You should do a video where you take Andrew’s car away when he’s working; and replace the headlights.🔥🔥🙏🏻👌🏻👏🏻
@BREW2LFOXBODY3 жыл бұрын
Lmao! 😂🤣 y’all are brutal
@darylfitzgerald13273 жыл бұрын
😂😂😂,. 💯🦊
@darylfitzgerald13273 жыл бұрын
This is a excellent tutorial,. My 7 up fox recently had a lobotomy. I actually came on the channel to find one of your face idol reset videos that I used two years back. How exciting it was to find this new video. . I'm so pumped that you redid this video when you did. ... 💯🇺🇲
@terryk1593 жыл бұрын
Ty Brewt. You always do stay on the basics of keeping these cars running right and you're all about it. You are certainly given me the ability to face any issues upcoming I appreciate you man
@BREW2LFOXBODY3 жыл бұрын
We tend to forget the basics over time with all this new technology these days. But it’s crazy how much can be accomplished if we slow down and learn our cars. These old systems weren’t really that bad and have several work arounds that still work today.
@chrislogan50862 жыл бұрын
FACTS
@Neomustangs3 жыл бұрын
Such classic knowledge that needs to be revisited often. Good Job Brew.
@BREW2LFOXBODY3 жыл бұрын
Thanks bro!
@Riffs_Garage3 жыл бұрын
When doing a base idle reset you really need to unplug the tps, iac and spout connector. Set the idle screw to where the engine is barely idling around 400-500 rpm. Then plug everything back in. The reason you need to unplug everything is because all of those things will try to correct the idle as you turn the idle screw off they are plugged in.
@ayyy9017 Жыл бұрын
The tps too?
@Riffs_Garage Жыл бұрын
@ayyy9017 yes. A base idle reset is basically setting the pure mechanical idle of the engine without any electronic control.
@ayyy9017 Жыл бұрын
@@Riffs_Garage would you recommend disconnecting everything and then setting timing, tb screw etc and then turning the car off and plugging everything in afterwards?
@Riffs_Garage Жыл бұрын
@ayyy9017 I would set the idle first then plug everything back up and make sure the engine idles up where it's supposed to be. Then unplug the spout connector and set your base timing
@hotrodray68023 жыл бұрын
Thank you for actually telling the ECU acceptable TPS spread.
@jamesgeorge48743 жыл бұрын
EEC3. The dealer had a diagnostic machine called the SBDS. It was the size of an arcade game, like the one you put quarters in. The veteran taught me exactly the same things, back in the late 90's, a DVOM, and dial back timing light. .51 to .99 was acceptable tps voltage. Occasionally a dead spot in egr valve position sensor would cause an errant high idle too, we would nick a little off the sensor pintle on the grinder and let it relearn.
@justanothajoe3 жыл бұрын
Excellent distribution of knowledge. The earlier Fox's were a nightmare to get the idle to act right. I've got about 1,300$ in tune now and my car (heavily modified) will sometimes fall on it's face when I'm on the highway and take an exit. I downshift and use the brakes. It dies here quite often. I'll try your wisdom and I hope it acts right!
@BREW2LFOXBODY3 жыл бұрын
It’s worth a try!
@sav22rem223 жыл бұрын
Very well done video. This is how I’ve fought my idle for a while now. I’ve got it exactly where I want it
@STXDrIvEr985443 жыл бұрын
Your first video helped me out so much, and man that couldn't be further from the truth when it comes to cammed cars. Mine has the TFS 1 in it and I finally found that sweet spot around 800rpm or so, anything below that it starts throwing a damn fit and surging and running like shit.
@BREW2LFOXBODY3 жыл бұрын
Glad the video helped brother! And you’re exactly right!
@terryk1593 жыл бұрын
My trick flow is idling at 1000. it chops every tree in town. It's so sweet though and it's running so good. I'm glad you're able to have a sweet spot ith yours
@whitefoxpaul1993 жыл бұрын
Nice little covert operation good video I've gone back to your older ones that helped me so much
@scottyfiveo13 жыл бұрын
You're a brave man. Going to pick up the BLACK WIDOW MOBILE in the heart of SPIDER COUNTRY!!!!!
@billanderson79802 жыл бұрын
By far one of the best DIY for Foxbody owners and so knowledgeable
@triksracingify3 жыл бұрын
I used to do this to my mustang but it's been a while helped me remember the .999 for the TPS sensor thanks I was about to look this procedure up
@justanjustan96242 жыл бұрын
I just got my first Fox back in July (an '89 GT vert). The way Andrew's idles when you first adjusted it on the throttle body at 2:26 is exactly what mine does right now, especially during coldstarts (and that's AFTER it spends about two minutes bucking like it wants to shut off). All of this information is really helpful!
@dennislacy51053 жыл бұрын
It’s a very important point that with an aftermarket cam the idle speed must be raised above factory. How much is necessary will depend on how aggressive the cam is. Years ago my best friend and I straightened out the idle on countless modified Mustangs that we met around town. The common denominator was that the owner/builder was trying to idle the engine too low and they had the usual surging idle. Up and down, up and down. What few people realize is that when you try to idle a more aggressive camshaft too low is that it creates “intake reversion” which is a reverse pulse through the intake tract all the way out to the air filter. This is because more aggressive cams have more valve overlap, the amount of time both valves are open at the same time as the exhaust stroke is ending and the intake stroke is simultaneously beginning. Imagine a situation where your MAF is reading incoming air one moment then suddenly not the next moment like someone turning a light switch on and off rapidly and continuously. So one moment the computer is seeing air flow from the MAF then it’s not. The computers reaction is to raise and lower the ignition timing to match and that is where you get the surging idle. Sometimes the surging is consistent and other times it’s a runaway situation where the difference between high and low grows wider and wider to the point where the low is so low the engine stalls. If you put a timing light on while the surging is happening you can watch it shoot up and down, up and down, up and down. All these people would put those goofy adjustable spacers under the IAC when the surging idle has nothing to do with the IAC. It’s all because the ignition timing is going advance then retard because of intake reversion. You have to increase the idle speed enough to get passed the reversion to where you’re getting a consistent, continuous intake reading from the MAF and then like magic the engine will idle steadily. We typically found 850-950rpm to be the happy range depending on the cam used. All these people thought we were magicians when in reality we just understood how a more aggressive cam changes the dynamics of an engine. Intake reversion can also play hell with idle stability on carbureted engines.
@wtfdatsgay2 жыл бұрын
I'm going to try this tomorrow I'm having a terrible trouble with my idle.
@mybannerisbetterthanyours2 жыл бұрын
@@wtfdatsgay what fixed yours?? mine has dropped to 200-300 rpms 😳😳
@GearHead7043 жыл бұрын
This was some classic Brew2L stuff plus it was on my favorite car on the channel. Great stuff!
@BudzyFoxMX5 Жыл бұрын
Thanks for this video. I just bought a 1990 SSP in Colorado and drove it home to Atlanta. Thing bucked hard when just trying to stay at a steady speed, I always had to accelerate or decelerate for it run "smooth". Also, idles at 500 when hot (has an unknown aftermarket cam). Found two massive vacuum leaks in the lower intake gaskets. Going to change those, then follow your steps in this video. Your content has been gold to me since I've never owned a Foxbody before.
@MrLaddy583 жыл бұрын
This video is a great example of why I’m subscribed. I love your videos, but you sir are a well of knowledge for the Fox Body community, and I would love to see more vids like this. You have an excellent way of explaining things.
@CombsTowerProductions3 жыл бұрын
Man when you show Andrew’s engine bay and then show them engine bay in the retro fox, it’s so clean compared to Andrew’s. God Damn!
@mikeskipworth94643 жыл бұрын
You’re a cool ass dad, man.
@BREW2LFOXBODY3 жыл бұрын
🙌
@feellnfroggy3 жыл бұрын
Timing without spout should be at 10* from factory, it’s the default when spout is removed. And once plugged in it advances to where it needs to be. This save a bunch a time.
@89gt5.03 жыл бұрын
I love this channel.
@BREW2LFOXBODY3 жыл бұрын
🙌
@pauls48612 ай бұрын
Very Good Video! Helped a lot and after watching a few times and made Base Idle reset easy. Do you have a video on part throttle cruise jumping or bucking? Car is running good but with throttle at a steady spot, it starts bucking some unless rpm's/throttle trending up or down with pedal. Was going to check plugs and fuel pressure. No check light now after sending computer off and fixing few other items related to codes.
@paulhudgins51203 жыл бұрын
Always teaching the basics to figure out what adjustments to make for each component for what they change, always informative. When you got Andrew's car were thinking about bombing for spiders again?
@90foxmustangguy493 жыл бұрын
Great video, would you happen to be able to do one for Carburetors? How to adjust your carb for idle? Have an 85 GT new to learning about Carb cars
@BREW2LFOXBODY3 жыл бұрын
It’s been a while but I’m sure we could do something on Andrew’s carb fox
@90foxmustangguy493 жыл бұрын
@@BREW2LFOXBODY thanks huge fan
@galaxie77533 жыл бұрын
Check out Thunderhead289 on KZfaq. He specializes in carburetors and how to set them up.
@NicLaRochelle2 жыл бұрын
Perfect explanation, very thorough. Thank you for the extra advice when running a cam, helps a lot. 👍
@trailerpark1873 жыл бұрын
I love how clean under the hood is on the retro fox
@TheCarJunky12 жыл бұрын
Thank you for this video! Gonna do this to my fox! Your videos are always awesome! Thank you for helping keep these cars alive!
@johndoe-zb8bm3 жыл бұрын
Dropping knowledge as usual!👈💯🔥
@DakhilB6 күн бұрын
Thanks man, I needed this video....
@Ttop_Thomas3 жыл бұрын
After you take it again and replace those headlights @Kevin wines suggested you do, you should detail the engine bay for him! LoL
@lochnessfox34413 жыл бұрын
Andrew has a great little notch there don’t he?
@BREW2LFOXBODY3 жыл бұрын
He does 👌
@89gt5.05 ай бұрын
2 years later and after modifying my fox I’d like to this video done again with a h.c.i fox.
@Yobbo_91gt Жыл бұрын
The bucking is what I’m having driving around the neighborhood. I didn’t know how to put it in words. Resetting the IAC as shown may help? I have installed E cam, heads, lifters, injectors, MAF, cold air intake, timing chain new IAC.
@travisevans75023 жыл бұрын
my pcv valve was bad and it caused me all kinds of grief with idle realized it was bad and replaced it idles perfect now I could get it to idle for little bit think I finally got it go for a drive and it would start acting up again it was so frustrating the old saying if you shake the pcv and it rattles it's good not true
@richardmigliacci760128 күн бұрын
I have a fresh 347, steeda 18 cam, e street heads, Edelbrock proformer intake,msd des, 30lb injectors matching MAF, 70mm throttle body, it runs but every minute or so it surge's
@klokkerhaug1 Жыл бұрын
I have a Trick Flow top end kit. I have struggeled with idle and stalling. I just got it to start and idle nice, did the base idle reset. I had no difference in rpm`s when unplugging / plugging the IAC. It idles good around 750-800, timing 12-13 and TPS 0,98. But if i rev it and let go of gas it stalls, wont even surge. Also when releasing clutch it stalls. It sometimes struggles with start up and idling but ends up idling perfect, but stalls if i rev it and let go of gas🤷♂🤷♂🤷♂🤷♂
@mathewshackelford80372 жыл бұрын
I just did this with a new IAC. it was idling way high so I unplugged the IAC, it dropped down where it should be and when I cut the car off, plugged the IAC back in and restarted it, the idle shot way up. Back to the drawing board....
@vicvasquez85544 ай бұрын
hey love ur videos been very helpful. but im currently stumpped and been tryna find a video with my problem but havnt. so in my situation i have a 87 foxbody but car wont let me try to do timing with the spout connector removed. i even have it running and pull it out and just shuts off . been frustrating. the owner before me has a mega squirt ecm. i dunno if its cuz of that
@chrislogan50862 жыл бұрын
Hell... 😏Thats bout what my ish sounds like after my green ass starts tryna pretend like i kno what im doing!! .🤦🏼♂️ LMAO fr! Thats why i come here for fxbdy wisdom!! Luv tha ch. nvr miss a vid and jus like right now, i end up rewatching most videos multiple times... I Watch the hell outta them shitz
@chrisneal39092 жыл бұрын
I have a 88Tbird stock 5.0 EFI 5spd swap, 99 Gt axle and front hubs. I have these idle problems. Thanks for video.
@tomborders60032 жыл бұрын
Do you set tps voltage with idle screw all the way out? Or use the idle screw to achieve your .98 volts?
@EliLee9183 жыл бұрын
😂 your gonna have a base idle reset series
@BREW2LFOXBODY3 жыл бұрын
Looks that way lol
@aaronschulte69148 ай бұрын
Great Video...a few questions. Does the car need to be at operating temp? What are your thoughts on aftermarket throttle bodies without the small hole in the throttle blade. I'm running a 70mm and it doesn't have a hole where as the factory ones do.
@brighton19313 жыл бұрын
I have one screwed up Foxbody, I wont lie.
@BREW2LFOXBODY3 жыл бұрын
😂 we’ve all been there brother
@joelbravick95458 ай бұрын
This is great info, thank you for putting this out there. I have a 95 with the 5.0 h.o and it supposedly has a e303 cam but is doing the idle surge and feels pretty sluggish, i would like to check the timing but the distributor is actually stuck. What would you recommend to get it unstuck?
@Bustedknucklegarage832 ай бұрын
Man I could really use your help with my 89 gt 5.0 I'm redoing most of the car but there's a timing issue and a no start no fuel pump when hot
@Adam-pd3fc5 сағат бұрын
What if idles fine 700-800 on startup but after it warms up idle goes to 1100-1200?
@zlowe36432 жыл бұрын
My fox is on jack stands is that good?
@TheTDude243 жыл бұрын
I have a quick question. I can not get my tps below 4 volts for some reason. I'm not sure if it's something I have done or what. The timing is set right so I'm lost.
@automotiveaddiction4283 жыл бұрын
Anyone know the secret to get a seat belt to retract..my kid pulled it out to the max...not looking forward to pulling of the moldings from the door to the hatch
@paganpoetprophet64414 ай бұрын
Take Andrew's fox and put new oversized tires and brakes disc all four
@timw27552 жыл бұрын
Love the way Andrews Tires look. I have similar Eagle 4 bolt rims and want that exact look. What size are Andrews tires front and back and has he removed or flipped his quad shocks?
@justenblankenship61232 жыл бұрын
I’m having idle problems with my 95. Iac unplugged it idles rough and sounds like it’s cammed. Which guy i got it from said it had work done. Iac plugged in it shoots up to 1,500 rpm at idle. I’ve tried everything Ik. It also smells like it’s burning very rich and smokes when u romp on gas
@paulkendall343 жыл бұрын
You should never touch the screw on the throtalbody!!! Now its really messed up. Throtalbodys are adjusted on light table and now you go turn it so if u set it at 98 tps its going to be off because u turned the screw and of course its idle is to fast.. recalibrate lol... ok
@95turbostang213 жыл бұрын
The same way the factory idle reset is done I wonder if it makes any difference if you do it when running a Terminator X I'm going to have to give it a try and see
@BREW2LFOXBODY3 жыл бұрын
It doesn’t work with the TX like that. Just do the TPS setup and you’re good to go. Throttle position can definitely help though
@davidpound23757 ай бұрын
This might be a dumb question but I just went carb on my 87 lx I’m running a 6al box and a hei dis. What wires on the harness can I get rid of. I was keep ac I know the alt and I’m keeping the oil pressure and coolet temp
@theodoredorward62452 ай бұрын
Hey, you know about all these threads on Facebook and all that stuff not getting real answers is there anyway I can throw you a picture and see if I’m completely screwed 1989 Mustang GT 5 L little bit of an accident
@jacobklessens5959 Жыл бұрын
Love the videos man! I have a 93 fox. What would cause my RPMs to hang up around 1500 when i let off the gas. Then if I blip the throttle, it returns to normal?
@kylesplumbing60022 жыл бұрын
I need help with my idle issue that just started on my 1990 gt, it will idle high around 1200 and sometimes up to 2000-2500. I’ve set timing, factory set idle. When it idles high, I can turn the car off and re start it and it will idle back down again. Replaced Iac and tps with no change.
@boatdoctor1002 жыл бұрын
Great video.. I tried setting the the base idle and now the engine won't start. Any suggestions on what could have happened? thanks
@galaxie77533 жыл бұрын
Thank you for that information. I have done the base idle reset before, but I never shut off the engine before reconnecting the IAC. I am curious though, if I connect the IAC while the engine is running, will shutting it down and restarting it do the same thing, or does it need to be disconnected when it is shut down? Also, my car seems to be running really rich. I am running a basically stock rebuilt 1986 HO with an A9P (automatic) in my 1967 Galaxie 500. The only mods I have from the Mustang are long tube headers and the smog pump and cats removed. It seems to run great, but really rich. Any help would be appreciated.
@cuckstianityisforcowards-rb9xi Жыл бұрын
You need to space the O2 sensor to trick the readings for the computer.
@treytongilbert54282 жыл бұрын
Hey, thank you for the video. I replace the engine and basically everything. Recently put a new throttle body on followed this video. Idle is pretty good but took it out for a rip got home and the idle bogged down and the car died, I started it gave it a rev and it the idle caught itself. Does this sound like the computer is just re learning everything?
@joshualymer65682 жыл бұрын
Hey man great video will this procedure be the same for a 90 F250 460 EFI motor thank you
@damianhughes70342 жыл бұрын
I've been having issues with the iac valve I've replaced it 3 times even got the original part.number Motorcraft from summit racing runs great for a month then dies at cold start and will stay running when warmed up any help is greatly appreciated
@damianhughes70342 жыл бұрын
Thank you for the video learned something new
@jakew2350 Жыл бұрын
Can I do this on a car that has a tune? My car idles and runs great but has idle hang when I rev it. I’ve tried motor craft and aftermarket iac and no help
@ScaleModelCarBuilder2 жыл бұрын
New subscriber here, I noticed you have done these on the 5spd cars a couple times. Is this going to be the same for AOD cars? I have a random high idle (hot or cold) and will stop if the engine is turned off then started back up and looking into it this spring.
@jumexvhr Жыл бұрын
Very helpful thanks for the video
@djdev30773 жыл бұрын
Watch that fan blade,work from the left or right side,
@theodoredorward62452 ай бұрын
I don’t wanna bother anybody or take their time. I just want some truth to be told to me. I think I already know what’s the answer is, but can I shoot you guys couple of pictures? The car beautiful it’s not it’s worth trying to save. It’s just I don’t quite know, it’s about 85% OK but you know with Foxbody 🦊🦊 it takes 5% of screw one, but I’m not quite sure with this in particular situation. I can’t get a straight answer out to anybody.
@mcar4543 жыл бұрын
Can you do a base idle reset if the car isn’t fully warmed up?
@BREW2LFOXBODY3 жыл бұрын
If at all possible get it to operating temp first.
@mcar4543 жыл бұрын
@@BREW2LFOXBODY gotcha, trying to fix the bugs in my hci fox after installing a chip. Appreciate all of your videos
@TMZTucson2 жыл бұрын
If I have a sound system, should I unplug my power wire running from the amplifiers to the battery when running the car with no load?
@meyerspreston2 жыл бұрын
Hey. Long time watcher. Looking to building a garage. I was wondering what the dimensions of the building is?
@BREW2LFOXBODY2 жыл бұрын
Thanks! It’s a 30x30
@TekMan05 Жыл бұрын
Would the basics of this still apply to me having a cammed 5.0 in an Explorer application. Major difference being I have ignition coil packs instead of a distributor?
@gabymaldo2424 Жыл бұрын
Hey bro,i just bought a fox body and it has a coil pack, it's the same procedure???
@whatwouldjoshdo1131 Жыл бұрын
What is the best wide band sensor kit to use with the mega squirt?
@joshuaflaherty28803 жыл бұрын
brew, what socket size are you using on the throttle body screw? im pretty sure my screw is either broken or somewhat different. have never been able to mess with it because it doesn't look like an actual screw, just the threads basically. I got a bcam so its hard enough to make it idle without warming it up a little
@BREW2LFOXBODY3 жыл бұрын
Mine is a 10mm but if it’s aftermarket it more than likely has a Allen socket at the end of the stud.
@joshuaflaherty28803 жыл бұрын
@@BREW2LFOXBODY just checked, I think it use to be a screw, no way its an allen. things been rusted and snapped at the head, i'll have to find a way to get it out and replace. Thanks Brew, great new base idle vid!
@gtcobras9 ай бұрын
Would this apply to a 1995 mustang with stock computer and a foxbody throttle body set up?
@sn95_capo32 Жыл бұрын
How much timing should I put on a 95 mustang gt with full exhaust and cobra lower and upper?
@stenjohnson6149 Жыл бұрын
I’ve done the base idle but hot start is💩 with surging that sometimes kills the engine. It was suggested that I start the car with the alternator disconnected and see. Unplugged the alternator and it starts right up and idles like BUTTER! Plugged it back in… surging! Alternator or wiring? Opinions please and thank you! Sten
@Cristoolit5 ай бұрын
Did you figure this out
@isaiahtucker48 Жыл бұрын
I need to bring my car to you lol
@PplFox3 жыл бұрын
Can you please Polish them Headlights!! 😳
@BREW2LFOXBODY3 жыл бұрын
He needs to buy some! I ain’t working on them 😂😳
@Scrapla1 Жыл бұрын
My car sat for years and I got it started but it idles super high around 2k. Could this be the issue or maybe sticking TB or IAC?
@jerrypuckett67332 жыл бұрын
Nice. Helpful.
@manuelacuna63782 жыл бұрын
Good stuff!!!
@dannyblea Жыл бұрын
My biggest issues is now that I've done the Idle Reset, The Spout doesn't seem to do anything. When I tune the car to 12-14º it runs just ok. I noticed my Timing does not move with or without the spout connected. RPMS doe not move when it's connected or removed. I've tried a jump wire and checked volts on the spout and everything seem to work. Timing does not move with or without spout. Help. 🙏🏼
@dannyblea Жыл бұрын
It was the computer issue for those that might be experiencing the same issue.
@cuckstianityisforcowards-rb9xi Жыл бұрын
Send me all the info on your car and I could try and help. That is if you're still needing some help, if you got it then right on man. 💪🏻 Let me know either way, cheers! 🍻
@jordanrobinson70122 жыл бұрын
my car has a b cam and the rpms fluctuate from 800 to 1000 when at idle. is that normal?
@Mattys91gt2 жыл бұрын
what can I do without a timing gun to set mine
@kennyp49673 жыл бұрын
It needs a terminator x
@paulkendall343 жыл бұрын
Its already dark outside took all day and night for you to halfway keep it running. I bet wot is all messed up.
@SantiSpeed111 ай бұрын
Hey Brew, I’ve got an IAC that sits at 5-6V when running, is that normal?
@ryan-pn3vz2 жыл бұрын
Same procedure for 1994 5.0 ?
@enriquetrevino7815 Жыл бұрын
Would a Power Probe be ok to use ?
@FailFunnieTV3 жыл бұрын
Does this reset also apply to 94 to 95 Mustang gt ?
@zerofoxgiven893 жыл бұрын
What would cause it to surge at idle?
@BREW2LFOXBODY3 жыл бұрын
Typically timing or throttle adjustment is what I’ve seen cause surging over the years. But other factors could also be causing issues as well. Bad sensors or IAC motor
@zerofoxgiven893 жыл бұрын
@@BREW2LFOXBODY still does it if I unplug the iac
@jferr2000us2 жыл бұрын
does a base idle reset effect your tune?
@cloucks10033 жыл бұрын
Straight up cloak and dagger shit!
@BREW2LFOXBODY3 жыл бұрын
I know right!
@paulkendall343 жыл бұрын
Watch the accufab video on KZfaq about turning the screw. Big no no!!!!
@blacknotchNJ2 жыл бұрын
I only seem to be able to get .20 on my TPS when I check the voltage. KOEO... and from eyeballing it it seems impossible to get even close to any acceptable ranges.
@BREW2LFOXBODY2 жыл бұрын
It’s possible that the throttle blade needs to be adjusted and then perform a base idle reset.
@blacknotchNJ2 жыл бұрын
If i adjust the idle screw will it be idling way high? When i manually open the throttle I see it change accordingly... the preload you speak of putting on the TPS, is it a very small amount?
@BREW2LFOXBODY2 жыл бұрын
Unplug the iac and adjust the throttle so that it idles around 600-700 or so. Then switch the car off, plug in the iac again and start the car back up. You should be about right there.
@blacknotchNJ2 жыл бұрын
Has an anderson n41 cam, I've had trouble getting it to be happy below 850-ish. Am I just over thinking the TPS stuff?
@BREW2LFOXBODY2 жыл бұрын
It’s going to want to idle around 850 to 900 more than likely. So set your idle around 700-750 with the iac unplugged and you should be good. Then just make sure the tps is between.5 and 1 volt