I am following you're instructions to the LETTER and it WILL NOT bind. I am using the Blade MLP6DSM TX. I bought this used but NIB S2 blade RTF.

Could you all do a video on Drift calibration for the Nano S2?

should this also work with blade nano s3 and DX6? I seem to be just stuck in beginner mode when i follow these instructions...

Are you able to invert it when using the stock transmitter that comes with the RTF model?

Hi! Last week a got a new Nano S3 together with a new Spektrum DXS. The DXS came with Software 1.24. I did an upgrade to the currently newest version 1.30. Before upgrading it has been possible to fly only in "green" mode. It was not possible to change modes with one of the switches. Helicopter battery has not been reported to the DXS. After upgrading DXS to 1.30 there still is no switching possible through the modes. Telemetry still is not sent to the DXS. Unfortunately the Nano S3 remains in "blue" mode. Only by pressing and holding the BIND-button it goes in "green" - mode. The throttle is very agressive and almost unusable. The DXS is on "heli"- mode. Means that the LEDs are orange. I have changed DXS to the different "blue" - airplane modes and back to the only "heli"- mode with exists. I have bound it afterwards serveral times. All switch positions in 0- position. The binding reaction of the Nano is like it is shown in the video as it is with Computer Transmitters. What is going wrong? Yours Holger PS: Besides that I am very disappointed about the DXS. It has no display. I hoped that it would be possbile to do programming through PC-Software "Spektrum Pogrammer - Beta". With DXS only software- upgrades can be done. Nothing else.

For binding with MLP6DSM the manual doesn't mention holding in the left stick (like a button) as explained here, but says to turn transmitter on with panic button down. Please advise.

Bought an RTF Nano 3S. Why is the LED light on my heli rapidly blinking in green? Had a small crash, heli still in tact and looks OK, but it won't react to the MLP any more... can't manage to re-bind the heli again.

Got flight mode to work, for anyone struggling on a dx8 make sure u put the settings for correct generation and just follow instruction manual settings. For 3 d flips just a little input on the cyclic works great. I cannot get mine to hold the bond and have to bind it every time I fly it. Very very good fun tho

Just tried to import the GPX to my phone. Message Failed file may be empty.

I cant get my mlp6dsm to bind to my torrent 110, any help would be amazing!! Please and thank you

Why not fox the S3 manual and include the tip about smash plate travel after binding?

Well it's a bit difficult. When I press down on the right stick it elevated my chopper. Mode 2 it was blowing the other way. I just bought it today.

How to you set up and activate Panic Recovery using a computer transmitter?For example a DX6i?

Will the dx6i be able to get into stunt mode? I can fly with the dx6i but u can't figure out how to get Into stunt mode. Should I just buy the newest remote? Maybe the dx6i is outdated? Please help

Yeah I've been following these steps for some time and I still can't get my stable z mode to work. I'm guessing that's why they have version S3. I'm using an ix12 and everytime I bind it, I don't have any throttle with my f mode switch in pos 0.

It lasted 5 aeconds with me on the controls. Old DX7s. pilot error, went straight to the moon 🌙. It was a nice looking tiny Heli. Well, back to 5 inch quads.

I crashed and don't know if I blew the tail rotor motor. It will only spin in 1 direction. I can replace it but if I want to buy another s2 can I bind it to the ready to fly radio?

I really want a brushless motor for my( Blade Nano S2 ) but cant find one they made them for the ( ncpx ) and the ( npcs ) but where's the brushless motor upgrade for the Blade Nano S2 and how do I get it?

can these bind to a tx16s?

Have Dx8 transmitter. Heli flies for a couple of flights then refuses to fly. Either starts to fly then on increasing throttle motor cuts out. Or sometimes simply spins around on the ground!

Is this Blade nano S2 compatible with Spektrum SPM6755 DX6 Transmitter ?

Hello, how can I check whether the SAFE function is working properly? When in active SAFE mode, the LED lights up blue or orange? I 'm using the DX6. Thanks Uwe

Oh thnx sooooo much

Thank u

Do you have to bind it everytime you want to fly?

Anyone bind this with a Jumper Lite TX/OpenTX?

Can I bind my nano 2 with my dxs ?

permanent quarantine for customer service . that s the new way

My dang computer keeps giving me crap and can't download spektrum program and it's a brand new hp laptop...I'm about frustrated and ready to break another laptop because of this crap

Flight mode does nothing on my dx8

would LOVE to see one function with a DX9 remote without going to the skies in IU2 , and since phone support has been TERMINATED , you will have to be content with the latency of emails , and obscure information . just crumbling as a company with zero effort to right things , bummer .