hyundai tucson rear brake pads and discs and shoes

Рет қаралды 6,906

9 ай бұрын

business and permissions inquires bodgitandleggit@gmail.com
If an Bodgit And Leggit Garage, Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE:
/ bodgitandleggitgarage
paypal.me/bodgitnleggit
ko-fi.com/bodgitandleggitgarage
/ bodgitandleggitgarage
bodgit and leggit garage
tips and tricks inside this video hopefully help you
don't forget get your hands dirty
www.bodgitandleggitgarage.com/
bodgitandleggitforum.editboard...
/ bodgitandleggitgarage
/ bodgitandleggitgarage
Disclaimer:
Due to factors beyond the control of Bodgit And Leggit Garage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Bodgit And Leggit Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Bodgit And Leggit Garage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Bodgit And Leggit Garage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained

Пікірлер: 40

@steveselvage40 9 ай бұрын

I learnt something today, im nearly 65 and have always been unsure of the amount of drag to leave on the shoes so often have to re adjust the brakes after a few weeks. Thank you 😊

@johnt7232 9 ай бұрын

Hi there I am only after coming across your channel for the first time today , I was searching for help on a Renault master van , the first one i found was the one about settling the hinge on the back door , thank you so much for the video , I HAD MINE FIXED IN FIVE MINUTES cheers

@bartoszk4812 9 ай бұрын

Done same design twice this year for my mates on a Kia Sportage and Chevrolet Captiva.. quite enjoy working on brakes 😊

@neill4133 9 ай бұрын

Is this the same setup for electric handbrake models or do they work on the calipers?

@andybramwell9179 9 ай бұрын

Literally just did this on my Captiva today. Deja bloody Vu. 😂😂

@michaeljohnson1006 9 ай бұрын

You can get a small led on the end of a flexible wire with watch batteries. They are small enough to poke though the hole and still see the adjuster I used one on my dad's Peugeot 406.

@eddieMurphy11111 9 ай бұрын

I bought a pair of those pliers quite a few years ago from Corfu but I lost them a couple of years later i think i left them in a car I put in part exchange I will have to invest again I am not sure i like those shoe and pad brakes but thanks for the video

@spawntohell 8 ай бұрын

interesting 14 on caliper and also 14 on carrier... most of time carrier will be at least 17 up to 21 -22 and tight as...

@michaeljohnson1006 9 ай бұрын

And the shoes are smaller on the cars with disks and shoes on the back so the hand brakes not as good as with just drums.

@bestbuildpc 9 ай бұрын

I guess u need to make a new video hahaha. Don't worry! Everything is fine. Thanks for sharing. Those brakes shoes are pain in the ass. Believe me! I've been there with Peugeot 406.

@GoWstingray 9 ай бұрын

How come the hand brake shoes required changing, they should last the life of the car and 2017, sounds unessersary, I know your doing the work for another garage by the way, genuinely interested?

@davyarthurs 9 ай бұрын

No locktite on the bolts so won’t be putting any on I hear you say - that’s of course if the person before you did it correctly 😝. Obv this is prob 1st time around for this car, so you’re safe.

@metalworker007 9 ай бұрын

My experience ..knocking off edge fine on pads but not shoes ...what happens when you do that is the powered brake dust gets under the shoes ..and you can actually hear it ...leave the edge alone and it acts as a wiper pushing the dust out of the way and water should it get soaked...and hopefully out of the drum if you haven't got a wear ridge...its ok to put a measly chamfer on it no more than 1/2 - 1mm....no more o help it for the frst few miles

@timahad5165 9 ай бұрын

Wrong, it's actually good practice to apply a taper on the leading edge of the brake shoe but leave the trailing edge alone as the leading edge will take most of the initial braking force.

@lesbaty8919 8 ай бұрын

Do these brake shoes do any actual braking or do they just hold the vehicle when stationary?

@SzwarcuKX5 9 ай бұрын

Hello Leon. Why shouldn't I use impact gun on lug nuts?

@howardbatty254 9 ай бұрын

Hi. He did say not to use the impact on the locking lug nut only. You don't want to be damaging that.

@SzwarcuKX5 9 ай бұрын

@@howardbatty254 How can you damage the nuts with the impact gun? Mine are in great shape. Don't use tone of torque and it will be fine.

@tomwalma4762 9 ай бұрын

those brake shoes look new;

@timothyosullivan2904 9 ай бұрын

I just watched your video replacing Hand brake shoes and brake pads , ? I'm surprised that you did not release the tension on the handbrake cables before installing the Shoes and have them adjusted properly afterwards to ensure that you had a proper and effective handbrake afterwards , I thought it a bit slack on your Professionalism , also you could have given the chambers where the brake pads slide a cleaning with a good wire brush just to be sure , after all Brakes are so Important , Thank you

@robtaylor4462 9 ай бұрын

Same as a Kia Sportage mk 3/4

@terryatkinson3182 9 ай бұрын

Kia ceed is the same except you have to remove the tie arm as the bolt can't be reached 😢 Handbrake adjustment inside the car is a pain in d hole 😭

@ambydaly5713 9 ай бұрын

The ford mondeo mk4 just uses pads . A much easier setup and the handbrake does work. It has to pass mot. Yes definitely better than the old Mk 4 zephyr which was useless. This setup makes me think they just want to make money and complicated to stop home diy.

@paulheath7140 9 ай бұрын

Dont use brake cleaner on coated brake discs

@terryatkinson3182 9 ай бұрын

He's going to love you 😊

@bodgitandleggitgarage 9 ай бұрын

@terryatkinson3182 No, no I am going to be nice. I am looking forward to see where this is going, this should be really good🤣🤣🤣🤣🤣

@timahad5165 9 ай бұрын

Memememe,😂

@mickymac6571 9 ай бұрын

You should always grease your pads and discs before fitting to make them last longer...

@scotspie501douglas7 9 ай бұрын

why dont you just get a impact gun and your using the hammer wrong who hits it side on

@priteshchampaneri5101 9 ай бұрын

I do!

@bodgitandleggitgarage 9 ай бұрын

@priteshchampaneri5101 I do too 😁

@priteshchampaneri5101 9 ай бұрын

@@bodgitandleggitgarage Makes it easier when you’re hitting a small surface area like that!

@bodgitandleggitgarage 9 ай бұрын

@@priteshchampaneri5101yep😁

@fanfeck2844 9 ай бұрын

He’s showing people how to do it who might not have expensive tools. I’ve been DIYing cars for over forty years, and have never needed a power tool

@DavidAlexander-gu6dh Ай бұрын

Couldn't finish watching the video.... blathering on about nothing

@bodgitandleggitgarage Ай бұрын

😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂 love you too

@Land2020-w6w 9 ай бұрын

Blowing out a brake shoes is NOT RECOMMENDED. Use brake cleaner to avoid dust from shoes and drum. P.S. Are you a qualified mechanic, just wondering.

@DavidAlexander-gu6dh Ай бұрын

WAY too much talking

@bodgitandleggitgarage Ай бұрын

Way too many comments