In this video I show how I clean the chain using Muc-Off Chain Cleaner, lubricate it with WD-40 Chain Lube and finish off by adjusting the slack.
Пікірлер: 37
@MrDeepseadweller11 ай бұрын
Another often overlooked step is removing the front sprocket cover and cleaning away all the accumulated wax/lube and road debris. Only takes a few minutes and if you’ve never done it you will be surprised how much gunk is in there. Kerosene is all you need for cleaning the chain and sprocket area, then finish with a light coating of Maxima Chain Wax.
@Scoodee175 ай бұрын
Been using kerosene for years, cheap and works brilliant 👌
@justa_dude2 жыл бұрын
Thank you, your video helped me adjust my chain on my s1k
@SuperBloder Жыл бұрын
Thanks 4 the vid my friend
@rsaba2 жыл бұрын
Thank you, sir !
@drewtaylor98442 жыл бұрын
With the book just saying push up I feel like I haft to take that literally it’s really frustrating 🤣what’s your thoughts about this please
@bluebottle19882 жыл бұрын
Not sure about you use of cleaner and WD-40. Personally, I just use kerosene as recommended by the manufacturer and works really well to clean the chain and rims. I have seen people complain about the use of WD-40 but have seen others use it with no problem. It seems the take away was that you would need to do weekly maintenance when using WD-40. Personally, I use a teflon-based chain lubricant by dupont. Goes on wet and becomes like a wax and appears to have done the job well for the ten years I have been using it.
@Juanitoabusadorcachondo2 жыл бұрын
I use diesel for years no problem here
@KelsS1k2 жыл бұрын
Kerosene is good stuff thats what i use, Strips all the grime from the chain
@skippynj1979 Жыл бұрын
The wd40 he's using is the chain formula, it's not as penetrating as the other. I would not use plain wd40
@rollingstone16894 ай бұрын
Hi all. Watched a alot of videos on the bmw 1000 range bikes. I see on the rear sprockets that some have the flat side facing out and some have the liped side facing out. Is ther a right way or wrong way the have the rear sprocket facing,?
@markshomeengineering52434 ай бұрын
I don't know, mine is as it came from the factory. Cheers, Mark.
@rollingstone16894 ай бұрын
Following up what I posted I replaced my factory chains and sprocket. Igot a jt sprocket and a DID chain I removed the hub from the wheel and placed it on a flat surface and measured from the top of the sprocket to the desk. then I removed the sprocket placed the jt sprocket with the lip side facing out and got around a 3 mm difference then with the lip side facing the hub I got the same measured as the factory spec.
@phantombigballs81655 ай бұрын
Parafin, all you need for chain cleaning. Cheap and cuts grease and all the shite off...rinse, dry the chain and relube
@bernhtp2 жыл бұрын
Kerosene is cheap and amazing as a cleaner. Gear oil is cheap and amazing as a lubricant (far better than WD-40). I clean immediately before a wash, and lubricate at the end of the wash. This eliminates the need for a cardboard protector. I also do the cleaning/lubing in the ill-advised manner of running on my rear stand, which makes for the process being faster and more thorough. Regardless of what anyone says, this is the least dangerous thing I do on my RR.
@markshomeengineering52432 жыл бұрын
I can't condone your method of running on the rear stand, but you make a good point 🤣 I use paraffin (as we call it) on cleaning engine internals but never considered it for chains. I'll give it a go. Cheers
@bikemenace21452 жыл бұрын
How do you lube the inside plates of the chain when you have it running? I do all 4 sides of the chain to keep the rust from the plates, unless this isn't necessary.
@MSmifffy2 жыл бұрын
@@bikemenace2145 Hi, I don't bother, I rely on there being enough lube to work its way over the sides. It's not been a problem yet, 7.5k miles, mainly in the dry 😁
@bikemenace21452 жыл бұрын
@@MSmifffy I'll give that a try. I wonder if I'm actually overusing lube, though I do ride in the wet and damp too. Am I right in thinking you only spray the top and bottom of the chain then?
@bernhtp2 жыл бұрын
@@bikemenace2145 I apply the lube oil with one hand while holding the 3-sided brush against the moving chain with the other. The brush guarantees thorough spread and penetration.
@prabhat0982 жыл бұрын
I am using bmw M performance chain. Just need adjustments no need to lube or clean for a very very long time.
@balazsczedula9010 Жыл бұрын
chain sag needs to be measured with the bike on the sidestand
@TheArtsOfSense11 ай бұрын
that's not true, you can do it on the rear stand aswell, as the weight is still on the rear axis. You can't do it on a central stand though
@djfontable8 ай бұрын
@@TheArtsOfSenseit is true, as some of the weight is taken by the stand.
@ravenmoto310 Жыл бұрын
Axle nut torque spec is 92 ft lbs, 124 nm. Its in the manual! Page 195
@markshomeengineering5243 Жыл бұрын
I don't know what manual you are referring to, but the manual that came with the bike clearly states 100NM on page 208.
@ravenmoto5948 Жыл бұрын
In my 2021 S1000RR manual. What year is yours?
@markshomeengineering5243 Жыл бұрын
@@ravenmoto5948 2020
@ravenmoto5948 Жыл бұрын
@@markshomeengineering5243 Well, that is strange they increased it
@ryant9418 Жыл бұрын
@ravenmoto5948 my 2021 says 125nm on the plate the axle goes through
@hzjanjua432 жыл бұрын
I think your movement of chain was 40-70 mm not 45-50 mm