtr45257 жыл бұрын
Happy 4th of july, thanks BigClive really enjoying your videos :)
@crawfish0697 жыл бұрын
Happy Treason Day, ungrateful colonists. :)
@PV2Omni7 жыл бұрын
CW Roberts Both of our Countries, got over that a long time ago!
@crawfish0697 жыл бұрын
@PV20mni: I was joking. I'm an American and saw a meme that said that. I thought it was funny.
@ZombieToad7 жыл бұрын
rude words :)
@timw19717 жыл бұрын
34:41. lol
@heffelfinger0077 жыл бұрын
Love having clive on while working, helps keep the day calm.
@jasonbrooks49963 жыл бұрын
This channel got me through lockdown so far. So much to learn - thanks Clive
@magnus33john7 жыл бұрын
Fasinaating. although hospital got me on morphine and anti inlamitories so am barely thinking straight lol
@AwsomeVids837 жыл бұрын
Eric M Get well soon!
@magnus33john7 жыл бұрын
Clotted my iv and when that cleared all the drugs that ended up in the iv tube went into in the space of 2 min. needless to say i apparently turned very white and very fried really quick. Iam surprised i could actually still type lol Thanks for the well wishes but sadly the ms isn't going any where although i can think of a few places i like to send it lol.
@kd8fki7 жыл бұрын
Why don't you give that one to your brother and make his day!
@princelone7 жыл бұрын
love watching these type of videos. I learn so much.
@amorphuc7 жыл бұрын
I'm feeling like a lucky punk! Well, not really but wouldn't it be amazingly fun to receive a kit from my favorite channel? I won't hold my breath. Thanks for your videos Bigclive!
@raarmasu7 жыл бұрын
quite nice set to get, you should sell them at your page
@rvdm887 жыл бұрын
any comment whatsoever!
@xiaowright267 жыл бұрын
A great starter kit to teach my daughter to solder, love your channel!
@quicksc17 жыл бұрын
The electronics Bob Ross, creating unique beauty with electronics and demonstrating with a soothing voice.
@izimsi7 жыл бұрын
I should be sleeping now, but i just enjoy these videos too much.
@AndrewGillard7 жыл бұрын
For a no-page-of-options and generally more professional experience (and a very fetching purple solder mask with gold pads), I can't recommend OSH Park highly enough. I get all of my PCBs from them and they're great. Made in the USA, too! (EuroCircuits are apparently good for more local manufacture, but they don't have OSH Park's purple ;))
@TheRealSasquatch7 жыл бұрын
The only problem with buying anything from the USA is the cost of postage to the UK and then the customs payments VAT etc. can be a real PITA !
@AndrewGillard7 жыл бұрын
I'm pretty sure that OSH Park has free shipping internationally. It takes a couple of weeks to get to the UK, but it's no slower than from China. I've thankfully avoided import fees on my OSH Park orders, though I don't know if I've just been lucky. I've not found that the UK/EU services are sufficiently cheaper for me to give up the purple solder mask :) Plus, I generally etch prototypes at home anyway, so I often have a working board already so the time it takes for the OSH Park board to arrive matters less...
@TheRealSasquatch7 жыл бұрын
I'll check them out. I generally avoid USA due to the hassle - really annoying when I find something on ebay for a reasonable price and the shipping costs are 3 times the price of the item. Had this when I was looking for an M23 12 pin plug - $9 to purchase shipping $47 !!!
@AndrewGillard7 жыл бұрын
Oh definitely it can be an issue. One nice thing with the US is that USPS has flat-rate international shipping stuff which makes "free international postage" options somewhat more practical. I get the impression that they're much cheaper than Royal Mail would be for UK-to-USA, though I could be wrong. I've ordered from a number of US stores with free or very cheap UK shipping and the only real risk is import fees (or, rather, Royal Mail's £8 flat fee! I don't mind paying VAT and duty, but £8 regardless of the item's value is crazy! DHL charged me £4 VAT on something from China the other week; it would have been £12 with Royal Mail...) OSH Park's staff are super helpful and awesome too, btw :)
@guardianlion86227 жыл бұрын
Howdy, Clive! I've been enjoying your channel since just before the New Year. Great stuff! Finally gave me the nudge to set up a proper workstation in my place. Also, for the record, I've never been more nervous about using random USB chargers. Your transformer tear-downs have been eye-opening!
@spartanband127 жыл бұрын
I love your videos, I really learn a lot when I watch them. I went to school to be an electrician but working with electronics a hobby of mine. I love putting kits like those together so I'm always looking for them (mainly to keep me busy).