BMW M54 DISA Valve FIXED and Upgraded!

Рет қаралды 43,724

Жыл бұрын

Need a DISA Valve or rebuild kit? I provided links for you guys below!
This DISA VALVE video has been taken from my earlier Chrisfix video
• Worlds Most Reliable B... to create a DIY guide.
**Giving this video a "Thumbs Up" really helps with the KZfaq algorithm, Thank you an advance!
**Consider Subscribing to / jamiesgarage1
--I really appreciate it!
Check out Jamie's Store!: ourwearhouse.com/collections/...
DISA valve rebuild kit for M54 3.0L: bit.ly/3yqNkZX
DISA valve rebuild kit for M54 2.5L: bit.ly/3VdUmuP
New DISA valve for M54 3.0L: bit.ly/3rCQlmm
New DISA valve for M54 2.5L: bit.ly/3ebvSSF
---As a creator stash associate, I earn from qualifying purchases.
---------------------------------------------------------------
Jamie is the Owner of Elite Motor Works in Sarasota Florida, Check out his social media in the links below:
-- TikTok: / jamiesgarage
-- Jamie’s Garage Instagram: / jamiesgarageofficial
Check out Jamie’s Shop Elite Motor Works
-- Elite Motor Works Website: www.elitemotorworks.net
-- Elite Motor Works Instagram: / elitemotorworksfl
-- Elite Motor Works Facebook: / benzandbmwrepair
-- Elite Motor Works KZfaq Channel: / benzandbmwrepair

Пікірлер: 87

@JamiesGarage1 Жыл бұрын

Guys, it’s been a crazy busy Month for me 😮‍💨 but I’m finally getting caught up and I’m excited to have several videos coming to you this month. 💪 Including the SMG to Manual conversation of my e46 m3, preparing my 335d for impact festival, installing bayoptik headlights in the e90, adjustable end links and the f80 competition seat conversion into my e90 😁 For now, here’s a quick video from the chrisfix m54 video where I rebuild a DISA valve to make it better then new! Thanks for watching 🤘BMW M54 DISA Valve FIXED and Upgraded!

@JoseGarcia-zb3ki Жыл бұрын

Would the repair kit work on a N54 2009 335i xdrive or do you know a kit for this platform? Just want to make sure my engine doesn’t get messed up if there is the same problem.

@Michal_Sobierajski Жыл бұрын

Super, że dzielisz się takimi usprawnieniami. Pozdrawiam.

@JoseGarcia-zb3ki Жыл бұрын

Nvm I being dumb the n54 doesn’t come with a DISA valve🤦🏽‍♂️ sorry bout that😅

@dennisvandegrift9085 Жыл бұрын

Great video the best I have seen so far on this repair. Do you have a link to the kit you purchased? I’m in the process of upgrading my N52 with the 3 stage and I want to rebuild both DISA valves first. Thanks for the video!

@sloppy101 6 ай бұрын

Just bought a disa intake for my non disa e90. I’m so glad I saw this before just giving it a clean and throwing it on. Im coming from the e30 to the e90 and im learning sooo much about these cars. It’s crazy how easily you can create power in these little engines

@AshtewanPhotoVideo Жыл бұрын

Thank you for doing this. Good repair videos are rare and you do great cars.

@YZFMANIAC08 11 ай бұрын

Just ordered my repair set, looks pretty straight forward 👍🏻

@zimmy700 Жыл бұрын

Well done Jamie 👏🏻

@ricky_ricardo Жыл бұрын

Thank you this was very well explained. Will def be doing this to my low mileage e46 just to be safe

@SniperFVG Жыл бұрын

Thanks from France ... very good tutorial !

@hooshangmaster Жыл бұрын

heh this is pretty useful also discovered a new paranoia since i didn't know the pin can enter your engine.

@JamiesGarage1 Жыл бұрын

be scared, very scared! lol

@oldjarhead1125 Жыл бұрын

Nice video! Some kits come with a new diaphragm (cup) for the small valve on the end. It would have been good to show its disassembly & installation.

@JamiesGarage1 Жыл бұрын

I've never seen those. The diaphragm is sealed shut so unless its expected to be cut open and glue it shut again, I'm not sure how that would be serviceable. I'll look into it though, thanks

@johnautry6851 10 ай бұрын

Thanks for the great vid. Very easy to follow. I am surprised that the orangy gasket on the flapper frame is not mentioned. Mine is degrading; I'm sure others are, too. If you try to clean it, good chance it will come apart. My o-ring, flapper( prolly original), and crank thingie looked really good. Frame gasket not so. Any thoughts on that frame gasket material? Seem like air will leak, maybe not critical though?

@chrisbradley3224 Жыл бұрын

Great video. Do you have any thoughts on S55 in general or the crank hub bolt capture vs full fixes?

@bimmerdan1091 5 ай бұрын

Excellent video

@JamiesGarage1 5 ай бұрын

Thank you! 🙏

@Aleks_Mechanics Жыл бұрын

notification squad, Have a nice weekend!🔥🔥🔥

@JamiesGarage1 Жыл бұрын

💪

@ricardasr32 8 ай бұрын

Should the flap be installed in completely closed position? I attached it to this plasti rod and its slightly open

@the-real-rg 6 ай бұрын

does the disa valve on the n52 engine suffer the same fate? if so, is there a rebuild kit for that one? I have a 2010 528i xdrive with the n52 engine and 125k miles. is there a list of things I should do to my engine in order to make it more reliable, like you did to ChrisFix's engine?

@bgm1958 Жыл бұрын

Completely off topic but I have a 1989 635 CSi; can you recommend some kind of software that will read the OBD I codes?

@marioturkalj1239 Жыл бұрын

What is in that big square part of disa valve? Watching this video and can't figure is there some parts inside or just empty plastic cover?

@Yassin-dp4xt 3 ай бұрын

Hi love the quality of work your provide ! I checked the disa on my 330CI from 2001 and 240 000 km on it. No problems at all. In my opinion it’s impossible in case this pin get lose, that she can reach the motor. And that’s because this pin has no space to move as the plenum is just behind. Are you sure about it ? Thanks,

@mikemd2697 2 ай бұрын

The risk of that pin falling out and into the intake occurs during the removal of the disa valve. As you pull on the disa valve to remove it in its entirety, it creates space behind the disa valve... enough space that the pin can then fall out and drop into the intake. The key is to be very aware of the angle while you are removing the disa valve and don't tilt it so much that the pin can fall out.

@seanchu9139 6 ай бұрын

lack of low end or high end torque? because i am experiencing no power at high rpms, and poor fuel economy but the push at low speeds is still strong (it still kicks)

@j-z75 3 ай бұрын

Looking to order the kit, but how do I know which O Ring to choose for my 2004 Z4 2.5i ?

@TheNizz95 Жыл бұрын

Hey Jamie i have a bmw e39 with m54b25 engine and it starts pulling after 4000rpm so could it be the disa valve or/and vanos? 175tkm on the meter. The idele control valve gets stuck sometimes but not all the time. Thanks and keep on making good videos 👍

@JamiesGarage1 Жыл бұрын

It could be several different issues causing your concern. I'd recommend to remove the valve and inspect it like I show you in this video. You might find something.

@TheNizz95 Жыл бұрын

@@JamiesGarage1 thanks, going to check it at the same time i check the idle control valve.

@otto4399 11 ай бұрын

i have the symptoms.. but does it possibly make loud noice inside an exhaust?

@LEGENDoha9876 Жыл бұрын

I love watching your videos 😍 but as a German I can't help myself but giggle whenever you pronounce German words 🤣 It's Deesah Differenzierte Saugrohr Anlage 🤓

@maikelnait4495 3 ай бұрын

The function of this device is not affected by the mispronunciation.

@larryreno8293 4 ай бұрын

The rebuild does not address the bell crank shaft seal. That can be a vacuum leak source. I think this would be a strong argument fir entire valve replacement.

@superspeeder Жыл бұрын

What about the later N series engines? Are these valves still problematic? My wife’s 2011 2.5L E90 has a loss of midrange torque which wasn’t cured by replacing the VANOS solenoids. I’ve done lots of research and no concrete solution. I don’t want to continue throwing money at it without knowing the cause. Thanks!!!

@JamiesGarage1 Жыл бұрын

The N engines don't have a DISA so you're good there. You'll need to have it diagnosed to find the issue. Good luck 🤘

@meismyname Жыл бұрын

@@JamiesGarage1 Unfortunately that's incorrect. N52s (aside from the US 325i) have DISA valves, and the 3 state intake manifold found in the 330i and X3/X5 N52 models have two DISA valves, an inner and an outer. I had to replace both of mine. They're actuated with an electric motor and a worm gear, no vacuum pot. They can get worn out with time, but I don't believe they have the catastrophic issue like the M54s with the pin dropping out. The N52s will throw fault codes for DISA valve faults though.

@BLACKDAGGER794 Жыл бұрын

How much do you charge for an engine reinforcement like Chris fixs’ m54?

@leivabernie 7 ай бұрын

I’m gonna guess around 5-6k.

@traisharmon9765 Жыл бұрын

Do you know if this kit works for any other m5x disa valves In my case specifically a m52tu Or if the m54 disa would be compatible

@cheeseburgerbeefcake Жыл бұрын

I asked X8R if their DISA rebuild kit was suitable for the M52TUB25 engine in the early E46 323ci and they said their kits were not suitable. I have not contacted other vendors yet, I would also be interested in finding one!

@ivorvanwerven6210 Жыл бұрын

@@cheeseburgerbeefcake can also not find this info

@ivanmartinez9074 2 ай бұрын

Do they make these kits for the M52?

@TimeswitTray 7 ай бұрын

i repair the disa valve on my e39 528i 99 and now the car starts but wont run any sugguestions?

@turt1eforeva Жыл бұрын

I’m curious, do you know anybody with a 3d printer because they could’ve used polycarbonate and add a slide panel for the pivot screw for extra security and use the aluminum kit with the flap they sell on Amazon

@lauriewromar5478 7 ай бұрын

👏🏻👏🏻👍👍

@user-du2pw6sg1m 5 ай бұрын

Hello my friend, I have a problem with TRANS FAILSAFE PROG, and my transmission has become jerky and jerky. What is the solution?

@WildDigger Жыл бұрын

Can you rebuild the 2 Disas on the 3 stage intake manifold on the N52? The link only shows for the N54.

@dennisvandegrift9085 Жыл бұрын

You can install a 3 stage manifold on a N52 engine. They don’t come with it as a stock manifold and I would repair the used DISA valves while you’re doing it. I am in the planning stages of this upgrade currently for my 2008 Z4 3.0I with the N52 engine.

@WildDigger Жыл бұрын

@@dennisvandegrift9085 a 3.0 si z4 does come with a 3 stage manifold.

@royquesada5295 Жыл бұрын

Love 'pocket prybar😅😅😅

@gdubia 2 ай бұрын

The link to buy the M54 3.0 DISA rebuild kit doesn't seem to be working. Can you point me to where I can buy this kit?

@mikemd2697 2 ай бұрын

I literally just ordered a kit on Amazon but I have a 2.5 M54 so it's slightly different ( the main flap is a different length ) so be careful when ordering the right one for your 3.0 M54. I chose not to order the more expensive aluminum kit and opted for the $16.95 plastic rebuild kit, LOSTAR brand that had 100 ratings with a 4.3 star average review.

@waqarqadeer5217 Жыл бұрын

So is it like throttle body or it is different?

@JamiesGarage1 Жыл бұрын

Different. The engine has a throttle body, this is only used to direct the air through the intake manifold for more or less air volume depending on the engine's needs

@Revedance2002 Жыл бұрын

Is it the same for N52 engines?

@JamiesGarage1 Жыл бұрын

N52 doesn't use a DISA valve so you're all good.

@faridb40 Жыл бұрын

Has BMW fixed this valve on their newer models?

@barne3668 9 ай бұрын

fuk no

@LifeWideOpen780 Жыл бұрын

Can you do this with out removing the intake?

@ibrahimmoussa3711 Жыл бұрын

Sure you can

@ericgutierrez812 Жыл бұрын

Yes you can but removing the intake isn't difficult and I recommend doing so so that you can clean it as well as inspect your intake boot and throttle body

@JamiesGarage1 Жыл бұрын

Yep!

@Vyker Жыл бұрын

Where's the valve in a N55?

@ibrahimmoussa3711 Жыл бұрын

Comment first then watch 😂😅

@JamiesGarage1 Жыл бұрын

Always! 😅

@gregjohnson2073 Жыл бұрын

How much is a new valve?

@JamiesGarage1 Жыл бұрын

I supplied a link in the description, you could also find aftermarket valves for less but I only trust OEM for the DISA.

@demcomp Жыл бұрын

Pocket pry bar 🤣 aka a terminal driver

@justindaniels17 Жыл бұрын

Imma just delete the disa valve

@krismorey Ай бұрын

I laughed, yo what? Lol

@justindaniels17 Ай бұрын

@@krismorey I'm glad I got someone to laugh 😂😂

@JACKSON-rg5bx Жыл бұрын

I have an m54b25 want to build it for me 👍 ✨plz✨

@FBI_Master Жыл бұрын

just me or does this sound like an AI did the first 30 seconds

@robertadrianwayne Жыл бұрын

First 10 seconds are very odd.

@HarrryHarrry Жыл бұрын

Es ist unmöglich, daß der Pin im eingebauten Zustand aus der Disa heraus fällt!!! Is is impossible, that the axle fell out of the DISA, if the DISA is built-in tinto the intake manifold. Main part of the DISA which fails is the "motor" of it. The diaphragm breaks. So, do not waste money on a kit - buy directly a new original complete one.

@Kamal_AL-Hinai Жыл бұрын

of course its plastic

@1djbecker 5 ай бұрын

The plastic construction wasn't the source of the failures. It's the design and material selection. The original flap and linkage used a heavily glass-filled resin. Normally a high glass fill strengthens the plastic and extends the service life, at the expense of mold wear. In this case the glass fill acted as an abrasive. If the flap is able to move slightly, it flutters and the vibrating mating surfaces grind away at each other. When loose, the fluttering might loosen the upper metal and start wear there.

@milk-it Жыл бұрын

Why do I get the feeling BMW didn't make this part out of aluminium initially? This check probably isn't even part of their scheduled service policy. Probably designed to fail to get you to buy a new car. Engineered obsolesce.

@yycsky Жыл бұрын

First

@JamiesGarage1 Жыл бұрын

🏆

@ozstriker4075 26 күн бұрын

Waste of time, the majority of failures (all 3 of mine) are failure of the vacuum pot diaphragm which can't be serviced. You're better of just buying a a replacemt aftermarket DISA unit, they are good for 40k