I'm having the same problem.... I've already changed the version several times and it doesn't link to the radio and it's the same configuration as the video

Hey fellas, I just seen this and youtube didn't give me the notifications. Is the RX and TX bound but you are not getting any stick input? (You can check if it is bound if you look at the receiver manual. I don't recall if they indicate the LED pattern)

@@IRONQUAD is giving RX Lost with him near or far according to friends is defective...

I also have the problem that the transmitter does not connect to the receiver. The receiver's led will flash continuously which means it is searching for the transmitter. If the receiver would find a transmitter, the led would light up continuously. however, that doesn't happen. I'm desperate too. Can someone help?

@@deni9091 If you have the same FW and flashed everything correctly, then you might have a defective RX.

You need to pick a UART (set of RX & TX) on your FC and solder the receiver to it. Please thoroughly watch from 05:42

This may be a wiring issue? The painless way is to contact Jumper RC's support to see if they have a solution.

Yes, it is the same if you are planning to bind using "binding phrase"

@@IRONQUAD binding phrase?

When updating the TX, you will have to choose the other selection that the video covers.

It should have been included in the T-Pro TX packaging. Please double check the case it came with as it is usually located on the bottom of the case.

@@IRONQUAD is there anything else I could use

@@eliteskyvisuals you may need to contact Jumper directly and see if they can send you one

@@IRONQUAD there’s no way to work around it? Do you have any extras I could buy?

yes but you will need to add a lua script for ELRS

@@IRONQUAD thanks

There are several determining factors with interference, which can affect the range. (other equipment transmitting 2.4GHz like WiFi routers or objects like trees, buildings, etc.) So there is not a simple answer to your question as your location, where you you are operating, and where you are flying/driving will all determine the range.

@@IRONQUAD How far could you get? As a comparison for my environment, my flysky receiver goes around 400m.

@@lilshlongofficial6657 kzfaq.info/get/bejne/mNWCopBkmazXoI0.html&ab_channel=GalKremer

did you select the "internalelrs" box before your flashed the fw?

@@IRONQUAD hahah yup I forgot Thanks all working now goes super far at 500mw one of my receivers has a green light just stays on will not do anything straight out of box

I would check the TX/RX signal wires to see if they are soldered correctly (TX goes to RX, vise versa) Then double check the BF settings (Ports: Serial RX, Receiver: CRSF) If everything checks out, then the port you are using currently might be set up doing multiple different functions so I'll try to use another port to see if it works.

@@IRONQUAD thanks for the reply! I would normally look into that if this was a build. If I bind to the tinywhoop with my TX16s everything works fine. But when I disconnect and connect the T-Pro ELRS 1W I have, I get nothing. So I feel like I’m missing something in relation to the T-Pro…

@@darrylmeans725 I think it is the FW. I believe the T-Pro FW does not match the receiver.

@@IRONQUAD I tried loading 2.5.1 because that’s what I have on my other radio and have put all the rx to… but maybe I loaded it incorrectly. I may need to try re-flashing it. To make sure I didn’t invert or anything.

@@darrylmeans725 Also, if you have used the bind phrase, the same exact phrase has to be on all your receivers and tx

can you please elaborate on your issue? I'm not following...

@@IRONQUAD how do you bind the radio to the module,iv got the module flashed now but I don't know what to do next

@@lauster2789 did you flash the receiver? If you used the "bind phrase" method like in this video, it will automatically bind.

Because I'm a nice guy, go back and re-watch from 2:34 :) Thank you for your interest

@@IRONQUAD Very funny, I'm not subbing. The actual binding is easier than I thought, turn on the radio, go into binding setting in the module, turn on the rx, then confirm on the tx module to bind. There is button on the RX but its not to be pressed, after 10s the rx enters wifi mode and wont bind (incredibly dumb).

no, it can work with other nano bays

@@IRONQUAD Should the screen light up after turning on the remote control? I have a radiomaster pocket remote control, and when I turn on the remote control, the transmitter does not turn on

@@Pasue_x Make sure the external module is turned on and turn off the internal to save battery power. Check out this video: kzfaq.info/get/bejne/gZmFd7yHv57JfnU.html (Only watch from 00:56 to 1:23)

@@Pasue_xPlease check my previous comment. If it you have done that, then it might be defective.