Bing 54 Carburetor Synchronization on Rotax two stroke aircraft engines.

Рет қаралды 38,981

7 жыл бұрын

www.ultralightflyer.com - Bing 54 Carburetor Synchronization on Rotax two stroke aircraft engines. A process for setting up dual Bing 54 carbs on a Rotax 503, 532, 582 and 618 Rotax two stroke engine.
www.sportaviationmagazine.com Video and Audio content is Copyright © Sport Aviation Magazine. This video and audio material may not be reproduced in any form without written permission.
Help support Sport Aviation Magazine by subscribing to our PAID subscription video magazine at www.sportaviationmagazine.com
Thank You for your continued support!
RELATED SEARCH TERMS:
experimental aircraft, experimental amateurbuilt aircraft video, homebuilt aircraft, homebuilt aircraft kits, home built aircraft, homebuilt aircraft plans, sport aircraft, light sport aircraft, light sport aircraft kits, light sport aircraft for sale, light sport aircraft manufacturers, sport planes,sport aircraft, light sport planes, Light-sport Aircraft (Aircraft Type), Flying (Magazine),
TAGS:
Bing 54, Bing 54 Carburetor, Bing Carb, Rotax Bing Carb
www.ultralightflyer.com - Bing 54 Carburetor Synchronization on Rotax two stroke aircraft engines.
• Bing 54 Carburetor Syn...

Пікірлер: 20

@me109av8r 7 жыл бұрын

Thanks for posting this. Very useful!

@noppolsomphanphae 6 жыл бұрын

Thanks for the knowledge.

@johnspinelli6170 3 жыл бұрын

Thanks

@MrHanowski 5 жыл бұрын

Nice video, thank you. Wondering about setting with vacuum gauges? A friend did this and found that the carb slides were physically set differently afterwards. He claims smooth operation. Which method is preferred and more accurate?

@ultralightnews 5 жыл бұрын

I have used both and prefer this method, no equipment to purchase or set up. The Ultralight Flyer

@demusch 7 жыл бұрын

No vacuum measurement?

@Coughtry Жыл бұрын

You really should use a vacuum carb balancing meter to properly balance the two. The 4 bank Mercury tool I’ve found is the most accurate.

@vinataba22 2 жыл бұрын

Hi, thank you for the detaild explanation. On my 503 there is one more screw for the Fuel/Air Mixture. Can you by any chance tell me what the factory setting on these is? So lets say i turn them in completly, how many turns to screw back out? Thank you :)

@ultralightnews 2 жыл бұрын

www.ultralightnews.com/enginemaintenance/bingcarbtuning.htm www.ultralightnews.ca/bing/bingjetchart.html

@thecottonpatch80 3 жыл бұрын

How high should the slide be when at full throttle? Mine seem like there to high but were in sync

@ultralightnews 3 жыл бұрын

It should be completely clear - when seen from the air filter side.

@canofpulp 3 жыл бұрын

My 582 runs rough below 2900rpm. It's a fresh rebuild. I think it could be the prop but I thought it would get worse with higher rpm.

@ultralightnews 3 жыл бұрын

Check to make sure your needle is BELOW the white plastic cup, in your carbs.

@canofpulp 3 жыл бұрын

@@ultralightnews That's not it. I just checked and it is assembled correctly. I wonder if I would be the props resonant frequency with that gearbox and engine

@jackryan152 5 жыл бұрын

The process for Hirth 3203 with the delorto carbs are just about the same

@michaelbartlett1589 3 жыл бұрын

I had a single carb duel ignition and I upgraded to a duel carb. I have had issues like crazy getting it started. After I can finally get it started the RPMs are way too low. Like 800. If I give it gas it dies. Eventually it revs up and sounds normal. I can give it gas and it acts normal. After warming up fully it will idle like normal around 1800-2000. Any idea why this is happening? I have re jetted for my altitude and even replaced my needle jet. Nothing seems to help.

@ultralightnews 3 жыл бұрын

www.ultralightnews.ca/bdrive/rotax-a-gear-box-and-rotax-b-gear-reduction-drive-updates.html

@michaelbartlett1589 3 жыл бұрын

Light Sport and Ultralight Flyer thanks for the info. With this engine only having 20 hours on it I wouldn’t think this would be the issue in this situation. Any other suggestions on the carb side of things?

@ultralightnews 3 жыл бұрын

www.ultralightnews.ca/bing/bingcarbtuning.html www.ultralightnews.ca/bing/bingcarbdisassemblytip.html