In this video I am replacing clutch, clutch pressure plate and clutch release bearing.
Пікірлер: 29
@arthurbairner79533 ай бұрын
You are a very professional mechanic and produce an excellent video. Thank you.
@EverydayValuedMechanic2 ай бұрын
Thank you, much appreciated trying my best!
@tomjenner68182 ай бұрын
Top stuff mate. Engine blew up on my 118d. So thought i’ll do it myself and use the 120d more powerful engine. Taken the engine out but wondered how to swap my gearbox. Just a screwdriver 😂. Given me a lot more confidence and reckon i’ll do it after work tomorrow
@EverydayValuedMechanic2 ай бұрын
Thanks, same reason I stay away from engine upscale because of the gearbox mis-match, but good luck with yours, some of the BMW gearbox's fix multiple engines.
@janisivanovs21637 ай бұрын
Nice job! Thanks for vid!👍
@essamsabbah40163 ай бұрын
you are the good mechainic in youtube
@EverydayValuedMechanic3 ай бұрын
Thank you!
@ndumbadavid203 күн бұрын
Thumbs up 👍 for this video
@sasindudinusha38473 ай бұрын
Great content mate
@EverydayValuedMechanic3 ай бұрын
Thanks much appreciated
@thinkoutsidethebigbox10022 ай бұрын
❤
@Muuqro5 ай бұрын
thank you Nice Video!!! How much does This Costs?
@thinkoutsidethebigbox10022 ай бұрын
Great stuff mate! I've exactly same problem with my car. Where are you based mate? I'll drive straight to your garage
@EverydayValuedMechanic2 ай бұрын
Redline Garage Loughborough, thank you!
@Growing12up3 ай бұрын
Great work keep up
@EverydayValuedMechanic3 ай бұрын
Thank you, much appreciated!
@Giancarlo-ol2mu4 ай бұрын
I have not seen the special tool used to center the entire assembly before being tightened with the wrench. The original BMW spare part incorporates a centering pin which must then be removed when all the bolts are tightened.
@EverydayValuedMechanic4 ай бұрын
Well there is multiple ways to do it, yes most of the flywheel+clutch kits comes with it, but it is not always the case, so you it oldschool, it might not be perfect but if it works then it will do.
@vicenteguerra4728Ай бұрын
Esa pieza dañada puede ocasionar vibración, reemplace en una x5 ambos soportes de cardan pero le quedo una cierta vibración !
@EverydayValuedMechanicАй бұрын
On 4 wheel drive, it is different and different things can cause vibration, if its only while stationary its worth checking all engine mounts, thanks for the comment!
@vicenteguerra4728Ай бұрын
@@EverydayValuedMechanic entiendo, revisaré soportes de motor por que efectivamente es 4x4 muchas gracias excelente vídeo !
@mangorbbos10483 ай бұрын
Are the hardydisks the same at the gearbox aswell by the diff??
@EverydayValuedMechanic3 ай бұрын
Hi, did not get the question, but if you meant propshaft bushings then yeah same on both sides!
@jamesbarratt5933 ай бұрын
Changing clutch master cylinder is a complete nasty job. FACT. I am middle of doing it.
@EverydayValuedMechanic3 ай бұрын
Yeah I bet it is, as on most cars they are, but non the less good luck and everything goes smooth with it!
@jamesbarratt5933 ай бұрын
no nothing went smooth with it at all. First I got the customer a woman talking turd. The plastic under car held by rusted screws which snap. Then the pedal system. Trying to just remove the clutch master almost worked BUT. Above theres 8mm id braided pipe which pushes down on a nipple half way along the body of clutch master cylinder. You might but I failed. Screwdriver prize it off but no space. Whole time im upside down feet on seat head rest. Head under dash. Only one arm working. Trying to hold up pedals. Push nuts on. Unplug connectors. Fit pressure pipe and retainer plus brain pin. All one hand and whilst holding the pedals fingers working doing multiple tasks. Me getting hot and irate. Then with all back in and a new feed hose going up through bulkhead waiting to be cut short to join filler bottle, I had one last thing to do. Fit the flat sensor to body of clutch master cylinder. It would not clip in. Right up high behind dash and whatever I did not click showing good fit. Took it out to old clutch master and it clicked in fine. Back to new nope. After 30 minutes in the end I took the pedals out again. Yep. Dropped them and then tried switch. Still not clicking in. Reason being pattern part. Slight difference. Then surprised by boyfriend of customer and him saying whens car gonna be finished. No hi how are you. Shit job
@EverydayValuedMechanic3 ай бұрын
@@jamesbarratt593 I feel you friend is just one of those days and cars that just don't want to play with us, nevertheless I wish you better luck in your future endowers.
@Growing12up3 ай бұрын
How much do you charge for that
@EverydayValuedMechanic3 ай бұрын
It is just over 3h labour this garage where im working charging £75 an hour.